Using a Mini, with a maximum height object which was placed in the middle of the platform:
During end.gcode (after the object has just finished printing) it was possible to run into the part leaving an ugly melt mark.
M140 S0 ; heated bed heater off (if you have it)
M107 ; fans off
G92 E5 ; set extruder to 5mm for retract on print end
- G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
M190 R50 ; wait for bed to cool
- M104 S0 ;
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
M84 ; steppers off
G90 ; absolute positioning
;{profile_string}
M140 S0 ; heated bed heater off (if you have it)
M107 ; fans off
G92 E5 ; set extruder to 5mm for retract on print end
- G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
M190 R50 ; wait for bed to cool
- M104 S0 ;
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
M84 ; steppers off
G90 ; absolute positioning
;{profile_string}
M140 S0 ; heated bed heater off (if you have it)
M107 ; fans off
G92 E5 ; set extruder to 5mm for retract on print end
- G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
M190 R50 ; wait for bed to cool
- M104 S0 ;
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
M84 ; steppers off
G90 ; absolute positioning
;{profile_string}
M140 S0 ; heated bed heater off (if you have it)
M107 ; fans off
G92 E5 ; set extruder to 5mm for retract on print end
- G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
M190 R50 ; wait for bed to cool
- M104 S0 ;
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
M84 ; steppers off
G90 ; absolute positioning
;{profile_string}
M140 S0 ; heated bed heater off (if you have it)
M107 ; fans off
G92 E5 ; set extruder to 5mm for retract on print end
- G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
M190 R50 ; wait for bed to cool
- M104 S0 ;
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
M84 ; steppers off
G90 ; absolute positioning
;{profile_string}
M140 S0 ; heated bed heater off (if you have it)
M107 ; fans off
G92 E5 ; set extruder to 5mm for retract on print end
- G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
M190 R50 ; wait for bed to cool
- M104 S0 ;
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
M84 ; steppers off
G90 ; absolute positioning
;{profile_string}
G4 S15 ; wait for bed to temp up
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
-end.gcode = M400
- M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E5 ; set extruder to 5mm for retract on print end
- G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
- M190 R50 ; wait for bed to cool
- M104 S0 ;
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+end.gcode =
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G4 S25 ; wait for bed to temp up
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
-end.gcode = M400
- M104 S0 ; Hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E0 ; set extruder to 0
- G1 E-3 F300 ; retract a bit to relieve pressure
- G1 X5 Y5 Z156 F10000 ; move to cooling positioning
- M190 R60 ; wait for bed to cool
- M140 S0 ; turn off bed temp
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+end.gcode =
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R60 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G4 S25 ; wait for bed to temp up
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
-end.gcode = M400
- M104 S0 ; Hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E0 ; set extruder to 0
- G1 E-3 F300 ; retract a bit to relieve pressure
- G1 X5 Y5 Z156 F10000 ; move to cooling positioning
- M190 R60 ; wait for bed to cool
- M140 S0 ; turn off bed temp
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+end.gcode =
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R60 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G4 S25 ; wait for bed to temp up
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
-end.gcode = M400
- M104 S0 ; Hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E0 ; set extruder to 0
- G1 E-3 F300 ; retract a bit to relieve pressure
- G1 X5 Y5 Z156 F10000 ; move to cooling positioning
- M190 R60 ; wait for bed to cool
- M140 S0 ; turn off bed temp
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+end.gcode =
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R60 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
[profile]
-layer_height = 0.18
+layer_height = 0.15
wall_thickness = 1.0
retraction_enable = True
-solid_layer_thickness = 1.08
+solid_layer_thickness = 0.6
fill_density = 20
perimeter_before_infill = True
nozzle_size = 0.5
print_speed = 50
-print_temperature = 230
+print_temperature = 245
print_temperature2 = 0
print_temperature3 = 0
print_temperature4 = 0
print_temperature5 = 0
-print_bed_temperature = 60
+print_bed_temperature = 65
support = None
platform_adhesion = None
support_dual_extrusion = Both
filament_diameter4 = 0
filament_diameter5 = 0
filament_flow = 100.0
-retraction_speed = 10
-retraction_amount = 1
+retraction_speed = 25
+retraction_amount = 2.5
retraction_dual_amount = 16.5
-retraction_min_travel = 1.5
+retraction_min_travel = 1
retraction_combing = All
retraction_minimal_extrusion = 0.005
retraction_hop = 0.1
object_sink = 0.0
overlap_dual = 0.15
travel_speed = 175
-bottom_layer_speed = 8
-infill_speed = 30
+bottom_layer_speed = 20
+infill_speed = 20
solidarea_speed = 20
inset0_speed = 20
-insetx_speed = 25
-cool_min_layer_time = 15
+insetx_speed = 20
+cool_min_layer_time = 13
fan_enabled = True
skirt_line_count = 1
skirt_gap = 3.0
skirt_minimal_length = 250
fan_full_height = 0.5
-fan_speed = 75
+fan_speed = 100
fan_speed_max = 100
cool_min_feedrate = 10
cool_head_lift = False
fill_overlap = 15
support_type = Lines
support_angle = 45
-support_fill_rate = 30
+support_fill_rate = 20
support_xy_distance = 0.7
support_z_distance = 0.05
spiralize = False
.
