3 // Hard case for Fairphone 2
5 // Copyright 2018 Ian Jackson. There is NO WARRANTY.
6 // See below for full licensing and disclaimer.
10 // 1. You will want to git clone this repository.
12 // 2. Decide about the notification LED aperture. See the variable
13 // led_window_style, below. The default here is "ad-hoc
14 // multi-colour", which can produces a translucent (clear-ish)
15 // window set into the lid, even on a single-nozzle printer.
16 // See "Ad-hoc multi-colour", below.
18 // 3. use "make" to generate the necessary files:
20 // make -j8 fairphone-case.auto.scads `for f in \
26 // ; do echo fairphone-case,$f.auto.stl; done`
28 // 4. Print them. Case and OneKeeperPrint should probably be
31 // For Lid and LidWindowPrint, if you are doing ad-hoc
33 // i. Set up for clear filament
34 // ii. Print LidWindowPrint. Wait for it to finish.
35 // It won't take long. As soon as it finishes, tell
36 // your printer to warm up (so that in fact it does
38 // iii. Leaving the output so far on the printbed, reload
39 // your printer with the main lid colour.
40 // iv. Print LidPrint. You can let this go unattended.
42 // 5. Assemble the hinge. You will need 4x M2 12mm machine screws
43 // and 8x M2 full nuts.
45 // Make sure you get the hinge the right way round. If you're not
47 // openscad fairphone-case,DemoHinge.auto.scad
48 // to see an assembly diagram.
50 // The nuts recess into the hinge. You will want very fine
51 // pliers. As you screw each screw in, add the second nut when
52 // the screw thread emerges from the first - this will be a
53 // locknut. Screw each screw to an appropriate tightness for the
54 // hinge stiffness. You want the lid-side hinge to be stiffer as
55 // that makes closing the case work better.
57 // When you have the stiffness right, tighten the locknuts onto
62 // - To put the phone in, drop its RH side into the RH side of
63 // the case. Then feed the keeper through the small hole.
64 // Feed it right through.
66 // - The optional prop can be used to prop the phone up (in
67 // portrait orientation only right now). See
68 // openscad fairphone-case,DemoPropAngles.auto.scad
70 // Ad-hoc multi-colour
72 // This file is set up to let you make a translucent window using a
73 // single-extruder printer, using a "two print run" technique. This
74 // works well with our Lulzbot TAZ 5 and Aleph Objects' version of
75 // Cura. If you are using a different printer, you may need to
76 // adjust the parameters or try a different technique. In particular,
77 // initial_layer_thick
78 // set so that the window is one layer thick
79 // initial_layer_width
80 // set so that the slicer draws a rectangle around the whole
81 // object, rather than putting a "skirt" or anything inside
83 // If you have a dual-extruder printer, you can set led_window_style
84 // to 2 and do a single print of LidPrint and LidWindowPrint.
86 // Alternatively you can set it to 1 (just a hole) or 0 (no hole).
88 // Thanks to Clare Boothby for the ad-hoc multi-colour technique (and
89 // the parameters for our Lulzbot TAZ 5 and Aleph Objects's Cura).
93 // It might well be possible to adapt this file for other phones.
94 // If you do, let me know how you get on.
97 // AUTHORSHIP, COPYRIGHT, LICENCE, AND LACK OF WARRANTY
99 // Copyright (C)2018 Ian Jackson.
101 // This program for generating a 3D model is free software: you can
102 // redistribute it and/or modify it under the terms of the GNU
103 // General Public License as published by the Free Software
104 // Foundation, either version 3 of the License, or (at your option)
105 // any later version.
107 // This program is distributed in the hope that it will be useful,
108 // but WITHOUT ANY WARRANTY; without even the implied warranty of
109 // MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
110 // GNU General Public License for more details.
112 // You should have received a copy of the GNU General Public
113 // License along with this program. If not, see
114 // <http://www.gnu.org/licenses/>.
116 // In particular DO NOT BLAME ME IF THIS CASE DOES NOT ADEQUATELY
117 // PROTECT YOUR PHONE ! It is your responsibility to decide whether
118 // this case will meet your needs.
123 phone = [ 75.0, 145.0 ];
125 prop_buildout_less = 3;
127 prop_angles = [ 15, 30, 45, 60 ];
129 bumper = [ 0.250, -0.025 ];
130 // ^ One side. Overall size is increased by twice this.
131 // If no bumpers, is the gap around the phone.
