These are still untested, and most of them are unordered and missing proper [info] section
--- /dev/null
+[info]
+name = Default
+
+[profile]
+layer_height = 0.25
+wall_thickness = 1
+retraction_enable = True
+solid_layer_thickness = 1
+fill_density = 20
+nozzle_size = 0.5
+print_speed = 50
+print_temperature = 235
+print_temperature2 = 0
+print_temperature3 = 0
+print_temperature4 = 0
+print_bed_temperature = 100
+support = None
+platform_adhesion = None
+support_dual_extrusion = Both
+wipe_tower = False
+wipe_tower_volume = 15
+ooze_shield = False
+filament_diameter = 2.85
+filament_diameter2 = 0
+filament_diameter3 = 0
+filament_diameter4 = 0
+filament_flow = 100.0
+retraction_speed = 10
+retraction_amount = 1.5
+retraction_dual_amount = 16.5
+retraction_min_travel = 1.5
+retraction_combing = True
+retraction_minimal_extrusion = 0.005
+retraction_hop = 0.1
+bottom_thickness = 0.425
+layer0_width_factor = 125
+object_sink = 0
+overlap_dual = 0.15
+travel_speed = 175
+bottom_layer_speed = 10
+infill_speed = 30
+inset0_speed = 20
+insetx_speed = 25
+cool_min_layer_time = 5
+fan_enabled = True
+skirt_line_count = 1
+skirt_gap = 3.0
+skirt_minimal_length = 250
+fan_full_height = 3
+fan_speed = 30
+fan_speed_max = 40
+cool_min_feedrate = 10
+cool_head_lift = False
+solid_top = True
+solid_bottom = True
+fill_overlap = 15
+support_type = Lines
+support_angle = 45
+support_fill_rate = 30
+support_xy_distance = 0.7
+support_z_distance = 0.05
+spiralize = False
+simple_mode = False
+brim_line_count = 10
+raft_margin = 5.0
+raft_line_spacing = 3.0
+raft_base_thickness = 0.3
+raft_base_linewidth = 1.0
+raft_interface_thickness = 0.27
+raft_interface_linewidth = 0.4
+raft_airgap = 0.5
+raft_surface_layers = 2
+fix_horrible_union_all_type_a = True
+fix_horrible_union_all_type_b = False
+fix_horrible_use_open_bits = False
+fix_horrible_extensive_stitching = False
+plugin_config =
+object_center_x = -1
+object_center_y = -1
+
+[alterations]
+start.gcode = ;This Gcode has been generated specifically for the LulzBot Mini
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Filament Diameter: {filament_diameter}
+ ;Nozzle Size: {nozzle_size}
+ G21 ; metric values
+ G90 ; absolute positioning
+ M82 ; set extruder to absolute mode
+ M107 ; start with the fan off
+ G92 E0 ; set extruder position to 0
+ M140 S{print_bed_temperature}; get bed heating up
+ G28 ; home all
+ M109 S160 ; set to cleaning temp and wait
+ G1 Z150 E-30 F75 ; suck up XXmm of filament
+ M109 S170 ; heat up rest of way
+ G1 X45 Y174 F11520 ; move behind scraper
+ G1 Z0 F1200 ; CRITICAL: set Z to height of top of scraper
+ G1 X45 Y174 Z-.5 F4000 ; wiping ; plunge into wipe pad
+ G1 X55 Y172 Z-.5 F4000 ; wiping
+ G1 X45 Y174 Z0 F4000 ; wiping
+ G1 X55 Y172 F4000 ; wiping
+ G1 X45 Y174 F4000 ; wiping
+ G1 X55 Y172 F4000 ; wiping
+ G1 X45 Y174 F4000 ; wiping
+ G1 X55 Y172 F4000 ; wiping
+ G1 X60 Y174 F4000 ; wiping
+ G1 X80 Y172 F4000 ; wiping
+ G1 X60 Y174 F4000 ; wiping
+ G1 X80 Y172 F4000 ; wiping
+ G1 X60 Y174 F4000 ; wiping
+ G1 X90 Y172 F4000 ; wiping
+ G1 X80 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X80 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X80 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X110 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X110 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X110 Y174 F4000 ; wiping
+ G1 X115 Y172 Z-0.5 F1000 ; wipe slower and bury noz in cleanish area
+ G1 Z10 ; raise z
+ G28 X0 Y0 ; home x and y
+ M109 S170 ; set to probing temp
+ M204 S300 ; Set probing acceleration
+ G29 ; Probe
+ M204 S2000 ; Restore standard acceleration
+ G1 X5 Y15 Z10 F5000 ; get out the way
+ G4 S1 ; pause
+ M400 ; clear buffer
+ M109 S{print_temperature} ; set extruder temp and wait
+ G4 S15 ; wait for bed to temp up
+ G1 Z2 E0 F75 ; extrude filament back into nozzle
+ M140 S{print_bed_temperature}; get bed temping up during first layer
+end.gcode =
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M104 S0 ;
+ G1 X145 Y175 Z156 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
+start2.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M104 S{print_temperature} ;Uncomment to add your own temperature line
+ ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ T1 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T0 ;Switch to the first extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Printing...
+end2.gcode = ;End GCode
+ M104 T0 S0 ;extruder heater off
+ M104 T1 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ M84 ;steppers off
+ G90 ;absolute positioning
+ ;{profile_string}
+start3.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M104 S{print_temperature} ;Uncomment to add your own temperature line
+ ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ T2 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T1 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T0 ;Switch to the first extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Printing...
+end3.gcode = ;End GCode
+ M104 T0 S0 ;extruder heater off
+ M104 T1 S0 ;extruder heater off
+ M104 T2 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ M84 ;steppers off
+ G90 ;absolute positioning
+ ;{profile_string}
+start4.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M104 S{print_temperature} ;Uncomment to add your own temperature line
+ ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ T3 ;Switch to the 4th extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T2 ;Switch to the 3th extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T1 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T0 ;Switch to the first extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Printing...