object_center_x = -1
object_center_y = -1
+simplemodesettings =
+simplemodeprofile = Standard
+simplemodematerial = PLA
+simplemodematerialtype = Beginner
[alterations]
start.gcode = ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
G4 S25 ; wait for bed to temp up
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
-end.gcode = M400
- M104 S0 ; Hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E0 ; set extruder to 0
- G1 E-3 F300 ; retract a bit to relieve pressure
- G1 X5 Y5 Z156 F10000 ; move to cooling positioning
- M190 R60 ; wait for bed to cool
- M140 S0 ; turn off bed temp
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+end.gcode =
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R60 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
cool_start.gcode =
cool_end.gcode =
replace.csv =
-preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
- ;This code is added before the T(n)
+preswitchextruder.gcode = ;Switch between the current extruder and the next ex
postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
;This code is added after the T(n)
[profile]
-layer_height = 0.38
+layer_height = 0.4
wall_thickness = 1.0
retraction_enable = True
-solid_layer_thickness = 0.8
+solid_layer_thickness = 1.2
fill_density = 20
+perimeter_before_infill = True
nozzle_size = 0.5
print_speed = 50
-print_temperature = 240
+print_temperature = 245
print_temperature2 = 0
print_temperature3 = 0
print_temperature4 = 0
-print_bed_temperature = 60
+print_temperature5 = 0
+print_bed_temperature = 75
support = None
platform_adhesion = None
support_dual_extrusion = Both
filament_diameter2 = 0
filament_diameter3 = 0
filament_diameter4 = 0
+filament_diameter5 = 0
filament_flow = 100.0
-retraction_speed = 10
-retraction_amount = 1
+retraction_speed = 25
+retraction_amount = 4
retraction_dual_amount = 16.5
-retraction_min_travel = 1.5
+retraction_min_travel = 1
retraction_combing = All
retraction_minimal_extrusion = 0.005
retraction_hop = 0.1
object_sink = 0.0
overlap_dual = 0.15
travel_speed = 175
-bottom_layer_speed = 15
-infill_speed = 60
-solidarea_speed = 50
-inset0_speed = 50
-insetx_speed = 55
-cool_min_layer_time = 15
+bottom_layer_speed = 20
+infill_speed = 20
+solidarea_speed = 20
+inset0_speed = 20
+insetx_speed = 20
+cool_min_layer_time = 5
fan_enabled = True
skirt_line_count = 1
skirt_gap = 3.0
skirt_minimal_length = 250
fan_full_height = 0.5
-fan_speed = 40
-fan_speed_max = 60
+fan_speed = 100
+fan_speed_max = 100
cool_min_feedrate = 10
cool_head_lift = False
solid_top = True
fill_overlap = 15
support_type = Lines
support_angle = 45
-support_fill_rate = 30
+support_fill_rate = 20
support_xy_distance = 0.7
support_z_distance = 0.05
spiralize = False
raft_base_linewidth = 1.0
raft_interface_thickness = 0.27
raft_interface_linewidth = 0.4
+raft_airgap_all = 0.0
raft_airgap = 0.5
raft_surface_layers = 2
+raft_surface_thickness = 0.27
+raft_surface_linewidth = 0.4
fix_horrible_union_all_type_a = True
fix_horrible_union_all_type_b = False
fix_horrible_use_open_bits = False
.