135 led_window_style = 3;
137 // 1: simply an opening
138 // 2: opening with separate cover model, for printing in clear (two colour)
139 // 3: like 2 but one-layer window for ad-hoc multi-colour
141 initial_layer_thick = 0.400; // ^ needed for mode 3 only
142 initial_layer_width = 0.750; // ^ needed for mode 3 only
143 multicolour_gap = 0.15; // each side
146 phone_rim_depth = 0.80; // includes allowance for a screen protector
148 button_cutout_depth = 9;
150 phone_edge_thick = 9.0;
151 phone_total_thick = 12.0;
152 phone_backside_slope_inner = 1.5; // larger means shallower
153 phone_backside_slope_outer = 1.0; // larger means shallower
155 camera_pos_tl = [ 6.450, 12.750 ]; // measured from tl corner
156 camera_pos_br = [ 22.300, 37.600 ]; // tl/br as seen from back
158 jack_pos = [ 13.83, 8.485 ];
159 jack_dia = 10.64 + .5; // some jack I had lying around
161 led_pos = [ 13.98, 10.00 ];
163 led_window_ledge = 0.75; // each side
165 noisecancelmic_pos = [ 19.54, 7.37 ]; // from rhs
166 noisecancelmic_dia = 4.00;
168 //fingerpushhole_dias = [ 15, 18 ];
169 fingerpushhole_dias = [];
171 lanyard_half_dia = 1.15;
172 lanyard_entry_rel_breadth = 2;
173 lanyard_channel_len = 15;
174 rearspeaker_pos_bl = [ 12.64, 18.72 ];
175 rearspeaker_size = [ 3.76, 7.36 ];
177 microusb_above = 3.27 - 0.25;
178 microusb_below = 0.0;
179 microusb_width = 16.12 + 1.25;
181 case_th_bottom = 2.5;
186 lid_screen_gap_extra = .66;
188 case_struts_count = 6;
189 case_struts_solid_below = 1.00;
190 case_struts_solid_above = 0.75;
191 case_struts_width = 0.10;
195 keeper_inner_width = 2.75;
196 keeper_inner_height = 2.75;
197 keeper_slant_slope = 2; // larger means steeper
199 keeper_gap_z_top = 0.25;
200 keeper_gap_z_bot = 0.75;
202 keeper_gap_x_holes = 0.75;
204 keeper_side = 0; // 0 = lhs; 1 = rhs
211 lid_edgepart_width = 5.0;
212 lid_buttoncover_thick = 1.3;
213 lid_buttoncover_reinf = 0.65;
216 foldover_lever_gap = 0.50;
218 // properties of the hinge fasteners
219 hingescrew_shaft_dia = 2.0 + 0.25; // M2 x 12mm machine screw
220 hingescrew_shaft_len = 12;
221 hingescrew_fasteners_extra_thick = 0.40;
222 // ^ amount of thread protruding if everything was completely nominal
223 // and we are using two nuts
224 hingescrew_nut_access_dia = 4.72 + 0.50;
225 // ^ washer is 4.72 dia
226 // also, want to get pliers or tiny spanner in to do up locknut
227 hingescrew_nut_across = 3.92 + 0.25; // incl. slop around recess slop
228 hingescrew_nut_thick = 1.93;
229 hingescrew_head_th = 1.38 + 0.75;
230 hingescrew_head_dia = 3.92;
232 hingescrew_nut_recess_portion = 2/3; // portion of nut in recess
234 lever_cover_th = 0.75;
236 hingemount_wd = 4.8725;
241 button_l_fudge = 4.4;
242 buttonishleg_default_l_is_fudge = 10;
244 hinge_base_slope = 1.5; // bigger is steeper
246 strut_min_at_end = 1.5;
249 hinge_x_postscrew_gap = 0.75;
250 hinge_x_arms_gap = 0.35;
251 hinge_r_arms_gap = 0.55;
253 rearspeaker_gap = [ 2.0, 2.0 ]; // each side
255 thumbrecess_depth = 1.3;
261 catch_thickness = 1.3;
262 catch_side_gap = 0.75; // each side
266 catch_finger_height = 1.5;
267 catch_finger_depth = 2.5;
268 catch_catch_slope = 2.00;
269 catch_close_slope = 3.00;
271 catch_topcurve_r = 5.0;
273 prop_recess_under = 0.50;
274 prop_recess_slop = 0.200; // each side
279 prop_side_gap = 0.75; // each side
280 prop_lidrecess_behind = 0.75;
281 prop_caserecess_behind = 0.75;
282 prop_caserecess_taper = 0.45; // one side only
284 prop_prong_heel_slope = 0.5;
286 lid_fold_clearance_antislop = 0.5;
288 // ---------- calculated ----------
290 phone_width = (phone + bumper*2)[0];
291 phone_height = (phone + bumper*2)[1];
293 inside_br = [phone_width, -phone_height];
295 prop_prong_h = prop_main_th;
297 //echo(camera_pos_tl + bumper,
298 // camera_pos_br + bumper);
300 // ----- could be changed -----
301 lid_buttoncover_gap = lid_gap_x;
302 lid_buttoncover_overlap = case_th_lip + keeper_gap_z_top;
304 phone_backside_slope_thick = phone_total_thick - phone_edge_thick;
306 //prop_lidrecess_depth = case_th_lid - prop_recess_under;
308 //prop_nose_len = case_th_lid - prop_recess_under;
309 //prop_recess_slope = tan(prop_max_angle); // bigger means steeper
310 //prop_recess_width = prop_main_th / cos(prop_max_angle) + prop_backfwd_gap;
313 //lid_lip_overlap_width xxx bad name = ;
314 //lid_lip_inner_slope = [ 5, 5 ]; // xxx
317 epp1 = [0, -phone_edge_thick];
318 epp2i = epp1 + phone_backside_slope_thick * [ phone_backside_slope_inner, -1 ];
319 epp2o = epp1 + phone_backside_slope_thick * [ phone_backside_slope_outer, -1 ];
320 epp3 = epp2i + [10, 0];
321 epp5 = epp0 + [0,1] * (keeper_th_z + keeper_gap_z_top + case_lip);
322 epp4 = epp5 + [-1,0] * case_th_side;
325 kppd = kppe + [1,0] * keeper_inner_width;
326 kppc = kppd + [0,1] * keeper_th_z;
327 kppb = [ kppe[0] - keeper_th_x, kppc[1] ];
328 kppf = kppe - [0,1] * keeper_inner_height;
329 kppa = [ kppb[0], kppf[1] ];
331 lpp10 = [ epp5[0] + lid_gap_x, kppc[1] + lid_gap_z ];
332 lpp11 = [ lpp10[0], epp5[1] + lid_gap_z ];
334 lpp14 = lpp10 + [1,0] * max(keeper_inner_width, lid_edgepart_width);
335 // exact x posn not very important; must extend past end of keeper
338 epp0[1] - phone_rim_depth + 1/2.5 * case_th_lid
339 + lid_screen_gap_extra ];
340 // ^ beam theory says to maximise force before contact,
341 // the gap below the `beam' (the lid) must be 1/3
342 // the thickness (ie the lid thickness) if the beam
343 // is solid, or 1/2 if it has a top and bottom only.
344 // ours is mostly solid.