+end4.gcode = ;End GCode
+ M104 T0 S0 ;extruder heater off
+ M104 T1 S0 ;extruder heater off
+ M104 T2 S0 ;extruder heater off
+ M104 T3 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ M84 ;steppers off
+ G90 ;absolute positioning
+ ;{profile_string}
+support_start.gcode =
+support_end.gcode =
+cool_start.gcode =
+cool_end.gcode =
+replace.csv =
+preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
+ ;This code is added before the T(n)
+postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
+ ;This code is added after the T(n)
+
--- /dev/null
+[info]
+name = Taulman Alloy 910
--- /dev/null
+[info]
+always_visible = 0
+
+[profile]
+layer_height = 0.38
+wall_thickness = 1
+retraction_enable = True
+solid_layer_thickness = 1
+fill_density = 20
+nozzle_size = 0.5
+print_speed = 50
+print_temperature = 190
+print_temperature2 = 0
+print_temperature3 = 0
+print_temperature4 = 0
+print_bed_temperature = 60
+support = None
+platform_adhesion = None
+support_dual_extrusion = Both
+wipe_tower = False
+wipe_tower_volume = 15
+ooze_shield = False
+filament_diameter = 2.85
+filament_diameter2 = 0
+filament_diameter3 = 0
+filament_diameter4 = 0
+filament_flow = 100.0
+retraction_speed = 10
+retraction_amount = 1.5
+retraction_dual_amount = 16.5
+retraction_min_travel = 1.5
+retraction_combing = True
+retraction_minimal_extrusion = 0.005
+retraction_hop = 0.1
+bottom_thickness = 0.425
+layer0_width_factor = 125
+object_sink = 0.0
+overlap_dual = 0.15
+travel_speed = 175
+bottom_layer_speed = 15
+infill_speed = 50
+inset0_speed = 40
+insetx_speed = 45
+cool_min_layer_time = 20
+fan_enabled = True
+skirt_line_count = 1
+skirt_gap = 3.0
+skirt_minimal_length = 250
+fan_full_height = 0.5
+fan_speed = 75
+fan_speed_max = 100
+cool_min_feedrate = 10
+cool_head_lift = False
+solid_top = True
+solid_bottom = True
+fill_overlap = 15
+support_type = Lines
+support_angle = 45
+support_fill_rate = 30
+support_xy_distance = 0.7
+support_z_distance = 0.05
+spiralize = False
+simple_mode = False
+brim_line_count = 10
+raft_margin = 5.0
+raft_line_spacing = 3.0
+raft_base_thickness = 0.3
+raft_base_linewidth = 1.0
+raft_interface_thickness = 0.27
+raft_interface_linewidth = 0.4
+raft_airgap = 0.5
+raft_surface_layers = 2
+fix_horrible_union_all_type_a = True
+fix_horrible_union_all_type_b = False
+fix_horrible_use_open_bits = False
+fix_horrible_extensive_stitching = False
+plugin_config =
+object_center_x = -1
+object_center_y = -1
+
+[alterations]
+start.gcode = ;This Gcode has been generated specifically for the LulzBot Mini
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Filament Diameter: {filament_diameter}
+ ;Nozzle Size: {nozzle_size}
+ G21 ; metric values
+ G90 ; absolute positioning
+ M82 ; set extruder to absolute mode
+ M107 ; start with the fan off
+ G92 E0 ; set extruder position to 0
+ M140 S{print_bed_temperature}; get bed heating up
+ G28 ; home all
+ M109 S140 ; set to cleaning temp and wait
+ G1 Z150 E-30 F75 ; suck up XXmm of filament
+ M109 S140 ; heat up rest of way
+ G1 X45 Y174 F11520 ; move behind scraper
+ G1 Z0 F1200 ; CRITICAL: set Z to height of top of scraper
+ G1 X45 Y174 Z-.5 F4000 ; wiping ; plunge into wipe pad
+ G1 X55 Y172 Z-.5 F4000 ; wiping
+ G1 X45 Y174 Z0 F4000 ; wiping
+ G1 X55 Y172 F4000 ; wiping
+ G1 X45 Y174 F4000 ; wiping
+ G1 X55 Y172 F4000 ; wiping
+ G1 X45 Y174 F4000 ; wiping
+ G1 X55 Y172 F4000 ; wiping
+ G1 X60 Y174 F4000 ; wiping
+ G1 X80 Y172 F4000 ; wiping
+ G1 X60 Y174 F4000 ; wiping
+ G1 X80 Y172 F4000 ; wiping
+ G1 X60 Y174 F4000 ; wiping
+ G1 X90 Y172 F4000 ; wiping
+ G1 X80 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X80 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X80 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X110 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X110 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X110 Y174 F4000 ; wiping
+ G1 X115 Y172 Z-0.5 F1000 ; wipe slower and bury noz in cleanish area
+ G1 Z10 ; raise z
+ G28 X0 Y0 ; home x and y
+ M109 S140 ; set to probing temp
+ M204 S300 ; Set probing acceleration
+ G29 ; Probe
+ M204 S2000 ; Restore standard acceleration
+ G1 X5 Y15 Z10 F5000 ; get out the way
+ G4 S1 ; pause
+ M400 ; clear buffer
+ M109 S{print_temperature} ; set extruder temp and wait
+ G4 S15 ; wait for bed to temp up
+ G1 Z2 E0 F75 ; extrude filament back into nozzle
+ M140 S{print_bed_temperature}; get bed temping up during first layer
+end.gcode =
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M104 S0 ;
+ G1 X145 Y175 Z156 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
+start2.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M104 S{print_temperature} ;Uncomment to add your own temperature line
+ ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ T1 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T0 ;Switch to the first extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Printing...
+end2.gcode = ;End GCode
+ M104 T0 S0 ;extruder heater off
+ M104 T1 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ M84 ;steppers off
+ G90 ;absolute positioning
+ ;{profile_string}
+start3.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M104 S{print_temperature} ;Uncomment to add your own temperature line
+ ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ T2 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T1 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T0 ;Switch to the first extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Printing...
+end3.gcode = ;End GCode
+ M104 T0 S0 ;extruder heater off
+ M104 T1 S0 ;extruder heater off
+ M104 T2 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ M84 ;steppers off
+ G90 ;absolute positioning
+ ;{profile_string}
+start4.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M104 S{print_temperature} ;Uncomment to add your own temperature line
+ ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ T3 ;Switch to the 4th extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T2 ;Switch to the 3th extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T1 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T0 ;Switch to the first extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Printing...
+end4.gcode = ;End GCode
+ M104 T0 S0 ;extruder heater off
+ M104 T1 S0 ;extruder heater off
+ M104 T2 S0 ;extruder heater off
+ M104 T3 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ M84 ;steppers off
+ G90 ;absolute positioning
+ ;{profile_string}
+support_start.gcode =
+support_end.gcode =
+cool_start.gcode =
+cool_end.gcode =
+replace.csv =
+preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
+ ;This code is added before the T(n)
+postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
+ ;This code is added after the T(n)
+
--- /dev/null
+[info]
+name = ColorFab BambooFill
--- /dev/null
+[info]
+always_visible = 0
+
+[profile]
+layer_height = 0.38
+wall_thickness = 1
+retraction_enable = True
+solid_layer_thickness = 1
+fill_density = 20
+nozzle_size = 0.5
+print_speed = 50
+print_temperature = 230
+print_temperature2 = 0
+print_temperature3 = 0
+print_temperature4 = 0
+print_bed_temperature = 60
+support = None
+platform_adhesion = None
+support_dual_extrusion = Both
+wipe_tower = False
+wipe_tower_volume = 15
+ooze_shield = False
+filament_diameter = 2.85
+filament_diameter2 = 0
+filament_diameter3 = 0
+filament_diameter4 = 0
+filament_flow = 100.0
+retraction_speed = 10
+retraction_amount = 1.5
+retraction_dual_amount = 16.5
+retraction_min_travel = 1.5
+retraction_combing = True
+retraction_minimal_extrusion = 0.005
+retraction_hop = 0.1
+bottom_thickness = 0.425
+layer0_width_factor = 125
+object_sink = 0.0
+overlap_dual = 0.15
+travel_speed = 175
+bottom_layer_speed = 15
+infill_speed = 40
+inset0_speed = 30
+insetx_speed = 35
+cool_min_layer_time = 20
+fan_enabled = True
+skirt_line_count = 1
+skirt_gap = 3.0
+skirt_minimal_length = 250
+fan_full_height = 0.5
+fan_speed = 75
+fan_speed_max = 100
+cool_min_feedrate = 10
+cool_head_lift = False
+solid_top = True
+solid_bottom = True
+fill_overlap = 15
+support_type = Lines
+support_angle = 45
+support_fill_rate = 30
+support_xy_distance = 0.7
+support_z_distance = 0.05
+spiralize = False
+simple_mode = False
+brim_line_count = 10
+raft_margin = 5.0
+raft_line_spacing = 3.0
+raft_base_thickness = 0.3
+raft_base_linewidth = 1.0
+raft_interface_thickness = 0.27
+raft_interface_linewidth = 0.4
+raft_airgap = 0.5
+raft_surface_layers = 2
+fix_horrible_union_all_type_a = True
+fix_horrible_union_all_type_b = False
+fix_horrible_use_open_bits = False
+fix_horrible_extensive_stitching = False
+plugin_config =
+object_center_x = -1
+object_center_y = -1
+
+[alterations]
+start.gcode = ;This Gcode has been generated specifically for the LulzBot Mini
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Filament Diameter: {filament_diameter}
+ ;Nozzle Size: {nozzle_size}
+ G21 ; metric values
+ G90 ; absolute positioning
+ M82 ; set extruder to absolute mode
+ M107 ; start with the fan off
+ G92 E0 ; set extruder position to 0
+ M140 S{print_bed_temperature}; get bed heating up
+ G28 ; home all
+ M109 S140 ; set to cleaning temp and wait
+ G1 Z150 E-30 F75 ; suck up XXmm of filament
+ M109 S140 ; heat up rest of way
+ G1 X45 Y174 F11520 ; move behind scraper
+ G1 Z0 F1200 ; CRITICAL: set Z to height of top of scraper
+ G1 X45 Y174 Z-.5 F4000 ; wiping ; plunge into wipe pad
+ G1 X55 Y172 Z-.5 F4000 ; wiping
+ G1 X45 Y174 Z0 F4000 ; wiping
+ G1 X55 Y172 F4000 ; wiping
+ G1 X45 Y174 F4000 ; wiping
+ G1 X55 Y172 F4000 ; wiping
+ G1 X45 Y174 F4000 ; wiping
+ G1 X55 Y172 F4000 ; wiping
+ G1 X60 Y174 F4000 ; wiping
+ G1 X80 Y172 F4000 ; wiping
+ G1 X60 Y174 F4000 ; wiping
+ G1 X80 Y172 F4000 ; wiping
+ G1 X60 Y174 F4000 ; wiping
+ G1 X90 Y172 F4000 ; wiping
+ G1 X80 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X80 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X80 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X110 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X110 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X110 Y174 F4000 ; wiping
+ G1 X115 Y172 Z-0.5 F1000 ; wipe slower and bury noz in cleanish area
+ G1 Z10 ; raise z
+ G28 X0 Y0 ; home x and y
+ M109 S140 ; set to probing temp
+ M204 S300 ; Set probing acceleration
+ G29 ; Probe
+ M204 S2000 ; Restore standard acceleration
+ G1 X5 Y15 Z10 F5000 ; get out the way
+ G4 S1 ; pause
+ M400 ; clear buffer
+ M109 S{print_temperature} ; set extruder temp and wait
+ G4 S15 ; wait for bed to temp up
+ G1 Z2 E0 F75 ; extrude filament back into nozzle
+ M140 S{print_bed_temperature}; get bed temping up during first layer
+end.gcode =
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M104 S0 ;
+ G1 X145 Y175 Z156 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
+start2.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M104 S{print_temperature} ;Uncomment to add your own temperature line
+ ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ T1 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T0 ;Switch to the first extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Printing...
