resources/quickprint/lulzbot_profiles/Mini_single_extruder_v2/HIPS_high-speed_Mini_single-extruder-v2_0.5noz_cura.ini

   1 [profile]
   2 layer_height = 0.38
   3 wall_thickness = 1.0
   4 retraction_enable = True
   5 solid_layer_thickness = 0.8
   6 fill_density = 20
   7 nozzle_size = 0.5
   8 print_speed = 50
   9 print_temperature = 240
  10 print_temperature2 = 0
  11 print_temperature3 = 0
  12 print_temperature4 = 0
  13 print_bed_temperature = 110
  14 support = None
  15 platform_adhesion = None
  16 support_dual_extrusion = Both
  17 wipe_tower = False
  18 wipe_tower_volume = 15
  19 ooze_shield = False
  20 filament_diameter = 2.85
  21 filament_diameter2 = 0
  22 filament_diameter3 = 0
  23 filament_diameter4 = 0
  24 filament_flow = 100.0
  25 retraction_speed = 10
  26 retraction_amount = 1
  27 retraction_dual_amount = 16.5
  28 retraction_min_travel = 1.5
  29 retraction_combing = All
  30 retraction_minimal_extrusion = 0.005
  31 retraction_hop = 0.1
  32 bottom_thickness = 0.425
  33 layer0_width_factor = 125
  34 object_sink = 0.0
  35 overlap_dual = 0.15
  36 travel_speed = 175
  37 bottom_layer_speed = 15
  38 infill_speed = 70
  39 solidarea_speed = 40
  40 inset0_speed = 40
  41 insetx_speed = 45
  42 cool_min_layer_time = 15
  43 fan_enabled = True
  44 skirt_line_count = 1
  45 skirt_gap = 3.0
  46 skirt_minimal_length = 250
  47 fan_full_height = 0.5
  48 fan_speed = 40
  49 fan_speed_max = 50
  50 cool_min_feedrate = 10
  51 cool_head_lift = False
  52 solid_top = True
  53 solid_bottom = True
  54 fill_overlap = 15
  55 support_type = Lines
  56 support_angle = 45
  57 support_fill_rate = 30
  58 support_xy_distance = 0.7
  59 support_z_distance = 0.05
  60 spiralize = False
  61 simple_mode = False
  62 brim_line_count = 10
  63 raft_margin = 5.0
  64 raft_line_spacing = 3.0
  65 raft_base_thickness = 0.3
  66 raft_base_linewidth = 1.0
  67 raft_interface_thickness = 0.27
  68 raft_interface_linewidth = 0.4
  69 raft_airgap = 0.5
  70 raft_surface_layers = 2
  71 fix_horrible_union_all_type_a = True
  72 fix_horrible_union_all_type_b = False
  73 fix_horrible_use_open_bits = False
  74 fix_horrible_extensive_stitching = False
  75 plugin_config = (lp1
  76         .
  77 object_center_x = -1
  78 object_center_y = -1
  79
  80 [alterations]
  81 start.gcode = ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
  82         ;Print time: {print_time}
  83         ;Filament used: {filament_amount}m {filament_weight}g
  84         ;Filament cost: {filament_cost}
  85         ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
  86         ;M109 S{print_temperature} ;Uncomment to add your own temperature line
  87         G21                          ; metric values
  88         G90                          ; absolute positioning
  89         M82                          ; set extruder to absolute mode
  90         M107                         ; start with the fan off
  91         G92 E0                       ; set extruder position to 0
  92         M140 S110                    ; get bed heating up
  93         G28                          ; home all
  94         M109 S150                    ; set to cleaning temp and wait
  95         G1 Z150 E-30 F75             ; suck up XXmm of filament
  96         M109 S170                    ; heat up rest of way
  97         G1 X45 Y174 F11520           ; move behind scraper
  98         G1 Z0  F1200                 ; CRITICAL: set Z to height of top of scraper