346 lp_r12 = max(case_th_lid - (lpp11[1] - lpp15[1]),
349 lpp12 = [ epp4[0] + lp_r12, lpp11[1] ];
350 lpp13 = [ lpp12[0], lpp12[1] + lp_r12 ];
352 case_bottom_z = epp2o[1] - case_th_bottom;
356 bppN = [ bppM[0] + lid_buttoncover_thick, bppM[1] ];
357 bppR = [ bppN[0] + lid_buttoncover_gap, -button_cutout_depth ];
358 bppS = [ epp1[0], bppR[1] ];
359 bppQ = [ bppM[0], bppR[1] - lid_buttoncover_overlap ];
360 bppP = bppQ + [0,1] * lid_buttoncover_gap;
361 bppO = [ bppN[0], bppP[1] ];
362 bppL = lpp10 + [5,0];
363 bppK = [ bppL[0], bppN[1] ];
364 bppJ = [ bppN[0], bppL[1] ];
365 bppU = [ bppJ[0], lpp12[1] ];
369 echo("BUTTON COVER TH", bppO[0] - bppP[0]);
371 // notification led aperture
373 nla_r0 = led_aperture/2;
374 nla_r1 = nla_r0 + led_window_ledge;
375 nla_r2 = nla_r1 + multicolour_gap;
377 led_window_style >= 3 ? initial_layer_thick :
378 led_window_style >= 2 ? led_window_ledge : 0;
382 hp_rn = hingescrew_nut_access_dia/2;
383 hp_r2_min = hp_rn + lever_cover_th;
384 hp_rs = hingescrew_shaft_dia/2;
385 hp_r1_min = hp_rs + hingemount_th;
387 hp_r1 = max(hp_r1_min, hp_r2_min);
391 hppS = epp2o + [0,-1] * case_th_bottom;
392 hp_k = 0.5 * (hppU[1] - hppS[1] + foldover_gap);
394 hppM = [ epp4[0] - foldover_lever_gap - hp_r2,
395 0.5 * (hppU + hppS)[1] ];
396 hppT = [ hppM[0], hppU[1] - hp_r1 ];
397 hppB = hppT + [0,-1] * hp_k;
399 hppE_y = epp2o[1] - case_th_bottom + hp_r1;
400 hppE_x = hppB[0] + (hppB[1] - hppE_y) * hinge_base_slope;
401 hppE = [ hppE_x, hppE_y ];
403 // hinge elevation x coords
405 hex20 = max(epp2o[0],
407 kppd[0] + hingescrew_head_th + keeper_gap_x_holes);
408 hex21 = hex20 + hingemount_wd;
409 hex22 = hex21 + hinge_x_gap;
410 hex27 = hex20 + hingescrew_shaft_len;
411 hex24 = hex27 + hinge_x_postscrew_gap;
412 hex23 = hex27 - (hingescrew_nut_thick*2
413 + hingescrew_fasteners_extra_thick);
414 hex26 = hex23 + hingescrew_nut_thick * 2/3;
416 echo(hex20, hex21, hex22, hex23, hex24);
417 // 6, 10.8725, 10.9975, 13.74, 18.75
418 module chk(act,exp) {
419 if (abs(act-exp) > 1e-9) echo("WRONG", act, exp);
420 else echo("ok", act);
428 lid_fold_clearance_skew =
429 (lpp10[1] - hppB[1]) /
430 (lpp10[0] - hppB[0]);
432 echo("SK",lid_fold_clearance_skew);
434 // thumb recess (used to be "catch" hence cpp*
436 cppA = epp4 + [thumbrecess_depth, 0];
437 cppB = [ cppA[0], epp1[1] ];
441 ly_r = lanyard_half_dia / 2;
444 ly_theta = -atan2vector(epp2i - epp1);
445 ly_o = epp2i + 3 * ly_r * unitvector2d(epp1 - epp2i);
447 max_case_bottom_edge_thickness =
449 + sin(ly_theta) * (epp2i-epp2o)[0];
451 ly_q_z = -(ly_rc + ly_r);
452 ly_re = max_case_bottom_edge_thickness - (-ly_q_z);
454 ly_oec_y = lanyard_entry_rel_breadth * ly_r;
456 // prop recess in case
458 prop_x_pos = phone_width/2;
460 prop_recess_hw = 0.5 * prop_main_width + prop_side_gap;
462 prc_r1 = prop_end_dia/2;
463 prc_r3 = prc_r1 + prop_recess_slop;
465 prcp2 = [ epp4[0] + prop_buildout_less,
468 prop_caserecess_buildout_r = -1; // prcp2[0] - epp2o[0];
470 prcp1 = [ epp2o[0] + prc_r3 + prop_caserecess_behind,
471 epp2i[1] - prc_r3 - prop_recess_under];
473 // prop recess in lid
475 prl_r10 = prop_end_dia/2;
476 prl_r10o = prl_r10 + prop_recess_slop;
478 prlp10 = lpp10 + [1,1] * prl_r10o
479 + [1,0] * prop_lidrecess_behind
480 + [0,1] * prop_recess_under;
485 $prpp11 = [0, prop_taper_len];
489 // ---------- modules ----------
491 module AdhocMultiprintFrame(phase, z0, zs) {
492 // from z0 to z0 + zs*layer
493 extra = phase * (initial_layer_width + multicolour_gap) + 5;
494 xextra = extra + -epp4[0];
495 xrange = [ 0, phone_width ] + [-1,+1] * xextra;
496 yextra = extra + -epp4[0];
497 yrange = [ -phone_height + +hppB[0] - hp_r2, 0 ] + [-1,+1] * yextra;
498 p0 = [ xrange[0], yrange[0] ];
499 p1 = [ xrange[1], yrange[1] ];
502 mirror([0,0, zs<0 ? 1 : 0])
503 linear_extrude(height= initial_layer_thick)
505 rectfromto(p0 - [1,1] * initial_layer_width,
506 p1 + [1,1] * initial_layer_width);
511 module KeeperProfile(slant=0){
512 use_e = kppe + [0,-1] * slant * keeper_inner_width / keeper_slant_slope;
513 polygon([use_e, kppd, kppc, kppb, kppa, kppf]);
516 module EdgeProfile(){
519 translate(epp3) square(case_th_bottom*2, center=true);
520 circleat(epp2o, r=case_th_bottom);