+end2.gcode = ;End GCode
+ M104 T0 S0 ;extruder heater off
+ M104 T1 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ M84 ;steppers off
+ G90 ;absolute positioning
+ ;{profile_string}
+start3.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M104 S{print_temperature} ;Uncomment to add your own temperature line
+ ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ T2 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T1 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T0 ;Switch to the first extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Printing...
+end3.gcode = ;End GCode
+ M104 T0 S0 ;extruder heater off
+ M104 T1 S0 ;extruder heater off
+ M104 T2 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ M84 ;steppers off
+ G90 ;absolute positioning
+ ;{profile_string}
+start4.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M104 S{print_temperature} ;Uncomment to add your own temperature line
+ ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ T3 ;Switch to the 4th extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T2 ;Switch to the 3th extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T1 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T0 ;Switch to the first extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Printing...
+end4.gcode = ;End GCode
+ M104 T0 S0 ;extruder heater off
+ M104 T1 S0 ;extruder heater off
+ M104 T2 S0 ;extruder heater off
+ M104 T3 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ M84 ;steppers off
+ G90 ;absolute positioning
+ ;{profile_string}
+support_start.gcode =
+support_end.gcode =
+cool_start.gcode =
+cool_end.gcode =
+replace.csv =
+preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
+ ;This code is added before the T(n)
+postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
+ ;This code is added after the T(n)
+
--- /dev/null
+[info]
+name = ColorFab BronzeFill
--- /dev/null
+[info]
+always_visible = 0
+
+[profile]
+layer_height = 0.38
+wall_thickness = 1
+retraction_enable = True
+solid_layer_thickness = 1
+fill_density = 20
+nozzle_size = 0.5
+print_speed = 50
+print_temperature = 230
+print_temperature2 = 0
+print_temperature3 = 0
+print_temperature4 = 0
+print_bed_temperature = 60
+support = None
+platform_adhesion = None
+support_dual_extrusion = Both
+wipe_tower = False
+wipe_tower_volume = 15
+ooze_shield = False
+filament_diameter = 2.85
+filament_diameter2 = 0
+filament_diameter3 = 0
+filament_diameter4 = 0
+filament_flow = 100.0
+retraction_speed = 10
+retraction_amount = 1.5
+retraction_dual_amount = 16.5
+retraction_min_travel = 1.5
+retraction_combing = True
+retraction_minimal_extrusion = 0.005
+retraction_hop = 0.1
+bottom_thickness = 0.425
+layer0_width_factor = 125
+object_sink = 0.0
+overlap_dual = 0.15
+travel_speed = 175
+bottom_layer_speed = 15
+infill_speed = 40
+inset0_speed = 30
+insetx_speed = 35
+cool_min_layer_time = 20
+fan_enabled = True
+skirt_line_count = 1
+skirt_gap = 3.0
+skirt_minimal_length = 250
+fan_full_height = 0.5
+fan_speed = 75
+fan_speed_max = 100
+cool_min_feedrate = 10
+cool_head_lift = False
+solid_top = True
+solid_bottom = True
+fill_overlap = 15
+support_type = Lines
+support_angle = 45
+support_fill_rate = 30
+support_xy_distance = 0.7
+support_z_distance = 0.05
+spiralize = False
+simple_mode = False
+brim_line_count = 10
+raft_margin = 5.0
+raft_line_spacing = 3.0
+raft_base_thickness = 0.3
+raft_base_linewidth = 1.0
+raft_interface_thickness = 0.27
+raft_interface_linewidth = 0.4
+raft_airgap = 0.5
+raft_surface_layers = 2
+fix_horrible_union_all_type_a = True
+fix_horrible_union_all_type_b = False
+fix_horrible_use_open_bits = False
+fix_horrible_extensive_stitching = False
+plugin_config =
+object_center_x = -1
+object_center_y = -1
+
+[alterations]
+start.gcode = ;This Gcode has been generated specifically for the LulzBot Mini
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Filament Diameter: {filament_diameter}
+ ;Nozzle Size: {nozzle_size}
+ G21 ; metric values
+ G90 ; absolute positioning
+ M82 ; set extruder to absolute mode
+ M107 ; start with the fan off
+ G92 E0 ; set extruder position to 0
+ M140 S{print_bed_temperature}; get bed heating up
+ G28 ; home all
+ M109 S140 ; set to cleaning temp and wait
+ G1 Z150 E-30 F75 ; suck up XXmm of filament
+ M109 S140 ; heat up rest of way
+ G1 X45 Y174 F11520 ; move behind scraper
+ G1 Z0 F1200 ; CRITICAL: set Z to height of top of scraper
+ G1 X45 Y174 Z-.5 F4000 ; wiping ; plunge into wipe pad
+ G1 X55 Y172 Z-.5 F4000 ; wiping
+ G1 X45 Y174 Z0 F4000 ; wiping
+ G1 X55 Y172 F4000 ; wiping
+ G1 X45 Y174 F4000 ; wiping
+ G1 X55 Y172 F4000 ; wiping
+ G1 X45 Y174 F4000 ; wiping
+ G1 X55 Y172 F4000 ; wiping
+ G1 X60 Y174 F4000 ; wiping
+ G1 X80 Y172 F4000 ; wiping
+ G1 X60 Y174 F4000 ; wiping
+ G1 X80 Y172 F4000 ; wiping
+ G1 X60 Y174 F4000 ; wiping
+ G1 X90 Y172 F4000 ; wiping
+ G1 X80 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X80 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X80 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X110 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X110 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X110 Y174 F4000 ; wiping
+ G1 X115 Y172 Z-0.5 F1000 ; wipe slower and bury noz in cleanish area
+ G1 Z10 ; raise z
+ G28 X0 Y0 ; home x and y
+ M109 S140 ; set to probing temp
+ M204 S300 ; Set probing acceleration
+ G29 ; Probe
+ M204 S2000 ; Restore standard acceleration
+ G1 X5 Y15 Z10 F5000 ; get out the way
+ G4 S1 ; pause
+ M400 ; clear buffer
+ M109 S{print_temperature} ; set extruder temp and wait
+ G4 S15 ; wait for bed to temp up
+ G1 Z2 E0 F75 ; extrude filament back into nozzle
+ M140 S{print_bed_temperature}; get bed temping up during first layer
+end.gcode =
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M104 S0 ;
+ G1 X145 Y175 Z156 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
+start2.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M104 S{print_temperature} ;Uncomment to add your own temperature line
+ ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ T1 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T0 ;Switch to the first extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Printing...
