setting('print_temperature4', 0, int, 'basic', 'Speed & Temperature').setRange(0,340).setLabel('4th nozzle temperature (C)', 'Temperature used for printing. Set at 0 to pre-heat yourself.\nFor PLA a value of 210C is usually used.\nFor ABS a value of 230C or higher is required.')
setting('print_bed_temperature', 70, int, 'basic', 'Speed & Temperature').setRange(0,340).setLabel('Bed temperature (C)', 'Temperature used for the heated printer bed. Set at 0 to pre-heat yourself.')
setting('support', 'None', ['None', 'Touching buildplate', 'Everywhere'], 'basic', 'Support').setLabel('Support type', 'Type of support structure build.\n"Exterior only" is the most commonly used support setting.\n\nNone does not do any support.\nTouching buildplate only creates support where the support structure will touch the build platform.\nEverywhere creates support even on top of parts of the model.')
-setting('enable_raft', False, bool, 'basic', 'Support').setLabel('Enable raft', 'A raft is a few layers of lines below the bottom of the object. It prevents warping. Full raft settings can be found in the expert settings.\nFor PLA this is usually not required. But if you print with ABS it is almost required.')
+#setting('enable_raft', False, bool, 'basic', 'Support').setLabel('Enable raft', 'A raft is a few layers of lines below the bottom of the object. It prevents warping. Full raft settings can be found in the expert settings.\nFor PLA this is usually not required. But if you print with ABS it is almost required.')
setting('support_dual_extrusion', False, bool, 'basic', 'Support').setLabel('Support dual extrusion', 'Print the support material with the 2nd extruder in a dual extrusion setup. The primary extruder will be used for normal material, while the second extruder is used to print support material.')
setting('filament_diameter', 2.89, float, 'basic', 'Filament').setRange(1).setLabel('Diameter (mm)', 'Diameter of your filament, as accurately as possible.\nIf you cannot measure this value you will have to calibrate it, a higher number means less extrusion, a smaller number generates more extrusion.')
setting('filament_diameter2', 0, float, 'basic', 'Filament').setRange(0).setLabel('Diameter2 (mm)', 'Diameter of your filament for the 2nd nozzle. Use 0 to use the same diameter as for nozzle 1.')
setting('filament_diameter3', 0, float, 'basic', 'Filament').setRange(0).setLabel('Diameter3 (mm)', 'Diameter of your filament for the 3th nozzle. Use 0 to use the same diameter as for nozzle 1.')
setting('filament_diameter4', 0, float, 'basic', 'Filament').setRange(0).setLabel('Diameter4 (mm)', 'Diameter of your filament for the 4th nozzle. Use 0 to use the same diameter as for nozzle 1.')
-setting('filament_density', 1.00, float, 'basic', 'Filament').setRange(0.5,1.5).setLabel('Packing Density', 'Packing density of your filament. This should be 1.00 for PLA and 0.85 for ABS')
+setting('filament_flow', 100., float, 'basic', 'Filament').setRange(1,300).setLabel('Flow (%)', 'Flow compensation, the amount of material extruded is multiplied by this value')
+#setting('filament_density', 1.00, float, 'basic', 'Filament').setRange(0.5,1.5).setLabel('Packing Density', 'Packing density of your filament. This should be 1.00 for PLA and 0.85 for ABS')
#setting('retraction_min_travel', 5.0, float, 'advanced', 'Retraction').setRange(0).setLabel('Minimum travel (mm)', 'Minimum amount of travel needed for a retraction to happen at all. To make sure you do not get a lot of retractions in a small area')
setting('retraction_speed', 40.0, float, 'advanced', 'Retraction').setRange(0.1).setLabel('Speed (mm/s)', 'Speed at which the filament is retracted, a higher retraction speed works better. But a very high retraction speed can lead to filament grinding.')
setting('retraction_amount', 4.5, float, 'advanced', 'Retraction').setRange(0).setLabel('Distance (mm)', 'Amount of retraction, set at 0 for no retraction at all. A value of 2.0mm seems to generate good results.')
~ianmdlvl / cura.git / commitdiff