521 circleat(epp1, r=case_th_side);
522 rectfromto(epp0, epp4);
524 polygon([ epp5 + [0,10],
531 module LanyardLanyardProfile(entry=false){
533 for (xs=[-1,+1] * (entry ? lanyard_entry_rel_breadth : 1))
534 translate(xs * 0.5 * lanyard_half_dia * [1,0])
535 circle(r= lanyard_half_dia/2);
539 module LanyardCurveChannelProfile(){
540 translate([0, -ly_r])
541 LanyardLanyardProfile();
544 module LanyardEntryChannelProfile(){
545 LanyardLanyardProfile(true);
548 module LanyardMainChannelProfile(){
549 LanyardCurveChannelProfile();
551 square(center=true, ly_r * [6, 2]);
553 translate(ly_r * [3 * xs, -1])
558 module LanyardEntryOuterProfile(){
559 circleat([ly_re + ly_r, 0], ly_re);
562 module LanyardEntry(){
568 translate([d_x, 0, q_z]) {
571 rotate_extrude(convexity=10)
574 LanyardCurveChannelProfile();
582 linear_extrude(height=20)
584 LanyardEntryChannelProfile();
586 translate([0, ly_r*2, 0])
588 linear_extrude(height = ly_r*4){
590 rectfromto([d_x, q_z], [ly_r, 0]);
591 circleat([d_x, q_z], ly_rc);
595 translate([0,0,q_z]){
598 translate([0, oec_y, 0]){
600 translate(ly_re * [-1,0,-2])
601 cube(ly_re * [2,1,2]);
602 rotate_extrude(convexity=10)
603 LanyardEntryOuterProfile();
608 translate([-ly_re, -(oec_y + 0.01), -2*ly_re])
609 cube([ly_re*2, 2*(oec_y + 0.01), 2*ly_re]);
614 linear_extrude(height=20)
615 LanyardEntryOuterProfile();
620 module LanyardCutout(l){
622 linear_extrude(height=l)
624 LanyardMainChannelProfile();
627 translate(ee * l * [-1,0])
633 module LidEdgeProfile(){
644 circleat(lpp12, r=lp_r12);
645 rectfromto( lpp12 + [-10, 0],
646 lpp12 + [+10, +10] );
650 module LidEdgeFoldClearanceProfile(){
651 translate([-lid_fold_clearance_antislop, 0])
660 module ButtonCoverProfile(){
662 polygon(concat([ bppM, bppP, bppO, bppJ ],
663 (enable_support && !$button_suppress_over_keeper
664 ? [ bppU, bppV, bppW ] : []),
673 module ButtonPlan(l, deep, cut){
675 (cut ? 0 : lid_buttoncover_gap);
678 (deep ? lid_buttoncover_overlap : 0);
680 C = [0,0]; // by definition
684 B0 = C + [0,-1] * button_cutout_depth;
685 B1 = B0 + [0,1] * epsilon;
687 r0 = 0.5 * (T[1] - B0[1]);
688 A = [ -(l + button_l_fudge)/2 + r0, 0.5 * (T[1] + B0[1]) ];
689 H = A + [0,-1] * delta;
695 E1 = E0 + [1,0] * epsilon;
697 I0 = [ E0[0], H[1] ];
698 I1 = [ E1[0], H[1] ];
701 for (m=[0,1]) mirror([m,0])
702 circleat(H, r0 - epsilon);
704 for (m=[0,1]) mirror([m,0]) {
714 circleat(D, r0 + epsilon);
719 module ButtonCoverReinf(){ ////toplevel
722 linear_extrude(height=0.01)
724 ButtonCoverProfile();
725 translate([bppJ[0] + 0.1, -50]) mirror([1,0])
728 mirror([0,0,1]) linear_extrude(height=0.01) intersection(){
729 circle(r= lid_buttoncover_reinf);
730 translate([-20,0]) square(40, center=true);
735 module CatchCutProfile(){
737 polygon([ cppA + [-10,0],
741 circleat(epp1, r=case_th_side);
745 module Flip_rhs(yn=[0,1]) {
747 translate([phone_width/2, 0, 0])
748 mirror([$rhsflip,0,0])
749 translate([-phone_width/2, 0, 0])
754 module Flip_bot(yn=[0,1]) {
756 translate([0, -phone_height/2, 0])
757 mirror([0, $botflip, 0])
758 translate([0, phone_height/2, 0])
763 module AroundEdges(fill_zstart, fill_th, fill_downwards=0){
766 translate([0, -phone_cnr_rad, 0])
768 linear_extrude(height = phone_height - phone_cnr_rad*2)
772 Flip_rhs() Flip_bot() {
773 translate([+1,-1] * phone_cnr_rad)
778 translate([-1,0] * phone_cnr_rad)
780 rectfromto([0,-20],[10,20]);
782 translate([-10, 0, -20] + 0.01 * [+1,-1, 0] )
788 translate([ phone_width - phone_cnr_rad, 0,0 ])
790 linear_extrude(height = phone_width - phone_cnr_rad*2)
794 translate([0,0, fill_zstart])
795 mirror([0,0, fill_downwards])
796 linear_extrude(height = fill_th)
797 rectfromto([+1,-1] * phone_cnr_rad,
798 [phone_width, -phone_height] + [-1,+1] * phone_cnr_rad);
801 module CaseAperture(pos, dia, $fn) {
803 translate([ pos[0] + bumper[0],
806 rotate([-90, theta, 0])
807 cylinder(r = dia/2 / cos(theta),
811 module SideButton(y, y_ref_sign, l, suppress_over_keeper=0){
813 // +1 measured from top of actual phone to top of button
814 // -1 measured from bottom of actual phone to bottom of button
815 // 0 y is centre of button in coordinate system
817 $button_suppress_over_keeper= suppress_over_keeper;