+end2.gcode = ;End GCode
+ M104 T0 S0 ;extruder heater off
+ M104 T1 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ M84 ;steppers off
+ G90 ;absolute positioning
+ ;{profile_string}
+start3.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M104 S{print_temperature} ;Uncomment to add your own temperature line
+ ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ T2 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T1 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T0 ;Switch to the first extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Printing...
+end3.gcode = ;End GCode
+ M104 T0 S0 ;extruder heater off
+ M104 T1 S0 ;extruder heater off
+ M104 T2 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ M84 ;steppers off
+ G90 ;absolute positioning
+ ;{profile_string}
+start4.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M104 S{print_temperature} ;Uncomment to add your own temperature line
+ ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ T3 ;Switch to the 4th extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T2 ;Switch to the 3th extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T1 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T0 ;Switch to the first extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Printing...
+end4.gcode = ;End GCode
+ M104 T0 S0 ;extruder heater off
+ M104 T1 S0 ;extruder heater off
+ M104 T2 S0 ;extruder heater off
+ M104 T3 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ M84 ;steppers off
+ G90 ;absolute positioning
+ ;{profile_string}
+support_start.gcode =
+support_end.gcode =
+cool_start.gcode =
+cool_end.gcode =
+replace.csv =
+preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
+ ;This code is added before the T(n)
+postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
+ ;This code is added after the T(n)
+
--- /dev/null
+[info]
+name = ColorFab CopperFill
[info]
name = HIPS
order = 0
+default = 1
--- /dev/null
+[info]
+always_visible = 0
+
+[profile]
+layer_height = 0.2
+wall_thickness = 1
+retraction_enable = True
+solid_layer_thickness = 1
+fill_density = 20
+nozzle_size = 0.5
+print_speed = 50
+print_temperature = 190
+print_temperature2 = 0
+print_temperature3 = 0
+print_temperature4 = 0
+print_bed_temperature = 60
+support = None
+platform_adhesion = None
+support_dual_extrusion = Both
+wipe_tower = False
+wipe_tower_volume = 15
+ooze_shield = False
+filament_diameter = 2.85
+filament_diameter2 = 0
+filament_diameter3 = 0
+filament_diameter4 = 0
+filament_flow = 100.0
+retraction_speed = 10
+retraction_amount = 1.5
+retraction_dual_amount = 16.5
+retraction_min_travel = 1.5
+retraction_combing = True
+retraction_minimal_extrusion = 0.005
+retraction_hop = 0.1
+bottom_thickness = 0.425
+layer0_width_factor = 125
+object_sink = 0.0
+overlap_dual = 0.15
+travel_speed = 175
+bottom_layer_speed = 10
+infill_speed = 30
+inset0_speed = 25
+insetx_speed = 27.5
+cool_min_layer_time = 20
+fan_enabled = True
+skirt_line_count = 1
+skirt_gap = 3.0
+skirt_minimal_length = 250
+fan_full_height = 0.5
+fan_speed = 75
+fan_speed_max = 100
+cool_min_feedrate = 10
+cool_head_lift = False
+solid_top = True
+solid_bottom = True
+fill_overlap = 15
+support_type = Lines
+support_angle = 45
+support_fill_rate = 30
+support_xy_distance = 0.7
+support_z_distance = 0.05
+spiralize = False
+simple_mode = False
+brim_line_count = 10
+raft_margin = 5.0
+raft_line_spacing = 3.0
+raft_base_thickness = 0.3
+raft_base_linewidth = 1.0
+raft_interface_thickness = 0.27
+raft_interface_linewidth = 0.4
+raft_airgap = 0.5
+raft_surface_layers = 2
+fix_horrible_union_all_type_a = True
+fix_horrible_union_all_type_b = False
+fix_horrible_use_open_bits = False
+fix_horrible_extensive_stitching = False
+plugin_config =
+object_center_x = -1
+object_center_y = -1
+
+[alterations]
+start.gcode = ;This Gcode has been generated specifically for the LulzBot Mini
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Filament Diameter: {filament_diameter}
+ ;Nozzle Size: {nozzle_size}
+ G21 ; metric values
+ G90 ; absolute positioning
+ M82 ; set extruder to absolute mode
+ M107 ; start with the fan off
+ G92 E0 ; set extruder position to 0
+ M140 S{print_bed_temperature}; get bed heating up
+ G28 ; home all
+ M109 S140 ; set to cleaning temp and wait
+ G1 Z150 E-30 F75 ; suck up XXmm of filament
+ M109 S140 ; heat up rest of way
+ G1 X45 Y174 F11520 ; move behind scraper
+ G1 Z0 F1200 ; CRITICAL: set Z to height of top of scraper
+ G1 X45 Y174 Z-.5 F4000 ; wiping ; plunge into wipe pad
+ G1 X55 Y172 Z-.5 F4000 ; wiping
+ G1 X45 Y174 Z0 F4000 ; wiping
+ G1 X55 Y172 F4000 ; wiping
+ G1 X45 Y174 F4000 ; wiping
+ G1 X55 Y172 F4000 ; wiping
+ G1 X45 Y174 F4000 ; wiping
+ G1 X55 Y172 F4000 ; wiping
+ G1 X60 Y174 F4000 ; wiping
+ G1 X80 Y172 F4000 ; wiping
+ G1 X60 Y174 F4000 ; wiping
+ G1 X80 Y172 F4000 ; wiping
+ G1 X60 Y174 F4000 ; wiping
+ G1 X90 Y172 F4000 ; wiping
+ G1 X80 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X80 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X80 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X110 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X110 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X110 Y174 F4000 ; wiping
+ G1 X115 Y172 Z-0.5 F1000 ; wipe slower and bury noz in cleanish area
+ G1 Z10 ; raise z
+ G28 X0 Y0 ; home x and y
+ M109 S140 ; set to probing temp
+ M204 S300 ; Set probing acceleration
+ G29 ; Probe
+ M204 S2000 ; Restore standard acceleration
+ G1 X5 Y15 Z10 F5000 ; get out the way
+ G4 S1 ; pause
+ M400 ; clear buffer
+ M109 S{print_temperature} ; set extruder temp and wait
+ G4 S15 ; wait for bed to temp up
+ G1 Z2 E0 F75 ; extrude filament back into nozzle
+ M140 S{print_bed_temperature}; get bed temping up during first layer
+end.gcode =
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M104 S0 ;
+ G1 X145 Y175 Z156 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
+start2.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M104 S{print_temperature} ;Uncomment to add your own temperature line
+ ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ T1 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T0 ;Switch to the first extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Printing...
+end2.gcode = ;End GCode
+ M104 T0 S0 ;extruder heater off
+ M104 T1 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ M84 ;steppers off
+ G90 ;absolute positioning
+ ;{profile_string}
+start3.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M104 S{print_temperature} ;Uncomment to add your own temperature line
+ ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ T2 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T1 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T0 ;Switch to the first extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Printing...
+end3.gcode = ;End GCode
+ M104 T0 S0 ;extruder heater off
+ M104 T1 S0 ;extruder heater off
+ M104 T2 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ M84 ;steppers off
+ G90 ;absolute positioning
+ ;{profile_string}
+start4.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M104 S{print_temperature} ;Uncomment to add your own temperature line
+ ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ T3 ;Switch to the 4th extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T2 ;Switch to the 3th extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T1 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T0 ;Switch to the first extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Printing...
