4 retraction_enable = True
5 solid_layer_thickness = 1.2
7 perimeter_before_infill = True
10 print_temperature = 245
11 print_temperature2 = 0
12 print_temperature3 = 0
13 print_temperature4 = 0
14 print_temperature5 = 0
15 print_bed_temperature = 75
17 platform_adhesion = None
18 support_dual_extrusion = Both
20 wipe_tower_volume = 15
22 filament_diameter = 2.85
23 filament_diameter2 = 0
24 filament_diameter3 = 0
25 filament_diameter4 = 0
26 filament_diameter5 = 0
30 retraction_dual_amount = 16.5
31 retraction_min_travel = 1
32 retraction_combing = All
33 retraction_minimal_extrusion = 0.005
35 bottom_thickness = 0.425
36 layer0_width_factor = 125
40 bottom_layer_speed = 20
45 cool_min_layer_time = 5
49 skirt_minimal_length = 250
53 cool_min_feedrate = 10
54 cool_head_lift = False
60 support_fill_rate = 20
61 support_xy_distance = 0.7
62 support_z_distance = 0.05
67 raft_line_spacing = 3.0
68 raft_base_thickness = 0.3
69 raft_base_linewidth = 1.0
70 raft_interface_thickness = 0.27
71 raft_interface_linewidth = 0.4
74 raft_surface_layers = 2
75 raft_surface_thickness = 0.27
76 raft_surface_linewidth = 0.4
77 fix_horrible_union_all_type_a = True
78 fix_horrible_union_all_type_b = False
79 fix_horrible_use_open_bits = False
80 fix_horrible_extensive_stitching = False
86 simplemodeprofile = Standard
87 simplemodematerial = PLA
88 simplemodematerialtype = Beginner
91 start.gcode = ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
92 ;Print time: {print_time}
93 ;Filament used: {filament_amount}m {filament_weight}g
94 ;Filament cost: {filament_cost}
95 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
96 ;M109 S{print_temperature} ;Uncomment to add your own temperature line
98 G90 ; absolute positioning
99 M82 ; set extruder to absolute mode
100 M107 ; start with the fan off
101 G92 E0 ; set extruder position to 0
102 M140 S{print_bed_temperature}; get bed heating up
104 M109 S150 ; set to cleaning temp and wait
105 G1 Z150 E-30 F75 ; suck up XXmm of filament
106 M109 S170 ; heat up rest of way
107 G1 X45 Y174 F11520 ; move behind scraper
108 G1 Z0 F1200 ; CRITICAL: set Z to height of top of scraper
109 G1 X45 Y174 Z-.5 F4000 ; wiping ; plunge into wipe pad
110 G1 X55 Y172 Z-.5 F4000 ; wiping
111 G1 X45 Y174 Z0 F4000 ; wiping
112 G1 X55 Y172 F4000 ; wiping
113 G1 X45 Y174 F4000 ; wiping
114 G1 X55 Y172 F4000 ; wiping
115 G1 X45 Y174 F4000 ; wiping
116 G1 X55 Y172 F4000 ; wiping
117 G1 X60 Y174 F4000 ; wiping
118 G1 X80 Y172 F4000 ; wiping
119 G1 X60 Y174 F4000 ; wiping
120 G1 X80 Y172 F4000 ; wiping
121 G1 X60 Y174 F4000 ; wiping
122 G1 X90 Y172 F4000 ; wiping
123 G1 X80 Y174 F4000 ; wiping
124 G1 X100 Y172 F4000 ; wiping
125 G1 X80 Y174 F4000 ; wiping
126 G1 X100 Y172 F4000 ; wiping
127 G1 X80 Y174 F4000 ; wiping
128 G1 X100 Y172 F4000 ; wiping
129 G1 X110 Y174 F4000 ; wiping
130 G1 X100 Y172 F4000 ; wiping
131 G1 X110 Y174 F4000 ; wiping
132 G1 X100 Y172 F4000 ; wiping
133 G1 X110 Y174 F4000 ; wiping
134 G1 X115 Y172 Z-0.5 F1000 ; wipe slower and bury noz in cleanish area
136 G28 X0 Y0 ; home x and y
137 M109 S170 ; set to probing temp
138 M204 S300 ; set accel for probing
140 M204 S2000 ; set accel back to normal
141 G1 X5 Y15 Z10 F5000 ; get out the way
144 M109 S{print_temperature} ; set extruder temp and wait
145 G4 S25 ; wait for bed to temp up
146 G1 Z2 E0 F75 ; extrude filament back into nozzle
147 M140 S{print_bed_temperature}; get bed temping up during first layer
151 M140 S0 ; heated bed heater off (if you have it)
153 G92 E5 ; set extruder to 5mm for retract on print end
154 G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
155 M190 R60 ; wait for bed to cool
157 G1 X145 F1000 ; move to cooling positioning
158 G1 Y175 F1000 ; move to cooling positioning
160 G90 ; absolute positioning
162 start2.gcode = ;Sliced at: {day} {date} {time}
163 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
164 ;Print time: {print_time}
165 ;Filament used: {filament_amount}m {filament_weight}g
166 ;Filament cost: {filament_cost}
167 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
168 ;M104 S{print_temperature} ;Uncomment to add your own temperature line
169 ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
170 ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
172 G90 ;absolute positioning
173 M107 ;start with the fan off
174 G28 X0 Y0 ;move X/Y to min endstops
175 G28 Z0 ;move Z to min endstops
176 G1 Z15.0 F{travel_speed} ;move the platform down 15mm
177 T1 ;Switch to the 2nd extruder
178 G92 E0 ;zero the extruded length
179 G1 F200 E10 ;extrude 10mm of feed stock
