4 retraction_enable = True
5 solid_layer_thickness = 1
7 perimeter_before_infill = True
10 print_temperature = 190
11 print_temperature2 = 0
12 print_temperature3 = 0
13 print_temperature4 = 0
14 print_temperature5 = 0
15 print_bed_temperature = 60
17 platform_adhesion = None
18 support_dual_extrusion = Both
20 wipe_tower_volume = 15
22 filament_diameter = 2.85
23 filament_diameter2 = 0
24 filament_diameter3 = 0
25 filament_diameter4 = 0
26 filament_diameter5 = 0
29 retraction_amount = 1.5
30 retraction_dual_amount = 16.5
31 retraction_min_travel = 1.5
32 retraction_combing = All
33 retraction_minimal_extrusion = 0.005
35 bottom_thickness = 0.425
36 layer0_width_factor = 125
40 bottom_layer_speed = 15
45 cool_min_layer_time = 5
49 skirt_minimal_length = 250
53 cool_min_feedrate = 10
54 cool_head_lift = False
60 support_fill_rate = 30
61 support_xy_distance = 0.7
62 support_z_distance = 0.05
67 raft_line_spacing = 3.0
68 raft_base_thickness = 0.3
69 raft_base_linewidth = 1.0
70 raft_interface_thickness = 0.27
71 raft_interface_linewidth = 0.4
74 raft_surface_layers = 2
75 raft_surface_thickness = 0.27
76 raft_surface_linewidth = 0.4
77 fix_horrible_union_all_type_a = True
78 fix_horrible_union_all_type_b = False
79 fix_horrible_use_open_bits = False
80 fix_horrible_extensive_stitching = False
85 simplemodeprofile = 2_normal
86 simplemodematerial = 1_pla
87 simplemodematerialtype = Beginner
90 start.gcode = ;This Gcode has been generated specifically for the LulzBot Mini
91 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
92 ;Filament Diameter: {filament_diameter}
93 ;Nozzle Size: {nozzle_size}
95 G90 ; absolute positioning
96 M82 ; set extruder to absolute mode
97 M107 ; start with the fan off
98 G92 E0 ; set extruder position to 0
99 M140 S{print_bed_temperature}; get bed heating up
101 M109 S130 ; set to cleaning temp and wait
102 G1 Z150 E-30 F75 ; suck up XXmm of filament
103 M109 S130 ; heat up rest of way
104 G1 X45 Y174 F11520 ; move behind scraper
105 G1 Z0 F1200 ; CRITICAL: set Z to height of top of scraper
106 G1 X45 Y174 Z-.5 F4000 ; wiping ; plunge into wipe pad
107 G1 X55 Y172 Z-.5 F4000 ; wiping
108 G1 X45 Y174 Z0 F4000 ; wiping
109 G1 X55 Y172 F4000 ; wiping
110 G1 X45 Y174 F4000 ; wiping
111 G1 X55 Y172 F4000 ; wiping
112 G1 X45 Y174 F4000 ; wiping
113 G1 X55 Y172 F4000 ; wiping
114 G1 X60 Y174 F4000 ; wiping
115 G1 X80 Y172 F4000 ; wiping
116 G1 X60 Y174 F4000 ; wiping
117 G1 X80 Y172 F4000 ; wiping
118 G1 X60 Y174 F4000 ; wiping
119 G1 X90 Y172 F4000 ; wiping
120 G1 X80 Y174 F4000 ; wiping
121 G1 X100 Y172 F4000 ; wiping
122 G1 X80 Y174 F4000 ; wiping
123 G1 X100 Y172 F4000 ; wiping
124 G1 X80 Y174 F4000 ; wiping
125 G1 X100 Y172 F4000 ; wiping
126 G1 X110 Y174 F4000 ; wiping
127 G1 X100 Y172 F4000 ; wiping
128 G1 X110 Y174 F4000 ; wiping
129 G1 X100 Y172 F4000 ; wiping
130 G1 X110 Y174 F4000 ; wiping
131 G1 X115 Y172 Z-0.5 F1000 ; wipe slower and bury noz in cleanish area
133 G28 X0 Y0 ; home x and y
134 M109 S130 ; set to probing temp
135 M204 S300 ; Set probing acceleration
137 M204 S2000 ; Restore standard acceleration
138 G1 X5 Y15 Z10 F5000 ; get out the way
141 M109 S{print_temperature} ; set extruder temp and wait
142 G4 S15 ; wait for bed to temp up
143 G1 Z2 E0 F75 ; extrude filament back into nozzle
144 M140 S{print_bed_temperature}; get bed temping up during first layer
148 M140 S0 ; heated bed heater off (if you have it)
150 G92 E5 ; set extruder to 5mm for retract on print end
151 G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
152 M190 R50 ; wait for bed to cool
154 G1 X145 F1000 ; move to cooling positioning
155 G1 Y175 F1000 ; move to cooling positioning
157 G90 ; absolute positioning
159 start2.gcode = ;Sliced at: {day} {date} {time}
160 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
161 ;Print time: {print_time}
162 ;Filament used: {filament_amount}m {filament_weight}g
163 ;Filament cost: {filament_cost}
164 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
165 ;M104 S{print_temperature} ;Uncomment to add your own temperature line
166 ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
167 ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
169 G90 ;absolute positioning
170 M107 ;start with the fan off
171 G28 X0 Y0 ;move X/Y to min endstops
172 G28 Z0 ;move Z to min endstops
173 G1 Z15.0 F{travel_speed} ;move the platform down 15mm
174 T1 ;Switch to the 2nd extruder
175 G92 E0 ;zero the extruded length
176 G1 F200 E10 ;extrude 10mm of feed stock
177 G92 E0 ;zero the extruded length again