+end4.gcode = ;End GCode
+ M104 T0 S0 ;extruder heater off
+ M104 T1 S0 ;extruder heater off
+ M104 T2 S0 ;extruder heater off
+ M104 T3 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ M84 ;steppers off
+ G90 ;absolute positioning
+ ;{profile_string}
+support_start.gcode =
+support_end.gcode =
+cool_start.gcode =
+cool_end.gcode =
+replace.csv =
+preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
+ ;This code is added before the T(n)
+postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
+ ;This code is added after the T(n)
+
--- /dev/null
+[info]
+name = LayBrick
--- /dev/null
+[info]
+always_visible = 0
+
+[profile]
+layer_height = 0.38
+wall_thickness = 1
+retraction_enable = True
+solid_layer_thickness = 1
+fill_density = 20
+nozzle_size = 0.5
+print_speed = 50
+print_temperature = 190
+print_temperature2 = 0
+print_temperature3 = 0
+print_temperature4 = 0
+print_bed_temperature = 60
+support = None
+platform_adhesion = None
+support_dual_extrusion = Both
+wipe_tower = False
+wipe_tower_volume = 15
+ooze_shield = False
+filament_diameter = 2.85
+filament_diameter2 = 0
+filament_diameter3 = 0
+filament_diameter4 = 0
+filament_flow = 100.0
+retraction_speed = 10
+retraction_amount = 1.5
+retraction_dual_amount = 16.5
+retraction_min_travel = 1.5
+retraction_combing = True
+retraction_minimal_extrusion = 0.005
+retraction_hop = 0.1
+bottom_thickness = 0.425
+layer0_width_factor = 125
+object_sink = 0.0
+overlap_dual = 0.15
+travel_speed = 175
+bottom_layer_speed = 15
+infill_speed = 50
+inset0_speed = 40
+insetx_speed = 45
+cool_min_layer_time = 20
+fan_enabled = True
+skirt_line_count = 1
+skirt_gap = 3.0
+skirt_minimal_length = 250
+fan_full_height = 0.5
+fan_speed = 75
+fan_speed_max = 100
+cool_min_feedrate = 10
+cool_head_lift = False
+solid_top = True
+solid_bottom = True
+fill_overlap = 15
+support_type = Lines
+support_angle = 45
+support_fill_rate = 30
+support_xy_distance = 0.7
+support_z_distance = 0.05
+spiralize = False
+simple_mode = False
+brim_line_count = 10
+raft_margin = 5.0
+raft_line_spacing = 3.0
+raft_base_thickness = 0.3
+raft_base_linewidth = 1.0
+raft_interface_thickness = 0.27
+raft_interface_linewidth = 0.4
+raft_airgap = 0.5
+raft_surface_layers = 2
+fix_horrible_union_all_type_a = True
+fix_horrible_union_all_type_b = False
+fix_horrible_use_open_bits = False
+fix_horrible_extensive_stitching = False
+plugin_config =
+object_center_x = -1
+object_center_y = -1
+
+[alterations]
+start.gcode = ;This Gcode has been generated specifically for the LulzBot Mini
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Filament Diameter: {filament_diameter}
+ ;Nozzle Size: {nozzle_size}
+ G21 ; metric values
+ G90 ; absolute positioning
+ M82 ; set extruder to absolute mode
+ M107 ; start with the fan off
+ G92 E0 ; set extruder position to 0
+ M140 S{print_bed_temperature}; get bed heating up
+ G28 ; home all
+ M109 S140 ; set to cleaning temp and wait
+ G1 Z150 E-30 F75 ; suck up XXmm of filament
+ M109 S140 ; heat up rest of way
+ G1 X45 Y174 F11520 ; move behind scraper
+ G1 Z0 F1200 ; CRITICAL: set Z to height of top of scraper
+ G1 X45 Y174 Z-.5 F4000 ; wiping ; plunge into wipe pad
+ G1 X55 Y172 Z-.5 F4000 ; wiping
+ G1 X45 Y174 Z0 F4000 ; wiping
+ G1 X55 Y172 F4000 ; wiping
+ G1 X45 Y174 F4000 ; wiping
+ G1 X55 Y172 F4000 ; wiping
+ G1 X45 Y174 F4000 ; wiping
+ G1 X55 Y172 F4000 ; wiping
+ G1 X60 Y174 F4000 ; wiping
+ G1 X80 Y172 F4000 ; wiping
+ G1 X60 Y174 F4000 ; wiping
+ G1 X80 Y172 F4000 ; wiping
+ G1 X60 Y174 F4000 ; wiping
+ G1 X90 Y172 F4000 ; wiping
+ G1 X80 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X80 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X80 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X110 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X110 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X110 Y174 F4000 ; wiping
+ G1 X115 Y172 Z-0.5 F1000 ; wipe slower and bury noz in cleanish area
+ G1 Z10 ; raise z
+ G28 X0 Y0 ; home x and y
+ M109 S140 ; set to probing temp
+ M204 S300 ; Set probing acceleration
+ G29 ; Probe
+ M204 S2000 ; Restore standard acceleration
+ G1 X5 Y15 Z10 F5000 ; get out the way
+ G4 S1 ; pause
+ M400 ; clear buffer
+ M109 S{print_temperature} ; set extruder temp and wait
+ G4 S15 ; wait for bed to temp up
+ G1 Z2 E0 F75 ; extrude filament back into nozzle
+ M140 S{print_bed_temperature}; get bed temping up during first layer
+end.gcode =
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M104 S0 ;
+ G1 X145 Y175 Z156 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
+start2.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M104 S{print_temperature} ;Uncomment to add your own temperature line
+ ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ T1 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T0 ;Switch to the first extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Printing...
+end2.gcode = ;End GCode
+ M104 T0 S0 ;extruder heater off
+ M104 T1 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ M84 ;steppers off
+ G90 ;absolute positioning
+ ;{profile_string}
+start3.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M104 S{print_temperature} ;Uncomment to add your own temperature line
+ ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ T2 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T1 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T0 ;Switch to the first extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Printing...
+end3.gcode = ;End GCode
+ M104 T0 S0 ;extruder heater off
+ M104 T1 S0 ;extruder heater off
+ M104 T2 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ M84 ;steppers off
+ G90 ;absolute positioning
+ ;{profile_string}
+start4.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M104 S{print_temperature} ;Uncomment to add your own temperature line
+ ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ T3 ;Switch to the 4th extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T2 ;Switch to the 3th extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T1 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T0 ;Switch to the first extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Printing...
+end4.gcode = ;End GCode
+ M104 T0 S0 ;extruder heater off
+ M104 T1 S0 ;extruder heater off
+ M104 T2 S0 ;extruder heater off
+ M104 T3 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ M84 ;steppers off
+ G90 ;absolute positioning
+ ;{profile_string}
+support_start.gcode =
+support_end.gcode =
+cool_start.gcode =
+cool_end.gcode =
+replace.csv =
+preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
+ ;This code is added before the T(n)
+postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
+ ;This code is added after the T(n)
+
--- /dev/null
+[info]
+name = LayWood
--- /dev/null
+[info]
+name = N-Vent
+order = 3
+
--- /dev/null
+[info]
+name = High Strength
+
+[profile]
+layer_height = .4
+wall_thickness = 1.2
+retraction_enable = True
+solid_layer_thickness = 1.2
+fill_density = 30
+nozzle_size = .6
+print_speed = 20
+print_temperature = 240
+print_temperature2 = 0
+print_temperature3 = 0
+print_temperature4 = 0
+print_bed_temperature = 110
+support = None
+platform_adhesion = None
+support_dual_extrusion = Second extruder
+wipe_tower = True
+wipe_tower_volume = 15
+ooze_shield = False
+filament_diameter = 2.89
+filament_diameter2 = 2.89
+filament_diameter3 = 0
+filament_diameter4 = 0
+filament_flow = 100.0
+retraction_speed = 10
+retraction_amount = 1
+retraction_dual_amount = 25
+retraction_min_travel = 1.5
+retraction_combing = True
+retraction_minimal_extrusion = 0.02
+retraction_hop = 0
+bottom_thickness = .5
+layer0_width_factor = 200
+object_sink = 0
+overlap_dual = 0
+travel_speed = 160
+bottom_layer_speed = 10
+infill_speed = 22
+inset0_speed = 15
+insetx_speed = 18
+cool_min_layer_time = 45
+fan_enabled = False
+skirt_line_count = 2
+skirt_gap = 6
+skirt_minimal_length = 0
+fan_full_height = .5
+fan_speed = 40
+fan_speed_max = 50
+cool_min_feedrate = 7
+cool_head_lift = False
+solid_top = True
+solid_bottom = True
+fill_overlap = 10
+support_type = Grid
+support_angle = 45
+support_fill_rate = 30
+support_xy_distance = 0
+support_z_distance = 0
+spiralize = False
+simple_mode = False
+brim_line_count = 2
+raft_margin = 3
+raft_line_spacing = 1.0
+raft_base_thickness = .5
+raft_base_linewidth = 0.7
+raft_interface_thickness = 0.2
+raft_interface_linewidth = 0.2
+raft_airgap = 0.22
+raft_surface_layers = 2
+fix_horrible_union_all_type_a = False
+fix_horrible_union_all_type_b = False
+fix_horrible_use_open_bits = False
+fix_horrible_extensive_stitching = False
+plugin_config = (lp1
+ .