818 eff_y = y_ref_sign > 0 ? -bumper [1] -y -l/2 :
819 y_ref_sign < 0 ? (-phone -bumper)[1] +y +l/2 :
822 translate([0, eff_y, 0])
826 module LidButtonishLeg(y, y_ref_sign, l=buttonishleg_default_l_is_fudge) {
827 $button_leg_only = true;
828 SideButton(y, y_ref_sign, l) children();
832 Flip_rhs(1) SideButton(15.580, +1, 8.9 ) children(); // power
833 Flip_rhs(1) SideButton(48.700, -1, 8.920 ) children(); // camera
834 Flip_rhs(0) SideButton(30.800, +1, 21.96, 1) children(); // volume
835 Flip_rhs( ) LidButtonishLeg(14, -1) children();
836 // Flip_rhs(0) LidButtonishLeg(20, +1, 20) children();
839 module Struts(x_start, z_min, th){
840 // if th is negative, starts at z_min and works towards -ve z
841 // and object should then be printed other way up
842 for (i= [1 : 1 : case_struts_count]) {
846 mirror([0,0, th<0 ? 1 : 0])
848 -phone_height * i / (case_struts_count+1),
849 case_struts_solid_below])
850 linear_extrude(height= abs(th)
851 -(case_struts_solid_below+case_struts_solid_above))
852 rectfromto([ x_start, -0.5 * case_struts_width ],
853 [ phone_width - x_start, +0.5 * case_struts_width ]);
857 module OrdinaryRearAperture(rhs,bot, pos){
858 Flip_rhs(rhs) Flip_bot(bot)
861 translate(pos + bumper)
869 linextr(-epp2i[0], 60)
870 translate([0.5 * phone_width, 0, 0])
871 rectfromto([-microusb_width/2, epp2i[1] + microusb_below],
872 [+microusb_width/2, epp0[1] + -microusb_above]);
876 module OrdinaryRearApertures(){
878 OrdinaryRearAperture(1,1, rearspeaker_pos_bl)
879 rectfromto(-rearspeaker_gap,
880 rearspeaker_size + rearspeaker_gap);
882 // finger hole to remove phone
883 if (len(fingerpushhole_dias))
884 OrdinaryRearAperture(1,0, [ fingerpushhole_dias[0]/2 + epp2i[0],
886 scale(fingerpushhole_dias)
890 module RearCameraAperture(){
893 linear_extrude(height = 20)
896 rectfromto(camera_pos_tl, camera_pos_br);
899 module HingeLidProfile(){
901 circleat(hppT, hp_r1);
902 circleat(lpp12, lp_r12);
910 module HingeBaseProfile(){
913 circleat(hppB, hp_r1);
914 circleat(hppE, hp_r1);
915 circleat(epp2o, case_th_bottom);
916 circleat(hppB + [10,0], hp_r1);
918 polygon([epp5, epp1, epp2i, epp3, bppL]);
922 module HingeLeverOuterProfile(){
924 circleat(hppT, hp_r2);
925 circleat(hppB, hp_r2);
929 module HingeLeverInnerProfile(){
931 c = s > 0 ? hppT : hppB;
934 rotate(s<0 ? -40 : 0)
943 module HingeLeverNutProfile(){
944 for (c= [hppB, hppT]) {
946 circle($fn=6, r= 0.5 * hingescrew_nut_across / cos(30));
950 module Flip_hinge(doflip=1){
951 hinge_origin = [0, -(phone_height - hppB[0]), hppB[1]];
952 translate(hinge_origin)
953 rotate([doflip*180,0,0])
954 translate(-hinge_origin)
958 module HingePortion(x0,x1){
959 Flip_rhs() Flip_bot(1)
963 linear_extrude(height=x1-x0)
967 module CatchPortion(ztop){
968 xwidth = catch_side_gap*2;
969 width = catch_width + xwidth;
970 w = width + catch_topcurve_r*2 + 1;
971 translate([phone_width/2, 0,0]){
976 translate([0, 50, 0])
978 linear_extrude(height=100){
979 for (m=[0,1]) mirror([m,0,0]) {
981 translate([w/2, ztop - catch_topcurve_r])
982 circle(catch_topcurve_r);
983 translate([w/2, -50])
984 square(catch_topcurve_r*2, center=true);
993 AroundEdges(epp3[1], case_th_bottom, 1)
997 function prop_x(gamma) = hp_k / (2 * sin(gamma/2)) - hppT[0];
999 module PropProfileAssignments(gamma){
1000 // https://en.wikipedia.org/wiki/Solution_of_triangles#Two_sides_and_the_included_angle_given_(SAS)
1002 p = phone_height + prlp10[0] - hppB[0];
1005 q = phone_height - hppT[0] - prcp1[0]; // $prpp7[0] is 0 by definition
1007 c = sqrt(a*a + b*b - 2*a*b*cos(gamma));
1008 $prp_alpha = acos( (b*b + c*c - a*a) / (2*b*c) );
1010 $prp_theta = 90 - $prp_alpha;
1011 beta = 180 - $prp_alpha - gamma;
1014 //echo("abc", a,b,c);
1016 v1 = [ [ cos(psi), -sin(psi) ], // x
1017 [ sin(psi), cos(psi) ] ]; // y
1019 $prpp7 = [0, c + (lpp13[1] - $prpp10[1] - hp_k) ];
1022 $prp_r11 = prop_main_th/2;
1024 $prpp1 = $prpp7 + [1,0] *
1025 // this is approximate, but will do
1026 (prop_main_th/2 + prop_prop_gap + prcp1[0] - cppA[0]);
1029 v1[1] * ((prcp2[1] - prcp1[1]) - prop_prop_gap);
1030 $prpp12 = $prpp3 + v1[0] *
1031 (prop_end_dia + prop_caserecess_taper * ($prpp1[1] - $prpp3[1]));
1032 $prp_r8 = prop_main_th;