object_center_x = -1
object_center_y = -1
+simplemodesettings =
+simplemodeprofile = Standard
+simplemodematerial = PLA
+simplemodematerialtype = Beginner
[alterations]
start.gcode = ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
G4 S25 ; wait for bed to temp up
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
-end.gcode = M400
- M104 S0 ; Hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E0 ; set extruder to 0
- G1 E-3 F300 ; retract a bit to relieve pressure
- G1 X5 Y5 Z156 F10000 ; move to cooling positioning
- M190 R60 ; wait for bed to cool
- M140 S0 ; turn off bed temp
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+end.gcode =
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R60 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
cool_start.gcode =
cool_end.gcode =
replace.csv =
-preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
- ;This code is added before the T(n)
+preswitchextruder.gcode = ;Switch between the current extruder and the next ex
postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
;This code is added after the T(n)
layer_height = 0.25
wall_thickness = 1.0
retraction_enable = True
-solid_layer_thickness = 0.8
+solid_layer_thickness = 1
fill_density = 20
+perimeter_before_infill = True
nozzle_size = 0.5
print_speed = 50
-print_temperature = 235
+print_temperature = 245
print_temperature2 = 0
print_temperature3 = 0
print_temperature4 = 0
-print_bed_temperature = 60
+print_temperature5 = 0
+print_bed_temperature = 75
support = None
platform_adhesion = None
support_dual_extrusion = Both
filament_diameter2 = 0
filament_diameter3 = 0
filament_diameter4 = 0
+filament_diameter5 = 0
filament_flow = 100.0
-retraction_speed = 10
-retraction_amount = 1
+retraction_speed = 25
+retraction_amount = 4
retraction_dual_amount = 16.5
-retraction_min_travel = 1.5
+retraction_min_travel = 1
retraction_combing = All
retraction_minimal_extrusion = 0.005
retraction_hop = 0.1
object_sink = 0.0
overlap_dual = 0.15
travel_speed = 175
-bottom_layer_speed = 10
-infill_speed = 40
-solidarea_speed = 35
-inset0_speed = 35
-insetx_speed = 37
-cool_min_layer_time = 15
+bottom_layer_speed = 20
+infill_speed = 20
+solidarea_speed = 20
+inset0_speed = 20
+insetx_speed = 20
+cool_min_layer_time = 5
fan_enabled = True
skirt_line_count = 1
skirt_gap = 3.0
skirt_minimal_length = 250
fan_full_height = 0.5
-fan_speed = 40
-fan_speed_max = 60
+fan_speed = 100
+fan_speed_max = 100
cool_min_feedrate = 10
cool_head_lift = False
solid_top = True
fill_overlap = 15
support_type = Lines
support_angle = 45
-support_fill_rate = 30
+support_fill_rate = 20
support_xy_distance = 0.7
support_z_distance = 0.05
spiralize = False
raft_base_linewidth = 1.0
raft_interface_thickness = 0.27
raft_interface_linewidth = 0.4
+raft_airgap_all = 0.0
raft_airgap = 0.5
raft_surface_layers = 2
+raft_surface_thickness = 0.27
+raft_surface_linewidth = 0.4
fix_horrible_union_all_type_a = True
fix_horrible_union_all_type_b = False
fix_horrible_use_open_bits = False
.
object_center_x = -1
object_center_y = -1
+simplemodesettings =
+simplemodeprofile = Standard
+simplemodematerial = PLA
+simplemodematerialtype = Beginner
[alterations]
start.gcode = ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
G4 S25 ; wait for bed to temp up
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
-end.gcode = M400
- M104 S0 ; Hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E0 ; set extruder to 0
- G1 E-3 F300 ; retract a bit to relieve pressure
- G1 X5 Y5 Z156 F10000 ; move to cooling positioning
- M190 R60 ; wait for bed to cool
- M140 S0 ; turn off bed temp
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+end.gcode =
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R60 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
cool_start.gcode =
cool_end.gcode =
replace.csv =
-preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
- ;This code is added before the T(n)
+preswitchextruder.gcode = ;Switch between the current extruder and the next ex
postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
;This code is added after the T(n)
G4 S25 ; wait for bed to temp up
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
-end.gcode = M400
- M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E0 ; set extruder to 0
- G1 E-3 F300 ; retract a bit to relieve pressure
- G1 X5 Y5 Z156 F10000 ; move to cooling positioning
- M190 R60 ; wait for bed to cool
- M140 S0 ; turn off bed
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+end.gcode =
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R60 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G4 S25 ; wait for bed to temp up
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
-end.gcode = M400
- M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E0 ; set extruder to 0
- G1 E-3 F300 ; retract a bit to relieve pressure
- G1 X5 Y5 Z156 F10000 ; move to cooling positioning
- M190 R60 ; wait for bed to cool
- M140 S0 ; turn off bed
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+end.gcode =
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R60 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G4 S25 ; wait for bed to temp up
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
-end.gcode = M400
- M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E0 ; set extruder to 0
- G1 E-3 F300 ; retract a bit to relieve pressure
- G1 X5 Y5 Z156 F10000 ; move to cooling positioning
- M190 R60 ; wait for bed to cool
- M140 S0 ; turn off bed
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+end.gcode =
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R60 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G4 S25 ; wait for bed to temp up
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
-end.gcode = M400
- M104 S0 ; Hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E0 ; set extruder to 0
- G1 E-3 F300 ; retract a bit to relieve pressure
- G1 X5 Y5 Z156 F10000 ; move to cooling positioning
- M190 R60 ; wait for bed to cool
- M140 S0 ; turn off bed temp
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+end.gcode =