+object_center_x = -1
+object_center_y = -1
+
+[alterations]
+start.gcode = ;This Gcode has been generated specifically for the LulzBot Mini
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Filament Diameter: {filament_diameter}
+ ;Nozzle Size: {nozzle_size}
+ G21 ; metric values
+ G90 ; absolute positioning
+ M82 ; set extruder to absolute mode
+ M107 ; start with the fan off
+ G92 E0 ; set extruder position to 0
+ M140 S{print_bed_temperature}; get bed heating up
+ G28 ; home all
+ M109 S140 ; set to cleaning temp and wait
+ G1 Z150 E-30 F75 ; suck up XXmm of filament
+ M109 S160 ; heat up rest of way
+ G1 X45 Y174 F11520 ; move behind scraper
+ G1 Z0 F1200 ; CRITICAL: set Z to height of top of scraper
+ G1 X45 Y174 Z-.5 F4000 ; wiping ; plunge into wipe pad
+ G1 X55 Y172 Z-.5 F4000 ; wiping
+ G1 X45 Y174 Z0 F4000 ; wiping
+ G1 X55 Y172 F4000 ; wiping
+ G1 X45 Y174 F4000 ; wiping
+ G1 X55 Y172 F4000 ; wiping
+ G1 X45 Y174 F4000 ; wiping
+ G1 X55 Y172 F4000 ; wiping
+ G1 X60 Y174 F4000 ; wiping
+ G1 X80 Y172 F4000 ; wiping
+ G1 X60 Y174 F4000 ; wiping
+ G1 X80 Y172 F4000 ; wiping
+ G1 X60 Y174 F4000 ; wiping
+ G1 X90 Y172 F4000 ; wiping
+ G1 X80 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X80 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X80 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X110 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X110 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X110 Y174 F4000 ; wiping
+ G1 X115 Y172 Z-0.5 F1000 ; wipe slower and bury noz in cleanish area
+ G1 Z10 ; raise z
+ G28 X0 Y0 ; home x and y
+ M109 S160 ; set to probing temp
+ M204 S300 ; Set probing acceleration
+ G29 ; Probe
+ M204 S2000 ; Restore standard acceleration
+ G1 X5 Y15 Z10 F5000 ; get out the way
+ G4 S1 ; pause
+ M400 ; clear buffer
+ M109 S{print_temperature} ; set extruder temp and wait
+ G4 S15 ; wait for bed to temp up
+ G1 Z2 E0 F75 ; extrude filament back into nozzle
+ M140 S{print_bed_temperature}; get bed temping up during first layer
+end.gcode = M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M104 S0 ;
+ G1 X145 Y175 Z156 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
+start2.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M104 S{print_temperature} ;Uncomment to add your own temperature line
+ ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ T1 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T0 ;Switch to the first extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Printing...
+end2.gcode = ;End GCode
+ M104 T0 S0 ;extruder heater off
+ M104 T1 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ M84 ;steppers off
+ G90 ;absolute positioning
+start3.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M104 S{print_temperature} ;Uncomment to add your own temperature line
+ ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ T2 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T1 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T0 ;Switch to the first extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Printing...
+end3.gcode = ;End GCode
+ M104 T0 S0 ;extruder heater off
+ M104 T1 S0 ;extruder heater off
+ M104 T2 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ M84 ;steppers off
+ G90 ;absolute positioning
+ ;{profile_string}
+start4.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M104 S{print_temperature} ;Uncomment to add your own temperature line
+ ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ T3 ;Switch to the 4th extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T2 ;Switch to the 3th extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T1 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T0 ;Switch to the first extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Printing...
+end4.gcode = ;End GCode
+ M104 T0 S0 ;extruder heater off
+ M104 T1 S0 ;extruder heater off
+ M104 T2 S0 ;extruder heater off
+ M104 T3 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ M84 ;steppers off
+ G90 ;absolute positioning
+ ;{profile_string}
+support_start.gcode =
+support_end.gcode =
+cool_start.gcode =
+cool_end.gcode =
+replace.csv =
+preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
+ ;This code is added before the T(n)
+postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
+ ;This code is added after the T(n)
+
--- /dev/null
+[info]
+name = Taulman Nylon 618 & Nylon 645
--- /dev/null
+[info]
+name = Fast print
+
+[profile]
+layer_height = 0.38
+wall_thickness = 1
+retraction_enable = True
+solid_layer_thickness = 1
+fill_density = 20
+nozzle_size = 0.5
+print_speed = 50
+print_temperature = 290
+print_temperature2 = 0
+print_temperature3 = 0
+print_temperature4 = 0
+print_bed_temperature = 110
+support = None
+platform_adhesion = None
+support_dual_extrusion = Both
+wipe_tower = False
+wipe_tower_volume = 15
+ooze_shield = False
+filament_diameter = 2.85
+filament_diameter2 = 0
+filament_diameter3 = 0
+filament_diameter4 = 0
+filament_flow = 100.0
+retraction_speed = 10
+retraction_amount = 1.5
+retraction_dual_amount = 16.5
+retraction_min_travel = 1.5
+retraction_combing = True
+retraction_minimal_extrusion = 0.005
+retraction_hop = 0.1
+bottom_thickness = 0.425
+layer0_width_factor = 125
+object_sink = 0.0
+overlap_dual = 0.15
+travel_speed = 175
+bottom_layer_speed = 15
+infill_speed = 40
+inset0_speed = 30
+insetx_speed = 35
+cool_min_layer_time = 20
+fan_enabled = True
+skirt_line_count = 1
+skirt_gap = 3.0
+skirt_minimal_length = 250
+fan_full_height = 0.5
+fan_speed = 0
+fan_speed_max = 0
+cool_min_feedrate = 10
+cool_head_lift = False
+solid_top = True
+solid_bottom = True
+fill_overlap = 15
+support_type = Lines
+support_angle = 45
+support_fill_rate = 30
+support_xy_distance = 0.7
+support_z_distance = 0.05
+spiralize = False
+simple_mode = False
+brim_line_count = 10
+raft_margin = 5.0
+raft_line_spacing = 3.0
+raft_base_thickness = 0.3
+raft_base_linewidth = 1.0
+raft_interface_thickness = 0.27
+raft_interface_linewidth = 0.4
+raft_airgap = 0.5
+raft_surface_layers = 2
+fix_horrible_union_all_type_a = True
+fix_horrible_union_all_type_b = False
+fix_horrible_use_open_bits = False
+fix_horrible_extensive_stitching = False
+plugin_config =
+object_center_x = -1
+object_center_y = -1
+
+[alterations]
+start.gcode = ;This Gcode has been generated specifically for the LulzBot Mini
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Filament Diameter: {filament_diameter}
+ ;Nozzle Size: {nozzle_size}
+ G21 ; metric values
+ G90 ; absolute positioning
+ M82 ; set extruder to absolute mode
+ M107 ; start with the fan off
+ G92 E0 ; set extruder position to 0
+ M140 S{print_bed_temperature}; get bed heating up
+ G28 ; home all
+ M109 S170 ; set to cleaning temp and wait
+ G1 Z150 E-30 F75 ; suck up XXmm of filament
+ M109 S180 ; heat up rest of way
+ G1 X45 Y174 F11520 ; move behind scraper
+ G1 Z0 F1200 ; CRITICAL: set Z to height of top of scraper
+ G1 X45 Y174 Z-.5 F4000 ; wiping ; plunge into wipe pad
+ G1 X55 Y172 Z-.5 F4000 ; wiping
+ G1 X45 Y174 Z0 F4000 ; wiping
+ G1 X55 Y172 F4000 ; wiping
+ G1 X45 Y174 F4000 ; wiping
+ G1 X55 Y172 F4000 ; wiping
+ G1 X45 Y174 F4000 ; wiping
+ G1 X55 Y172 F4000 ; wiping
+ G1 X60 Y174 F4000 ; wiping
+ G1 X80 Y172 F4000 ; wiping
+ G1 X60 Y174 F4000 ; wiping
+ G1 X80 Y172 F4000 ; wiping
+ G1 X60 Y174 F4000 ; wiping
+ G1 X90 Y172 F4000 ; wiping
+ G1 X80 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X80 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X80 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X110 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X110 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X110 Y174 F4000 ; wiping
+ G1 X115 Y172 Z-0.5 F1000 ; wipe slower and bury noz in cleanish area
+ G1 Z10 ; raise z
+ G28 X0 Y0 ; home x and y
+ M109 S200 ; set to probing temp
+ M204 S300 ; Set probing acceleration
+ G29 ; Probe
+ M204 S2000 ; Restore standard acceleration
+ G1 X5 Y15 Z10 F5000 ; get out the way
+ G4 S1 ; pause
+ M400 ; clear buffer
+ M109 S{print_temperature} ; set extruder temp and wait
+ G4 S15 ; wait for bed to temp up
+ G1 Z2 E0 F75 ; extrude filament back into nozzle
+ M140 S{print_bed_temperature}; get bed temping up during first layer
+end.gcode =
+ M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M104 S0 ;
+ G1 X145 Y175 Z156 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
+start2.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M104 S{print_temperature} ;Uncomment to add your own temperature line
+ ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ T1 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T0 ;Switch to the first extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Printing...
