4 retraction_enable = True
5 solid_layer_thickness = .975
10 print_temperature2 = 0
11 print_temperature3 = 0
12 print_temperature4 = 0
13 print_bed_temperature = 0
15 platform_adhesion = None
16 support_dual_extrusion = Second extruder
18 wipe_tower_volume = 15
20 filament_diameter = 2.89
21 filament_diameter2 = 2.89
22 filament_diameter3 = 0
23 filament_diameter4 = 0
27 retraction_dual_amount = 25
28 retraction_min_travel = 1.5
29 retraction_combing = All
30 retraction_minimal_extrusion = 0.02
32 bottom_thickness = .325
33 layer0_width_factor = 200
37 bottom_layer_speed = 10
41 cool_min_layer_time = 45
45 skirt_minimal_length = 0
46 fan_full_height = .975
50 cool_head_lift = False
56 support_fill_rate = 30
57 support_xy_distance = 0
58 support_z_distance = 0
63 raft_line_spacing = 1.0
64 raft_base_thickness = .5
65 raft_base_linewidth = 0.7
66 raft_interface_thickness = 0.2
67 raft_interface_linewidth = 0.2
69 raft_surface_layers = 2
70 fix_horrible_union_all_type_a = False
71 fix_horrible_union_all_type_b = False
72 fix_horrible_use_open_bits = False
73 fix_horrible_extensive_stitching = False
80 start.gcode = ;Sliced at: {day} {date} {time}
81 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
82 ;Print time: {print_time}
83 ;Filament used: {filament_amount}m {filament_weight}g
84 ;Filament cost: {filament_cost}
85 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
86 ;M109 S{print_temperature} ;Uncomment to add your own temperature line
88 G90 ;absolute positioning
89 M82 ;set extruder to absolute mode
90 M107 ;start with the fan off
91 G28 X0 Y0 ;move X/Y to min endstops
92 G28 Z0 ;move Z to min endstops
93 G1 Z15.0 F{travel_speed} ;move the platform down 15mm
94 G92 E0 ;zero the extruded length
95 G1 F200 E0 ;extrude 3mm of feed stock
96 G92 E0 ;zero the extruded length again
98 M203 X192 Y208 Z3 ;speed limits
99 ;Put printing message on LCD screen
101 end.gcode = ;End GCode
102 M104 S0 ;extruder heater off
103 M140 S0 ;heated bed heater off (if you have it)
104 G91 ;relative positioning
105 G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
106 G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
107 G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
109 G90 ;absolute positioning
110 start2.gcode = ;Sliced at: {day} {date} {time}
111 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
112 ;Print time: {print_time}
113 ;Filament used: {filament_amount}m {filament_weight}g
114 ;Filament cost: {filament_cost}
115 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
116 ;M104 S{print_temperature} ;Uncomment to add your own temperature line
117 ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
118 ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
120 G90 ;absolute positioning
121 M107 ;start with the fan off
122 G28 X0 Y0 ;move X/Y to min endstops
123 G28 Z0 ;move Z to min endstops
124 G1 Z15.0 F{travel_speed} ;move the platform down 15mm
125 T1 ;Switch to the 2nd extruder
126 G92 E0 ;zero the extruded length
127 G1 F200 E10 ;extrude 10mm of feed stock
128 G92 E0 ;zero the extruded length again
129 G1 F200 E-{retraction_dual_amount}
130 T0 ;Switch to the first extruder
131 G92 E0 ;zero the extruded length
132 G1 F200 E10 ;extrude 10mm of feed stock
133 G92 E0 ;zero the extruded length again
135 ;Put printing message on LCD screen
137 end2.gcode = ;End GCode
138 M104 T0 S0 ;extruder heater off
139 M104 T1 S0 ;extruder heater off
140 M140 S0 ;heated bed heater off (if you have it)
141 G91 ;relative positioning
142 G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
143 G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
144 G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
146 G90 ;absolute positioning
147 start3.gcode = ;Sliced at: {day} {date} {time}
148 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