1033 $prpp4 = [ prop_main_th/2, $prpp3[1] ];
1035 $prpp5 = [ $prpp12[0] - $prp_r5,
1036 $prpp3[1] - prop_prong_h + $prp_r5 ];
1037 $prpp6 = $prpp4 + [0,-1] * (prop_prong_h +
1038 prop_prong_heel_slope * ($prpp5[0] - $prpp4[0]));
1039 $prpp8 = $prpp4 + [0,-1] * $prp_r8;
1040 $prpp9 = $prpp8 + [-1,0] * $prp_r8;
1045 module PropProfile(gamma, cut=0, rot=0){
1046 PropProfileAssignments(gamma){
1048 //#circleat($prpp3,1);
1049 //#circleat($prpp12,1);
1056 polygon([[-20,-0], [20,20], [0,0]]);
1058 rectfromto($prpp6, $prpp9);
1059 translate($prpp5) intersection(){
1061 polygon([[-10,-10], [0,0], [10,0]]);
1063 rectfromto($prpp12 + [0,-0.1], $prpp3);
1066 circleat($prpp1, $prp_r1);
1067 rectfromto($prpp12 + [0,-0.1], $prpp3);
1071 rotate([0,0, rot*-$prp_theta]){
1073 extra = cut ? prop_recess_slop : 0;
1074 rectfromto($prpp6, $prpp9);
1075 circleat($prpp11, $prp_r11 + extra);
1076 circleat($prpp10, $prp_r10 + extra);
1082 module PropAggregateProfile(){
1083 for (angle = prop_angles)
1084 PropProfile(angle, 0,0);
1087 module Prop(){ ////toplevel
1088 hw = prop_main_width/2;
1090 PropAggregateProfile();
1093 module Case(){ ////toplevel
1098 // ledge (fixed keeper)
1099 Flip_rhs(1-keeper_side) intersection(){
1101 linear_extrude(height = phone_height + phone_cnr_rad * 2)
1104 // outline of the whole case, to stop it protruding
1105 translate([0,0, -25])
1106 linear_extrude(height = 50)
1109 circleat([+1,-1] * phone_cnr_rad, phone_cnr_rad + case_th_side/2);
1113 HingePortion(hex20, hex21) HingeBaseProfile();
1115 // buildout for prop recess
1116 if (prop_caserecess_buildout_r > 0) Flip_rhs(1)
1117 linextr(case_bottom_z, epp2i[1])
1120 circleat([ prop_x_pos + dxs * prop_caserecess_buildout_r,
1122 r = epp2o[0] - prcp2[0]);
1127 Flip_rhs(keeper_side)
1128 translate([0, -phone_cnr_rad, 0])
1130 linear_extrude(height = phone_height + phone_cnr_rad * 2)
1133 rectfromto([ -keeper_gap_x, -keeper_gap_z_bot ],
1134 [ keeper_gap_x_holes, +keeper_gap_z_top ]);
1138 RearCameraAperture();
1140 // struts (invisible, because they're buried in the case)
1141 Struts(epp2i[0], epp2i[1] - case_th_bottom, case_th_bottom);
1146 if (!($button_leg_only && enable_support))
1148 translate([0,0,-10])
1149 linear_extrude(height= 20)
1150 ButtonPlan($button_l, 0,1);
1151 if ($button_leg_only)
1153 translate([phone_width/2, -400, kppe[1]])
1154 mirror([1-abs($rhsflip - keeper_side),0,0])
1155 cube([400, 800, 50]);
1156 if (enable_support && !$button_suppress_over_keeper)
1158 translate([-400, -400, kppd[1]])
1160 cube([800,800,100]);
1162 translate([0,0, -bppR[0]])
1163 linear_extrude(height= 20)
1164 ButtonPlan($button_l, 1,1);
1169 // apertures along top edge
1170 CaseAperture(jack_pos, jack_dia, 8);
1172 CaseAperture(noisecancelmic_pos, noisecancelmic_dia, 8);
1174 OrdinaryRearApertures();
1178 // gaps for the lid's hinge arms
1179 HingePortion(hex20 - hinge_x_arms_gap,
1180 hex21 + hinge_x_arms_gap)
1183 circle(r= hinge_r_arms_gap, $fn= 8);
1186 // screw holes in the hinge arms
1190 CatchPortion(epp4[1])
1195 translate([ly_o[0], -(phone_cnr_rad + ly_re), ly_o[1]])
1196 rotate([0, ly_theta, 0])
1198 LanyardCutout(lanyard_channel_len);
1202 translate([prop_x_pos,0,0])
1205 linextr(-prop_recess_hw, +prop_recess_hw)
1207 for (d=[ [0,0], [0,-1], [+1,-1/prop_caserecess_taper] ])
1208 circleat(prcp1 + 20*d,
1214 module LidAdhocMultiprintFrame(phase){
1215 if (led_window_style >= 3) {
1216 AdhocMultiprintFrame(phase, lpp13[1], -1);
1220 module LidAroundEdges(){
1221 AroundEdges(lpp15[1], lpp13[1] - lpp15[1], 0)
1225 module Lid(){ ////toplevel
1226 skew_centre = [0, lpp11[0], lpp11[1]];
1233 translate(skew_centre)
1234 multmatrix([[ 1, 0, 0, 0 ],
1235 [ 0, 1, -lid_fold_clearance_skew, 0 ],
1238 translate(-skew_centre)
1240 LidEdgeFoldClearanceProfile();
1247 translate([0,0,-10])
1248 linear_extrude(height= 20)
1249 ButtonPlan($button_l, 1,0);
1252 translate([0,0,-100])
1253 linear_extrude(height= 200)
1254 ButtonCoverProfile();
1256 for (y= [-1,+1] * (($button_l + button_l_fudge)/2
1257 - lid_buttoncover_reinf))
1265 HingePortion(hex20, hex21) {
1270 Struts(lpp10[0] + strut_min_at_end, lpp13[1], -case_th_lid);
1272 // screw holes in the hinge arms
1276 translate([prop_x_pos, -prlp10[0], prlp10[1]])