178 G1 F200 E-{retraction_dual_amount}
179 T0 ;Switch to the first extruder
180 G92 E0 ;zero the extruded length
181 G1 F200 E10 ;extrude 10mm of feed stock
182 G92 E0 ;zero the extruded length again
184 ;Put printing message on LCD screen
186 end2.gcode = ;End GCode
187 M104 T0 S0 ;extruder heater off
188 M104 T1 S0 ;extruder heater off
189 M140 S0 ;heated bed heater off (if you have it)
190 G91 ;relative positioning
191 G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
192 G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
193 G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
195 G90 ;absolute positioning
197 start3.gcode = ;Sliced at: {day} {date} {time}
198 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
199 ;Print time: {print_time}
200 ;Filament used: {filament_amount}m {filament_weight}g
201 ;Filament cost: {filament_cost}
202 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
203 ;M104 S{print_temperature} ;Uncomment to add your own temperature line
204 ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
205 ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
207 G90 ;absolute positioning
208 M107 ;start with the fan off
209 G28 X0 Y0 ;move X/Y to min endstops
210 G28 Z0 ;move Z to min endstops
211 G1 Z15.0 F{travel_speed} ;move the platform down 15mm
212 T2 ;Switch to the 2nd extruder
213 G92 E0 ;zero the extruded length
214 G1 F200 E10 ;extrude 10mm of feed stock
215 G92 E0 ;zero the extruded length again
216 G1 F200 E-{retraction_dual_amount}
217 T1 ;Switch to the 2nd extruder
218 G92 E0 ;zero the extruded length
219 G1 F200 E10 ;extrude 10mm of feed stock
220 G92 E0 ;zero the extruded length again
221 G1 F200 E-{retraction_dual_amount}
222 T0 ;Switch to the first extruder
223 G92 E0 ;zero the extruded length
224 G1 F200 E10 ;extrude 10mm of feed stock
225 G92 E0 ;zero the extruded length again
227 ;Put printing message on LCD screen
229 end3.gcode = ;End GCode
230 M104 T0 S0 ;extruder heater off
231 M104 T1 S0 ;extruder heater off
232 M104 T2 S0 ;extruder heater off
233 M140 S0 ;heated bed heater off (if you have it)
234 G91 ;relative positioning
235 G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
236 G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
237 G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
239 G90 ;absolute positioning
241 start4.gcode = ;Sliced at: {day} {date} {time}
242 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
243 ;Print time: {print_time}
244 ;Filament used: {filament_amount}m {filament_weight}g
245 ;Filament cost: {filament_cost}
246 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
247 ;M104 S{print_temperature} ;Uncomment to add your own temperature line
248 ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
249 ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
250 ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
252 G90 ;absolute positioning
253 M107 ;start with the fan off
254 G28 X0 Y0 ;move X/Y to min endstops
255 G28 Z0 ;move Z to min endstops
256 G1 Z15.0 F{travel_speed} ;move the platform down 15mm
257 T3 ;Switch to the 4th extruder
258 G92 E0 ;zero the extruded length
259 G1 F200 E10 ;extrude 10mm of feed stock
260 G92 E0 ;zero the extruded length again
261 G1 F200 E-{retraction_dual_amount}
262 T2 ;Switch to the 3th extruder
263 G92 E0 ;zero the extruded length
264 G1 F200 E10 ;extrude 10mm of feed stock
265 G92 E0 ;zero the extruded length again
266 G1 F200 E-{retraction_dual_amount}
267 T1 ;Switch to the 2nd extruder
268 G92 E0 ;zero the extruded length
269 G1 F200 E10 ;extrude 10mm of feed stock
270 G92 E0 ;zero the extruded length again
271 G1 F200 E-{retraction_dual_amount}
272 T0 ;Switch to the first extruder
273 G92 E0 ;zero the extruded length
274 G1 F200 E10 ;extrude 10mm of feed stock
275 G92 E0 ;zero the extruded length again
277 ;Put printing message on LCD screen
279 end4.gcode = ;End GCode
280 M104 T0 S0 ;extruder heater off
281 M104 T1 S0 ;extruder heater off
282 M104 T2 S0 ;extruder heater off
283 M104 T3 S0 ;extruder heater off
284 M140 S0 ;heated bed heater off (if you have it)
285 G91 ;relative positioning
286 G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
287 G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
288 G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
290 G90 ;absolute positioning
292 support_start.gcode =
297 preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
298 ;This code is added before the T(n)
299 postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
300 ;This code is added after the T(n)