149 ;Print time: {print_time}
150 ;Filament used: {filament_amount}m {filament_weight}g
151 ;Filament cost: {filament_cost}
152 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
153 ;M104 S{print_temperature} ;Uncomment to add your own temperature line
154 ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
155 ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
157 G90 ;absolute positioning
158 M107 ;start with the fan off
159 G28 X0 Y0 ;move X/Y to min endstops
160 G28 Z0 ;move Z to min endstops
161 G1 Z15.0 F{travel_speed} ;move the platform down 15mm
162 T2 ;Switch to the 2nd extruder
163 G92 E0 ;zero the extruded length
164 G1 F200 E10 ;extrude 10mm of feed stock
165 G92 E0 ;zero the extruded length again
166 G1 F200 E-{retraction_dual_amount}
167 T1 ;Switch to the 2nd extruder
168 G92 E0 ;zero the extruded length
169 G1 F200 E10 ;extrude 10mm of feed stock
170 G92 E0 ;zero the extruded length again
171 G1 F200 E-{retraction_dual_amount}
172 T0 ;Switch to the first extruder
173 G92 E0 ;zero the extruded length
174 G1 F200 E10 ;extrude 10mm of feed stock
175 G92 E0 ;zero the extruded length again
177 ;Put printing message on LCD screen
179 end3.gcode = ;End GCode
180 M104 T0 S0 ;extruder heater off
181 M104 T1 S0 ;extruder heater off
182 M104 T2 S0 ;extruder heater off
183 M140 S0 ;heated bed heater off (if you have it)
184 G91 ;relative positioning
185 G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
186 G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
187 G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
189 G90 ;absolute positioning
191 start4.gcode = ;Sliced at: {day} {date} {time}
192 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
193 ;Print time: {print_time}
194 ;Filament used: {filament_amount}m {filament_weight}g
195 ;Filament cost: {filament_cost}
196 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
197 ;M104 S{print_temperature} ;Uncomment to add your own temperature line
198 ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
199 ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
200 ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
202 G90 ;absolute positioning
203 M107 ;start with the fan off
204 G28 X0 Y0 ;move X/Y to min endstops
205 G28 Z0 ;move Z to min endstops
206 G1 Z15.0 F{travel_speed} ;move the platform down 15mm
207 T3 ;Switch to the 4th extruder
208 G92 E0 ;zero the extruded length
209 G1 F200 E10 ;extrude 10mm of feed stock
210 G92 E0 ;zero the extruded length again
211 G1 F200 E-{retraction_dual_amount}
212 T2 ;Switch to the 3th extruder
213 G92 E0 ;zero the extruded length
214 G1 F200 E10 ;extrude 10mm of feed stock
215 G92 E0 ;zero the extruded length again
216 G1 F200 E-{retraction_dual_amount}
217 T1 ;Switch to the 2nd extruder
218 G92 E0 ;zero the extruded length
219 G1 F200 E10 ;extrude 10mm of feed stock
220 G92 E0 ;zero the extruded length again
221 G1 F200 E-{retraction_dual_amount}
222 T0 ;Switch to the first extruder
223 G92 E0 ;zero the extruded length
224 G1 F200 E10 ;extrude 10mm of feed stock
225 G92 E0 ;zero the extruded length again
227 ;Put printing message on LCD screen
229 end4.gcode = ;End GCode
230 M104 T0 S0 ;extruder heater off
231 M104 T1 S0 ;extruder heater off
232 M104 T2 S0 ;extruder heater off
233 M104 T3 S0 ;extruder heater off
234 M140 S0 ;heated bed heater off (if you have it)
235 G91 ;relative positioning
236 G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
237 G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
238 G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
240 G90 ;absolute positioning
242 support_start.gcode =
247 preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
248 ;This code is added before the T(n)
249 postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
250 ;This code is added after the T(n)