  99         G1 X45 Y174 Z-.5 F4000       ; wiping ; plunge into wipe pad
 100         G1 X55 Y172 Z-.5 F4000       ; wiping
 101         G1 X45 Y174 Z0 F4000         ; wiping
 102         G1 X55 Y172 F4000            ; wiping
 103         G1 X45 Y174 F4000            ; wiping
 104         G1 X55 Y172 F4000            ; wiping
 105         G1 X45 Y174 F4000            ; wiping
 106         G1 X55 Y172 F4000            ; wiping
 107         G1 X60 Y174 F4000            ; wiping
 108         G1 X80 Y172 F4000            ; wiping
 109         G1 X60 Y174 F4000            ; wiping
 110         G1 X80 Y172 F4000            ; wiping
 111         G1 X60 Y174 F4000            ; wiping
 112         G1 X90 Y172 F4000            ; wiping
 113         G1 X80 Y174 F4000            ; wiping
 114         G1 X100 Y172 F4000           ; wiping
 115         G1 X80 Y174 F4000            ; wiping
 116         G1 X100 Y172 F4000           ; wiping
 117         G1 X80 Y174 F4000            ; wiping
 118         G1 X100 Y172 F4000           ; wiping
 119         G1 X110 Y174 F4000           ; wiping
 120         G1 X100 Y172 F4000           ; wiping
 121         G1 X110 Y174 F4000           ; wiping
 122         G1 X100 Y172 F4000           ; wiping
 123         G1 X110 Y174 F4000           ; wiping
 124         G1 X115 Y172 Z-0.5 F1000     ; wipe slower and bury noz in cleanish area
 125         G1 Z10                       ; raise z
 126         G28 X0 Y0                    ; home x and y
 127         M109 S170                    ; set to probing temp
 128         M204 S300                    ; set accel for probing
 129         G29                          ; Probe
 130         M204 S2000                   ; set accel back to normal
 131         G1 X5 Y15 Z10 F5000          ; get out the way
 132         M400                         ; clear buffer
 133         G4 S1                        ; pause
 134         M109 S{print_temperature}    ; set extruder temp and wait
 135         G4 S25                       ; wait for bed to temp up
 136         G1 Z2 E0 F75                 ; extrude filament back into nozzle
 137         M140 S{print_bed_temperature}; get bed temping up during first layer
 138 end.gcode =
 139     M400
 140     M104 S0                                      ; hotend off
 141     M140 S0                                      ; heated bed heater off (if you have it)
 142     M107                                         ; fans off
 143     G92 E5                                       ; set extruder to 5mm for retract on print end
 144     G1 X5 Y5 Z158 E0 F10000                      ; move to cooling positioning
 145     M190 R60                                     ; wait for bed to cool
 146     M140 S0                                      ;
 147     G1 X145 F1000                                ; move to cooling positioning
 148     G1 Y175 F1000                                ; move to cooling positioning
 149     M84                                          ; steppers off
 150     G90                                          ; absolute positioning
 151     ;{profile_string}
 152 start2.gcode = ;Sliced at: {day} {date} {time}
 153         ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
 154         ;Print time: {print_time}
 155         ;Filament used: {filament_amount}m {filament_weight}g
 156         ;Filament cost: {filament_cost}
 157         ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
 158         ;M104 S{print_temperature} ;Uncomment to add your own temperature line