1279 linextr(-prop_recess_hw, +prop_recess_hw)
1281 for (pa = prop_angles)
1282 PropProfile(pa, 1,1);
1284 // notification led aperture
1285 if (led_window_style)
1286 translate([led_pos[0], -led_pos[1], lpp13[1]]) {
1287 translate([0,0,-10])
1288 cylinder(r=nla_r0, h=20);
1289 if (led_window_style >= 2)
1290 translate([0,0, -nla_t])
1291 cylinder(r=nla_r2, height=20);
1296 LidAdhocMultiprintFrame(1);
1299 module HingeLever(){ ////toplevel
1301 // outer body, positive
1302 HingePortion(hex22, hex22 + phone_width/2)
1303 HingeLeverOuterProfile();
1305 // space for the screws
1306 HingePortion(hex26, hex24)
1307 HingeLeverInnerProfile();
1309 // recesses for the nuts
1310 HingePortion(hex23, hex26+1)
1311 HingeLeverNutProfile();
1313 // bores for the screws
1316 // space for the charging cable
1318 Flip_hinge() MicroUSB();
1322 module LidWindow(){ ////toplevel
1323 translate([led_pos[0], -led_pos[1], lpp13[1]])
1325 cylinder(r= nla_r1, h=nla_t);
1326 LidAdhocMultiprintFrame(0);
1329 module LidWindowPrint(){ ////toplevel
1334 module DemoLidWindowSelect(){
1335 translate([led_pos[0], led_pos[1], -100]) {
1336 translate([0, -30, 0]) cube([400, 400, 200]);
1340 module DemoLidWindow(){ ////toplevel
1343 translate([0,40,0]){
1344 color("blue") intersection(){ Lid(); DemoLidWindowSelect(); }
1345 color("red") intersection(){ LidWindow(); DemoLidWindowSelect(); }
1349 module HingeLeverPrint(){ ////toplevel
1351 translate([-phone_width/2, phone_height, 0])
1355 module TestSelectLength(){
1356 translate([-30, -200, -20])
1357 cube([30 + 15, 250, 40]);
1360 module TestLength(){ ////toplevel
1367 module TestLengthRight(){ ////toplevel
1375 module TestSelectWidth(){
1376 translate([-30, -(phone_height - 25), -20])
1378 cube([200, 50, 40]);
1381 module TestWidth(){ ////toplevel
1388 module TestLidWidthPrint(){ ////toplevel
1389 rotate([0,180.0]) intersection(){
1395 module TestSelectRearAperture(){
1398 translate([20, 0,0])
1399 cube([42, 2, 1], center=true);
1403 module TestSelectCamera(){
1405 TestSelectRearAperture()
1406 RearCameraAperture();
1407 cube([0.1, 50, 0.1]);
1411 module TestSelectOrdinaryRearApertures(){
1412 TestSelectRearAperture()
1413 OrdinaryRearApertures();
1416 module TestCamera(){ ////toplevel
1423 module TestLidByCamera(){ ////toplevel
1430 module TestLidByCameraPrint(){ ////toplevel
1431 rotate([180,0,0]) TestLidByCamera();
1434 module DemoByCamera(){ ////toplevel
1435 color("blue") TestLidByCamera();
1436 color("red") TestCamera();
1439 module OneKeeper(){ ////toplevel
1440 translate([0, -phone_cnr_rad, 0])
1442 linear_extrude(height = phone_height - phone_cnr_rad * 2)
1446 module OneKeeperPrint(){ ////toplevel
1451 module LidPrint(){ ////toplevel
1456 module TestSelectFrame(){
1457 include = [1,-1] * (epp2i[0] + 4);
1460 cube(1000, center=true);
1461 translate([0,0, -100])
1462 linear_extrude(height=200)
1463 rectfromto(include, inside_br - include);
1467 module TestSelectLidFrame(){
1469 translate([led_pos[0], -led_pos[1], -50])
1470 cylinder(r= nla_r2+3, h=100);
1473 module TestFrameCase(){ ////toplevel
1479 TestSelectOrdinaryRearApertures();
1484 module TestSelectTopApertures(){
1485 translate([-100, -35, -100])
1486 cube([400, 100, 200]);
1487 LidAdhocMultiprintFrame(0);
1488 LidAdhocMultiprintFrame(1);
1491 module TestTopApertures(){ ////toplevel
1495 TestSelectTopApertures();
1499 module TestLidTopAperturesPrint(){ ////toplevel
1500 rotate([0,180,0]) intersection(){
1502 TestSelectLidFrame();
1503 TestSelectTopApertures();
1507 module TestLidWindowTopAperturesPrint(){ ////toplevel
1508 rotate([0,180,0]) intersection(){
1510 TestSelectTopApertures();
1514 module TestFrameLidPrint(){ ////toplevel
1515 rotate([0,180,0]) intersection(){
1517 TestSelectLidFrame();
1521 module ButtonPlanForDemo(z, deep, cut){
1523 ButtonPlan(8, deep, cut);
1526 module HingeScrews(){
1527 Flip_rhs() Flip_bot(1){
1528 for (c= [ hppT, hppB ])
1533 translate([0,0,-.2])
1534 cylinder( r= hingescrew_shaft_dia/2,
1535 h = hingescrew_shaft_len+0.2 );
1537 translate([0,0,+.1])
1538 cylinder( r= hingescrew_head_dia/2, h = hingescrew_head_th );
1543 module DemoPropAngleSelect(c){
1544 color(c) difference(){
1545 union(){ children(); }