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R60 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G4 S25 ; wait for bed to temp up
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
-end.gcode = M400
- M104 S0 ; Hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E0 ; set extruder to 0
- G1 E-3 F300 ; retract a bit to relieve pressure
- G1 X5 Y5 Z156 F10000 ; move to cooling positioning
- M190 R60 ; wait for bed to cool
- M140 S0 ; turn off bed temp
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+end.gcode =
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R60 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
end.gcode =
- M400
- M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E5 ; set extruder to 5mm for retract on print end
- G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
- M190 R50 ; wait for bed to cool
- M140 S0 ; bed off
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
end.gcode =
- M400
- M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E5 ; set extruder to 5mm for retract on print end
- G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
- M190 R50 ; wait for bed to cool
- M140 S0 ; shut off bed
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
end.gcode =
- M400
- M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E5 ; set extruder to 5mm for retract on print end
- G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
- M190 R50 ; wait for bed to cool
- M140 S0 ;
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
end.gcode =
- M400
- M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E5 ; set extruder to 5mm for retract on print end
- G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
- M190 R50 ; wait for bed to cool
- M140 S0 ; bed off
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G4 S25 ; wait for bed to temp up
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
-end.gcode = M400
- M104 S0 ; Hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E0 ; set extruder to 0
- G1 E-3 F300 ; retract a bit to relieve pressure
- G1 X5 Y5 Z156 F10000 ; move to cooling positioning
- M190 R60 ; wait for bed to cool
- M140 S0 ; turn off bed temp
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+end.gcode =
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R60 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G4 S25 ; wait for bed to temp up
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
-end.gcode = M400
- M104 S0 ; Hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E0 ; set extruder to 0
- G1 E-3 F300 ; retract a bit to relieve pressure
- G1 X5 Y5 Z156 F10000 ; move to cooling positioning
- M190 R60 ; wait for bed to cool
- M140 S0 ; turn off bed temp
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+end.gcode =
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R60 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G4 S25 ; wait for bed to temp up
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
-end.gcode = M400
- M104 S0 ; Hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E0 ; set extruder to 0
- G1 E-3 F300 ; retract a bit to relieve pressure
- G1 X5 Y5 Z156 F10000 ; move to cooling positioning
- M190 R60 ; wait for bed to cool
- M140 S0 ; turn off bed temp
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+end.gcode =
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R60 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
end.gcode =
- M400
- M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E5 ; set extruder to 5mm for retract on print end
- G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
- M190 R50 ; wait for bed to cool
- M140 S0 ; bed off
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G4 S15 ; wait for bed to temp up
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
-end.gcode = M400
- M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E5 ; set extruder to 5mm for retract on print end
- G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
- M190 R50 ; wait for bed to cool
- M140 S0 ; bed off
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+end.gcode =
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
end.gcode =
- M400
- M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E5 ; set extruder to 5mm for retract on print end
- G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
- M190 R50 ; wait for bed to cool
- M140 S0 ; bed off
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
end.gcode =
- M400
- M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E5 ; set extruder to 5mm for retract on print end
- G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
- M190 R50 ; wait for bed to cool
- M140 S0 ; bed off
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
end.gcode =
- M400
- M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E5 ; set extruder to 5mm for retract on print end
- G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
- M190 R50 ; wait for bed to cool
- M140 S0 ; bed off
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
end.gcode =
- M400
- M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E5 ; set extruder to 5mm for retract on print end
- G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
- M190 R50 ; wait for bed to cool
- M140 S0 ; bed off
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
end.gcode =
- M400
- M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E5 ; set extruder to 5mm for retract on print end
- G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
- M190 R50 ; wait for bed to cool
- M140 S0 ; bed off
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
end.gcode =
- M400
- M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E5 ; set extruder to 5mm for retract on print end
- G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
- M190 R50 ; wait for bed to cool
- M140 S0 ; bed off
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
end.gcode =
- M400
- M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E5 ; set extruder to 5mm for retract on print end
- G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