 159         ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
 160         ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
 161         G21        ;metric values
 162         G90        ;absolute positioning
 163         M107       ;start with the fan off
 164         G28 X0 Y0  ;move X/Y to min endstops
 165         G28 Z0     ;move Z to min endstops
 166         G1 Z15.0 F{travel_speed} ;move the platform down 15mm
 167         T1                      ;Switch to the 2nd extruder
 168         G92 E0                  ;zero the extruded length
 169         G1 F200 E10             ;extrude 10mm of feed stock
 170         G92 E0                  ;zero the extruded length again
 171         G1 F200 E-{retraction_dual_amount}
 172         T0                      ;Switch to the first extruder
 173         G92 E0                  ;zero the extruded length
 174         G1 F200 E10             ;extrude 10mm of feed stock
 175         G92 E0                  ;zero the extruded length again
 176         G1 F{travel_speed}
 177         ;Put printing message on LCD screen
 178         M117 Printing...
 179 end2.gcode = ;End GCode
 180         M104 T0 S0                     ;extruder heater off
 181         M104 T1 S0                     ;extruder heater off
 182         M140 S0                     ;heated bed heater off (if you have it)
 183         G91                                    ;relative positioning
 184         G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
 185         G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
 186         G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way
 187         M84                         ;steppers off
 188         G90                         ;absolute positioning
 189         ;{profile_string}
 190 start3.gcode = ;Sliced at: {day} {date} {time}
 191         ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
 192         ;Print time: {print_time}
 193         ;Filament used: {filament_amount}m {filament_weight}g
 194         ;Filament cost: {filament_cost}
 195         ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
 196         ;M104 S{print_temperature} ;Uncomment to add your own temperature line
 197         ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
 198         ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
 199         G21        ;metric values
 200         G90        ;absolute positioning
 201         M107       ;start with the fan off
 202         G28 X0 Y0  ;move X/Y to min endstops
 203         G28 Z0     ;move Z to min endstops
 204         G1 Z15.0 F{travel_speed} ;move the platform down 15mm
 205         T2                      ;Switch to the 2nd extruder
 206         G92 E0                  ;zero the extruded length
 207         G1 F200 E10             ;extrude 10mm of feed stock
 208         G92 E0                  ;zero the extruded length again
 209         G1 F200 E-{retraction_dual_amount}
 210         T1                      ;Switch to the 2nd extruder
 211         G92 E0                  ;zero the extruded length
 212         G1 F200 E10             ;extrude 10mm of feed stock
 213         G92 E0                  ;zero the extruded length again
 214         G1 F200 E-{retraction_dual_amount}
 215         T0                      ;Switch to the first extruder
 216         G92 E0                  ;zero the extruded length
 217         G1 F200 E10             ;extrude 10mm of feed stock
 218         G92 E0                  ;zero the extruded length again
 219         G1 F{travel_speed}
 220         ;Put printing message on LCD screen
 221         M117 Printing...
 222 end3.gcode = ;End GCode
 223         M104 T0 S0                     ;extruder heater off
 224         M104 T1 S0                     ;extruder heater off
 225         M104 T2 S0                     ;extruder heater off
 226         M140 S0                     ;heated bed heater off (if you have it)
 227         G91                                    ;relative positioning
 228         G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
 229         G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
 230         G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way
 231         M84                         ;steppers off
 232         G90                         ;absolute positioning
 233         ;{profile_string}
 234 start4.gcode = ;Sliced at: {day} {date} {time}
 235         ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
 236         ;Print time: {print_time}
 237         ;Filament used: {filament_amount}m {filament_weight}g
 238         ;Filament cost: {filament_cost}
 239         ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
 240         ;M104 S{print_temperature} ;Uncomment to add your own temperature line
 241         ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
 242         ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
 243         ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
 244         G21        ;metric values
 245         G90        ;absolute positioning
 246         M107       ;start with the fan off
 247         G28 X0 Y0  ;move X/Y to min endstops
 248         G28 Z0     ;move Z to min endstops
 249         G1 Z15.0 F{travel_speed} ;move the platform down 15mm
 250         T3                      ;Switch to the 4th extruder
 251         G92 E0                  ;zero the extruded length
 252         G1 F200 E10             ;extrude 10mm of feed stock
 253         G92 E0                  ;zero the extruded length again
 254         G1 F200 E-{retraction_dual_amount}
 255         T2                      ;Switch to the 3th extruder
 256         G92 E0                  ;zero the extruded length
 257         G1 F200 E10             ;extrude 10mm of feed stock
 258         G92 E0                  ;zero the extruded length again
 259         G1 F200 E-{retraction_dual_amount}
 260         T1                      ;Switch to the 2nd extruder
 261         G92 E0                  ;zero the extruded length
 262         G1 F200 E10             ;extrude 10mm of feed stock
 263         G92 E0                  ;zero the extruded length again
 264         G1 F200 E-{retraction_dual_amount}
 265         T0                      ;Switch to the first extruder
 266         G92 E0                  ;zero the extruded length
 267         G1 F200 E10             ;extrude 10mm of feed stock
 268         G92 E0                  ;zero the extruded length again
 269         G1 F{travel_speed}
 270         ;Put printing message on LCD screen
 271         M117 Printing...
 272 end4.gcode = ;End GCode
 273         M104 T0 S0                     ;extruder heater off
 274         M104 T1 S0                     ;extruder heater off
 275         M104 T2 S0                     ;extruder heater off
 276         M104 T3 S0                     ;extruder heater off
 277         M140 S0                     ;heated bed heater off (if you have it)
 278         G91                                    ;relative positioning
 279         G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
 280         G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
 281         G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way
 282         M84                         ;steppers off
 283         G90                         ;absolute positioning
 284         ;{profile_string}
 285 support_start.gcode =
 286 support_end.gcode =
 287 cool_start.gcode =
 288 cool_end.gcode =
 289 replace.csv =
 290 preswitchextruder.gcode = ;Switch between the current extruder and the next ex
 291 postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
 292         ;This code is added after the T(n)
 293