1546 translate([ prop_x_pos, -400, -200 ])
1547 cube([ 400,800,400 ]);
1551 module DemoPropAngle(ang){
1552 hL = [0, -(phone_height - hppT[0]), hppT[1] - hp_k*2];
1553 hC = [0, -(phone_height - hppB[0]), hppB[1]];
1561 DemoPropAngleSelect("red") Case();
1564 translate([prop_x_pos, -prcp1[0], prcp1[1]])
1565 PropProfileAssignments(ang) {
1567 rotate([-$prp_theta, 0, 0])
1568 translate([0, $prpp1[0], -$prpp1[1]])
1574 translate([0,0, -hp_k*2])
1575 DemoPropAngleSelect("blue")
1579 module DemoPropAngles(){ ////toplevel
1580 for (i=[0 : len(prop_angles)-1])
1581 translate(i * [0, -100, 100])
1582 DemoPropAngle(prop_angles[i]);
1585 module DemoHingeAngle(ang1,ang2){
1586 hL = [0, -(phone_height - hppT[0]), hppT[1]];
1587 hC = [0, -(phone_height - hppB[0]), hppB[1]];
1598 color("blue") intersection(){
1601 translate([bppJ[0], -400, -200])
1603 cube([400, 800, 400]);
1604 translate([10, -400, -200])
1605 cube([10, 800, 400]);
1610 module DemoHingeAngles(){ ////toplevel
1611 angles = [ 0, 4, 8, 12 ];
1612 echo("angles",angles);
1613 for (i=[0 : len(angles)-1]) {
1614 translate(i * [0, 0, 30]) {
1615 DemoHingeAngle(0,angles[i]);
1616 translate([0, 200, 0])
1617 DemoHingeAngle(angles[i],0);
1622 module DemoSelectAdhocLeftRight(right=0) {
1623 translate([phone_width/2, -400, -100]) // , -15, -100 to cross-section
1624 mirror([1-right, 0,0])
1625 cube([400, 800, 200]);
1628 module DemoLeft(){ ////toplevel
1629 color("red") intersection(){ Case(); DemoSelectAdhocLeftRight(); }
1630 color("blue") intersection(){ Lid(); DemoSelectAdhocLeftRight(); }
1633 module DemoFrame(){ ////toplevel
1634 color("red") TestFrameCase();
1635 color("blue") intersection(){ Lid(); TestSelectLidFrame(); }
1636 color("black") HingeScrews();
1640 module DemoLanyardCutout(){ ////toplevel
1644 module DemoHingedFrame(){ ///toplevel
1645 color("red") TestFrameCase();
1646 translate([0,0, -2*hp_k])
1647 color("blue") intersection(){ Lid(); TestSelectLidFrame(); }
1650 color("orange") HingeLever();
1651 color("black") HingeScrews();
1655 module DemoHinge(){ ////toplevel
1656 translate([ -0.5*phone_width, phone_height, hp_k*3 ]) {
1658 translate([0,0, -hp_k*3])
1663 module DemoProfiles(){ ////toplevel
1667 translate([0,0,-1]) color("black") KeeperProfile(1);
1670 translate([0,0,+1]) color("purple") LanyardMainChannelProfile();
1671 translate([0,0,+2]) color("red") LanyardCurveChannelProfile();
1672 translate([0, ly_q_z]){
1673 translate([0,0,-1]) color("blue") LanyardEntryChannelProfile();
1674 translate([ly_oec_y,0,-2]) color("black") LanyardEntryOuterProfile();
1678 translate([0,0,-5]) color("white") translate(epp2i)
1680 rectfromto([-15, 0],
1681 [+15, -max_case_bottom_edge_thickness]);
1684 LanyardMainChannelProfile();
1685 translate([0,0,1]) color("purple") LanyardCurveChannelProfile();
1686 translate([0,0,-1]) color("red") LanyardEntryChannelProfile();
1693 demopoint_QR = [ bppS[0], bppQ[1] - 0.1];
1695 color("blue") ButtonCoverProfile();
1697 rectfromto(bppQ, demopoint_QR);
1698 rectfromto(bppR, demopoint_QR);
1702 translate([-20,0]) {
1703 color("black") ButtonPlanForDemo(-2, 0,1);
1704 color("red" ) ButtonPlanForDemo(-4, 1,1);
1705 color("blue") ButtonPlanForDemo(-6, 1,0);
1708 translate([0, -30]) {
1711 color("blue") HingeLidProfile();
1712 color("red") HingeBaseProfile();
1713 color("black") translate([0,0,-2]) HingeLeverOuterProfile();
1717 translate([-30, -60 + 30*f]) {
1718 translate([0,0,-4]) EdgeProfile();
1719 %translate([0,0,-10]) HingeBaseProfile();
1720 translate([0,-2] * f * hp_k) {
1721 translate([0,0,-4]) LidEdgeProfile();
1722 %translate([0,0,-10]) %HingeLidProfile();
1724 translate(+hppB) rotate([0,0,180*f]) translate(-hppB) {
1725 translate([0,0,-2]) color("black") HingeLeverOuterProfile();
1726 translate([0,0,0]) color("red") difference(){
1727 HingeLeverOuterProfile();
1728 HingeLeverInnerProfile();
1730 translate([0,0,3]) color("yellow") HingeLeverNutProfile();
1735 translate([20,-30]) {
1738 //translate([0,0,1]) CatchCutProfile();
1739 translate([0,0,+1]) color("red")
1740 difference(){ EdgeProfile(); CatchCutProfile(); }
1743 translate([40,-30]) {
1747 PropProfile(10, 1, 0);
1752 translate([60,-30]) {
1753 PropAggregateProfile();