180 G92 E0 ;zero the extruded length again
181 G1 F200 E-{retraction_dual_amount}
182 T0 ;Switch to the first extruder
183 G92 E0 ;zero the extruded length
184 G1 F200 E10 ;extrude 10mm of feed stock
185 G92 E0 ;zero the extruded length again
187 ;Put printing message on LCD screen
189 end2.gcode = ;End GCode
190 M104 T0 S0 ;extruder heater off
191 M104 T1 S0 ;extruder heater off
192 M140 S0 ;heated bed heater off (if you have it)
193 G91 ;relative positioning
194 G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
195 G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
196 G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
198 G90 ;absolute positioning
200 start3.gcode = ;Sliced at: {day} {date} {time}
201 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
202 ;Print time: {print_time}
203 ;Filament used: {filament_amount}m {filament_weight}g
204 ;Filament cost: {filament_cost}
205 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
206 ;M104 S{print_temperature} ;Uncomment to add your own temperature line
207 ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
208 ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
210 G90 ;absolute positioning
211 M107 ;start with the fan off
212 G28 X0 Y0 ;move X/Y to min endstops
213 G28 Z0 ;move Z to min endstops
214 G1 Z15.0 F{travel_speed} ;move the platform down 15mm
215 T2 ;Switch to the 2nd extruder
216 G92 E0 ;zero the extruded length
217 G1 F200 E10 ;extrude 10mm of feed stock
218 G92 E0 ;zero the extruded length again
219 G1 F200 E-{retraction_dual_amount}
220 T1 ;Switch to the 2nd extruder
221 G92 E0 ;zero the extruded length
222 G1 F200 E10 ;extrude 10mm of feed stock
223 G92 E0 ;zero the extruded length again
224 G1 F200 E-{retraction_dual_amount}
225 T0 ;Switch to the first extruder
226 G92 E0 ;zero the extruded length
227 G1 F200 E10 ;extrude 10mm of feed stock
228 G92 E0 ;zero the extruded length again
230 ;Put printing message on LCD screen
232 end3.gcode = ;End GCode
233 M104 T0 S0 ;extruder heater off
234 M104 T1 S0 ;extruder heater off
235 M104 T2 S0 ;extruder heater off
236 M140 S0 ;heated bed heater off (if you have it)
237 G91 ;relative positioning
238 G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
239 G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
240 G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
242 G90 ;absolute positioning
244 start4.gcode = ;Sliced at: {day} {date} {time}
245 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
246 ;Print time: {print_time}
247 ;Filament used: {filament_amount}m {filament_weight}g
248 ;Filament cost: {filament_cost}
249 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
250 ;M104 S{print_temperature} ;Uncomment to add your own temperature line
251 ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
252 ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
253 ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
255 G90 ;absolute positioning
256 M107 ;start with the fan off
257 G28 X0 Y0 ;move X/Y to min endstops
258 G28 Z0 ;move Z to min endstops
259 G1 Z15.0 F{travel_speed} ;move the platform down 15mm
260 T3 ;Switch to the 4th extruder
261 G92 E0 ;zero the extruded length
262 G1 F200 E10 ;extrude 10mm of feed stock
263 G92 E0 ;zero the extruded length again
264 G1 F200 E-{retraction_dual_amount}
265 T2 ;Switch to the 3th extruder
266 G92 E0 ;zero the extruded length
267 G1 F200 E10 ;extrude 10mm of feed stock
268 G92 E0 ;zero the extruded length again
269 G1 F200 E-{retraction_dual_amount}
270 T1 ;Switch to the 2nd extruder
271 G92 E0 ;zero the extruded length
272 G1 F200 E10 ;extrude 10mm of feed stock
273 G92 E0 ;zero the extruded length again
274 G1 F200 E-{retraction_dual_amount}
275 T0 ;Switch to the first extruder
276 G92 E0 ;zero the extruded length
277 G1 F200 E10 ;extrude 10mm of feed stock
278 G92 E0 ;zero the extruded length again
280 ;Put printing message on LCD screen
282 end4.gcode = ;End GCode
283 M104 T0 S0 ;extruder heater off
284 M104 T1 S0 ;extruder heater off
285 M104 T2 S0 ;extruder heater off
286 M104 T3 S0 ;extruder heater off
287 M140 S0 ;heated bed heater off (if you have it)
288 G91 ;relative positioning
289 G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
290 G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
291 G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
293 G90 ;absolute positioning
295 support_start.gcode =
300 preswitchextruder.gcode = ;Switch between the current extruder and the next ex
301 postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
302 ;This code is added after the T(n)