+end2.gcode = ;End GCode
+ M104 T0 S0 ;extruder heater off
+ M104 T1 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ M84 ;steppers off
+ G90 ;absolute positioning
+ ;{profile_string}
+start3.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M104 S{print_temperature} ;Uncomment to add your own temperature line
+ ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ T2 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T1 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T0 ;Switch to the first extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Printing...
+end3.gcode = ;End GCode
+ M104 T0 S0 ;extruder heater off
+ M104 T1 S0 ;extruder heater off
+ M104 T2 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ M84 ;steppers off
+ G90 ;absolute positioning
+ ;{profile_string}
+start4.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M104 S{print_temperature} ;Uncomment to add your own temperature line
+ ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ T3 ;Switch to the 4th extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T2 ;Switch to the 3th extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T1 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T0 ;Switch to the first extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Printing...
+end4.gcode = ;End GCode
+ M104 T0 S0 ;extruder heater off
+ M104 T1 S0 ;extruder heater off
+ M104 T2 S0 ;extruder heater off
+ M104 T3 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ M84 ;steppers off
+ G90 ;absolute positioning
+ ;{profile_string}
+support_start.gcode =
+support_end.gcode =
+cool_start.gcode =
+cool_end.gcode =
+replace.csv =
+preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
+ ;This code is added before the T(n)
+postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
+ ;This code is added after the T(n)
+
--- /dev/null
+[info]
+name = Polycarbonate
+order = 4
--- /dev/null
+[info]
+name = High Clarity
+
+[profile]
+layer_height = .5
+wall_thickness = 1.2
+retraction_enable = True
+solid_layer_thickness = 1.2
+fill_density = 30
+nozzle_size = .6
+print_speed = 20
+print_temperature = 240
+print_temperature2 = 0
+print_temperature3 = 0
+print_temperature4 = 0
+print_bed_temperature = 60
+support = None
+platform_adhesion = None
+support_dual_extrusion = Second extruder
+wipe_tower = True
+wipe_tower_volume = 15
+ooze_shield = False
+filament_diameter = 2.89
+filament_diameter2 = 2.89
+filament_diameter3 = 0
+filament_diameter4 = 0
+filament_flow = 100.0
+retraction_speed = 10
+retraction_amount = 1
+retraction_dual_amount = 25
+retraction_min_travel = 1.5
+retraction_combing = True
+retraction_minimal_extrusion = 0.02
+retraction_hop = 0
+bottom_thickness = .5
+layer0_width_factor = 200
+object_sink = 0
+overlap_dual = 0
+travel_speed = 160
+bottom_layer_speed = 10
+infill_speed = 22
+inset0_speed = 15
+insetx_speed = 18
+cool_min_layer_time = 45
+fan_enabled = True
+skirt_line_count = 2
+skirt_gap = 6
+skirt_minimal_length = 0
+fan_full_height = .5
+fan_speed = 40
+fan_speed_max = 50
+cool_min_feedrate = 7
+cool_head_lift = False
+solid_top = True
+solid_bottom = True
+fill_overlap = 10
+support_type = Grid
+support_angle = 45
+support_fill_rate = 30
+support_xy_distance = 0
+support_z_distance = 0
+spiralize = False
+simple_mode = False
+brim_line_count = 2
+raft_margin = 3
+raft_line_spacing = 1.0
+raft_base_thickness = .5
+raft_base_linewidth = 0.7
+raft_interface_thickness = 0.2
+raft_interface_linewidth = 0.2
+raft_airgap = 0.22
+raft_surface_layers = 2
+fix_horrible_union_all_type_a = False
+fix_horrible_union_all_type_b = False
+fix_horrible_use_open_bits = False
+fix_horrible_extensive_stitching = False
+plugin_config = (lp1
+ .
+object_center_x = -1
+object_center_y = -1
+
+[alterations]
+start.gcode = ;This Gcode has been generated specifically for the LulzBot Mini
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Filament Diameter: {filament_diameter}
+ ;Nozzle Size: {nozzle_size}
+ G21 ; metric values
+ G90 ; absolute positioning
+ M82 ; set extruder to absolute mode
+ M107 ; start with the fan off
+ G92 E0 ; set extruder position to 0
+ M140 S{print_bed_temperature}; get bed heating up
+ G28 ; home all
+ M109 S140 ; set to cleaning temp and wait
+ G1 Z150 E-30 F75 ; suck up XXmm of filament
+ M109 S160 ; heat up rest of way
+ G1 X45 Y174 F11520 ; move behind scraper
+ G1 Z0 F1200 ; CRITICAL: set Z to height of top of scraper
+ G1 X45 Y174 Z-.5 F4000 ; wiping ; plunge into wipe pad
+ G1 X55 Y172 Z-.5 F4000 ; wiping
+ G1 X45 Y174 Z0 F4000 ; wiping
+ G1 X55 Y172 F4000 ; wiping
+ G1 X45 Y174 F4000 ; wiping
+ G1 X55 Y172 F4000 ; wiping
+ G1 X45 Y174 F4000 ; wiping
+ G1 X55 Y172 F4000 ; wiping
+ G1 X60 Y174 F4000 ; wiping
+ G1 X80 Y172 F4000 ; wiping
+ G1 X60 Y174 F4000 ; wiping
+ G1 X80 Y172 F4000 ; wiping
+ G1 X60 Y174 F4000 ; wiping
+ G1 X90 Y172 F4000 ; wiping
+ G1 X80 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X80 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X80 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X110 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X110 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X110 Y174 F4000 ; wiping
+ G1 X115 Y172 Z-0.5 F1000 ; wipe slower and bury noz in cleanish area
+ G1 Z10 ; raise z
+ G28 X0 Y0 ; home x and y
+ M109 S160 ; set to probing temp
+ M204 S300 ; Set probing acceleration
+ G29 ; Probe
+ M204 S2000 ; Restore standard acceleration
+ G1 X5 Y15 Z10 F5000 ; get out the way
+ G4 S1 ; pause
+ M400 ; clear buffer
+ M109 S{print_temperature} ; set extruder temp and wait
+ G4 S15 ; wait for bed to temp up
+ G1 Z2 E0 F75 ; extrude filament back into nozzle
+ M140 S{print_bed_temperature}; get bed temping up during first layer
+end.gcode = M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M104 S0 ;
+ G1 X145 Y175 Z156 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
+start2.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M104 S{print_temperature} ;Uncomment to add your own temperature line
+ ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ T1 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T0 ;Switch to the first extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Printing...