- M190 R50 ; wait for bed to cool
- M140 S0 ; bed off
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G4 S25 ; wait for bed to temp up
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
-end.gcode = M400
- M104 S0 ; Hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E0 ; set extruder to 0
- G1 E-3 F300 ; retract a bit to relieve pressure
- G1 X5 Y5 Z156 F10000 ; move to cooling positioning
- M190 R60 ; wait for bed to cool
- M140 S0 ; turn off bed temp
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+end.gcode =
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R60 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G4 S25 ; wait for bed to temp up
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
-end.gcode = M400
- M104 S0 ; Hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E0 ; set extruder to 0
- G1 E-3 F300 ; retract a bit to relieve pressure
- G1 X5 Y5 Z156 F10000 ; move to cooling positioning
- M190 R60 ; wait for bed to cool
- M140 S0 ; turn off bed temp
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+end.gcode =
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R60 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G4 S25 ; wait for bed to temp up
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
-end.gcode = M400
- M104 S0 ; Hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E0 ; set extruder to 0
- G1 E-3 F300 ; retract a bit to relieve pressure
- G1 X5 Y5 Z156 F10000 ; move to cooling positioning
- M190 R60 ; wait for bed to cool
- M140 S0 ; turn off bed temp
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+end.gcode =
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R60 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
end.gcode =
- M400
- M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E5 ; set extruder to 5mm for retract on print end
- G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
- M190 R50 ; wait for bed to cool
- M140 S0 ; bed off
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
end.gcode =
- M400
- M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E5 ; set extruder to 5mm for retract on print end
- G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
- M190 R50 ; wait for bed to cool
- M140 S0 ; bed off
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
end.gcode =
- M400
- M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E5 ; set extruder to 5mm for retract on print end
- G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
- M190 R50 ; wait for bed to cool
- M140 S0 ; bed off
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
end.gcode =
- M400
- M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E5 ; set extruder to 5mm for retract on print end
- G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
- M190 R50 ; wait for bed to cool
- M140 S0 ; bed off
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
end.gcode =
- M400
- M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E5 ; set extruder to 5mm for retract on print end
- G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
- M190 R50 ; wait for bed to cool
- M140 S0 ; bed off
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
end.gcode =
- M400
- M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E5 ; set extruder to 5mm for retract on print end
- G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
- M190 R50 ; wait for bed to cool
- M140 S0 ; bed off
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
travel_speed = 160
bottom_layer_speed = 10
infill_speed = 22
-solidarea_speed = 0.0
+solidarea_speed = 18
inset0_speed = 15
insetx_speed = 18
cool_min_layer_time = 45
simplemodesettings =
simplemodeprofile = 2_normal
simplemodematerial = 1_pla
+simplemodematerialtype = Beginner
[alterations]
start.gcode = ;This Gcode has been generated specifically for the LulzBot Mini
G4 S15 ; wait for bed to temp up
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
-end.gcode = M400
- M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E5 ; set extruder to 5mm for retract on print end
- G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
- M190 R50 ; wait for bed to cool
- M140 S0 ; bed off
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+end.gcode =
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
travel_speed = 160
bottom_layer_speed = 10
infill_speed = 18
-solidarea_speed = 0.0
+solidarea_speed = 14
inset0_speed = 10
insetx_speed = 14
cool_min_layer_time = 45
simplemodesettings =
simplemodeprofile = 2_normal
simplemodematerial = 1_pla
+simplemodematerialtype = Beginner
[alterations]
start.gcode = ;This Gcode has been generated specifically for the LulzBot Mini
G4 S15 ; wait for bed to temp up
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
-end.gcode = M400
- M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E5 ; set extruder to 5mm for retract on print end
- G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
- M190 R50 ; wait for bed to cool
- M140 S0 ; bed off
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+end.gcode =
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G4 S15 ; wait for bed to temp up
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
-end.gcode = M400
- M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E5 ; set extruder to 5mm for retract on print end
- G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
- M190 R50 ; wait for bed to cool
- M140 S0 ; bed off
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+end.gcode =
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
G1 Z2 E0 F75 ; extrude filament back into nozzle
M140 S{print_bed_temperature}; get bed temping up during first layer
end.gcode =
- M400
- M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E5 ; set extruder to 5mm for retract on print end
- G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
- M190 R50 ; wait for bed to cool
- M140 S0 ; bed off
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M140 S0 ;
+ G1 X145 F1000 ; move to cooling positioning
+ G1 Y175 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}