+end2.gcode = ;End GCode
+ M104 T0 S0 ;extruder heater off
+ M104 T1 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ M84 ;steppers off
+ G90 ;absolute positioning
+start3.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M104 S{print_temperature} ;Uncomment to add your own temperature line
+ ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ T2 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T1 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T0 ;Switch to the first extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Printing...
+end3.gcode = ;End GCode
+ M104 T0 S0 ;extruder heater off
+ M104 T1 S0 ;extruder heater off
+ M104 T2 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ M84 ;steppers off
+ G90 ;absolute positioning
+ ;{profile_string}
+start4.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M104 S{print_temperature} ;Uncomment to add your own temperature line
+ ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ T3 ;Switch to the 4th extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T2 ;Switch to the 3th extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T1 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T0 ;Switch to the first extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Printing...
+end4.gcode = ;End GCode
+ M104 T0 S0 ;extruder heater off
+ M104 T1 S0 ;extruder heater off
+ M104 T2 S0 ;extruder heater off
+ M104 T3 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ M84 ;steppers off
+ G90 ;absolute positioning
+ ;{profile_string}
+support_start.gcode =
+support_end.gcode =
+cool_start.gcode =
+cool_end.gcode =
+replace.csv =
+preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
+ ;This code is added before the T(n)
+postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
+ ;This code is added after the T(n)
+
--- /dev/null
+[info]
+name = High Strength
+order = 0
+
+[profile]
+layer_height = .3
+wall_thickness = 2
+retraction_enable = True
+solid_layer_thickness = 1.2
+fill_density = 85
+nozzle_size = .5
+print_speed = 20
+print_temperature = 255
+print_temperature2 = 0
+print_temperature3 = 0
+print_temperature4 = 0
+print_bed_temperature = 60
+support = None
+platform_adhesion = None
+support_dual_extrusion = Second extruder
+wipe_tower = True
+wipe_tower_volume = 15
+ooze_shield = False
+filament_diameter = 2.89
+filament_diameter2 = 2.89
+filament_diameter3 = 0
+filament_diameter4 = 0
+filament_flow = 100.0
+retraction_speed = 10
+retraction_amount = 1
+retraction_dual_amount = 25
+retraction_min_travel = 1.5
+retraction_combing = True
+retraction_minimal_extrusion = 0.02
+retraction_hop = 0
+bottom_thickness = .425
+layer0_width_factor = 200
+object_sink = 0
+overlap_dual = 0
+travel_speed = 160
+bottom_layer_speed = 10
+infill_speed = 18
+inset0_speed = 10
+insetx_speed = 14
+cool_min_layer_time = 45
+fan_enabled = False
+skirt_line_count = 2
+skirt_gap = 6
+skirt_minimal_length = 0
+fan_full_height = .5
+fan_speed = 40
+fan_speed_max = 50
+cool_min_feedrate = 7
+cool_head_lift = False
+solid_top = True
+solid_bottom = True
+fill_overlap = 10
+support_type = Grid
+support_angle = 45
+support_fill_rate = 30
+support_xy_distance = 0
+support_z_distance = 0
+spiralize = False
+simple_mode = False
+brim_line_count = 2
+raft_margin = 3
+raft_line_spacing = 1.0
+raft_base_thickness = .5
+raft_base_linewidth = 0.7
+raft_interface_thickness = 0.2
+raft_interface_linewidth = 0.2
+raft_airgap = 0.22
+raft_surface_layers = 2
+fix_horrible_union_all_type_a = False
+fix_horrible_union_all_type_b = False
+fix_horrible_use_open_bits = False
+fix_horrible_extensive_stitching = False
+plugin_config = (lp1
+ .
+object_center_x = -1
+object_center_y = -1
+
+[alterations]
+start.gcode = ;This Gcode has been generated specifically for the LulzBot Mini
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Filament Diameter: {filament_diameter}
+ ;Nozzle Size: {nozzle_size}
+ G21 ; metric values
+ G90 ; absolute positioning
+ M82 ; set extruder to absolute mode
+ M107 ; start with the fan off
+ G92 E0 ; set extruder position to 0
+ M140 S{print_bed_temperature}; get bed heating up
+ G28 ; home all
+ M109 S140 ; set to cleaning temp and wait
+ G1 Z150 E-30 F75 ; suck up XXmm of filament
+ M109 S160 ; heat up rest of way
+ G1 X45 Y174 F11520 ; move behind scraper
+ G1 Z0 F1200 ; CRITICAL: set Z to height of top of scraper
+ G1 X45 Y174 Z-.5 F4000 ; wiping ; plunge into wipe pad
+ G1 X55 Y172 Z-.5 F4000 ; wiping
+ G1 X45 Y174 Z0 F4000 ; wiping
+ G1 X55 Y172 F4000 ; wiping
+ G1 X45 Y174 F4000 ; wiping
+ G1 X55 Y172 F4000 ; wiping
+ G1 X45 Y174 F4000 ; wiping
+ G1 X55 Y172 F4000 ; wiping
+ G1 X60 Y174 F4000 ; wiping
+ G1 X80 Y172 F4000 ; wiping
+ G1 X60 Y174 F4000 ; wiping
+ G1 X80 Y172 F4000 ; wiping
+ G1 X60 Y174 F4000 ; wiping
+ G1 X90 Y172 F4000 ; wiping
+ G1 X80 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X80 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X80 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X110 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X110 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X110 Y174 F4000 ; wiping
+ G1 X115 Y172 Z-0.5 F1000 ; wipe slower and bury noz in cleanish area
+ G1 Z10 ; raise z
+ G28 X0 Y0 ; home x and y
+ M109 S160 ; set to probing temp
+ M204 S300 ; Set probing acceleration
+ G29 ; Probe
+ M204 S2000 ; Restore standard acceleration
+ G1 X5 Y15 Z10 F5000 ; get out the way
+ G4 S1 ; pause
+ M400 ; clear buffer
+ M109 S{print_temperature} ; set extruder temp and wait
+ G4 S15 ; wait for bed to temp up
+ G1 Z2 E0 F75 ; extrude filament back into nozzle
+ M140 S{print_bed_temperature}; get bed temping up during first layer
+end.gcode = M400
+ M104 S0 ; hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E5 ; set extruder to 5mm for retract on print end
+ G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
+ M190 R50 ; wait for bed to cool
+ M104 S0 ;
+ G1 X145 Y175 Z156 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}
+start2.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M104 S{print_temperature} ;Uncomment to add your own temperature line
+ ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ T1 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T0 ;Switch to the first extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Printing...
+end2.gcode = ;End GCode
+ M104 T0 S0 ;extruder heater off
+ M104 T1 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ M84 ;steppers off
+ G90 ;absolute positioning
+start3.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M104 S{print_temperature} ;Uncomment to add your own temperature line
+ ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ T2 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T1 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T0 ;Switch to the first extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Printing...
+end3.gcode = ;End GCode
+ M104 T0 S0 ;extruder heater off
+ M104 T1 S0 ;extruder heater off
+ M104 T2 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ M84 ;steppers off
+ G90 ;absolute positioning
+ ;{profile_string}
+start4.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M104 S{print_temperature} ;Uncomment to add your own temperature line
+ ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ T3 ;Switch to the 4th extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T2 ;Switch to the 3th extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T1 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T0 ;Switch to the first extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Printing...
+end4.gcode = ;End GCode
+ M104 T0 S0 ;extruder heater off
+ M104 T1 S0 ;extruder heater off
+ M104 T2 S0 ;extruder heater off
+ M104 T3 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ M84 ;steppers off
+ G90 ;absolute positioning
+ ;{profile_string}
+support_start.gcode =
+support_end.gcode =
+cool_start.gcode =
+cool_end.gcode =
+replace.csv =
+preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
+ ;This code is added before the T(n)
+postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
+ ;This code is added after the T(n)
+
--- /dev/null
+[info]
+name = T-Glase
~ianmdlvl / cura.git / commitdiff