resources/quickprint/lulzbot_profiles/Mini_single_extruder_v2/protopasta-magnetic-iron_high-speed_Mini_single-extruder-v2_0.5noz_cura.ini

   1 [profile]
   2 layer_height = 0.38
   3 wall_thickness = 1
   4 retraction_enable = True
   5 solid_layer_thickness = 1
   6 fill_density = 20
   7 perimeter_before_infill = True
   8 nozzle_size = 0.5
   9 print_speed = 50
  10 print_temperature = 230
  11 print_temperature2 = 0
  12 print_temperature3 = 0
  13 print_temperature4 = 0
  14 print_temperature5 = 0
  15 print_bed_temperature = 60
  16 support = None
  17 platform_adhesion = None
  18 support_dual_extrusion = Both
  19 wipe_tower = False
  20 wipe_tower_volume = 15
  21 ooze_shield = False
  22 filament_diameter = 2.85
  23 filament_diameter2 = 0
  24 filament_diameter3 = 0
  25 filament_diameter4 = 0
  26 filament_diameter5 = 0
  27 filament_flow = 100.0
  28 retraction_speed = 10
  29 retraction_amount = 1.5
  30 retraction_dual_amount = 16.5
  31 retraction_min_travel = 1.5
  32 retraction_combing = All
  33 retraction_minimal_extrusion = 0.005
  34 retraction_hop = 0.1
  35 bottom_thickness = 0.425
  36 layer0_width_factor = 125
  37 object_sink = 0.0
  38 overlap_dual = 0.15
  39 travel_speed = 175
  40 bottom_layer_speed = 15
  41 infill_speed = 40
  42 solidarea_speed = 35
  43 inset0_speed = 30
  44 insetx_speed = 35
  45 cool_min_layer_time = 20
  46 fan_enabled = True
  47 skirt_line_count = 1
  48 skirt_gap = 3.0
  49 skirt_minimal_length = 250
  50 fan_full_height = 0.5
  51 fan_speed = 75
  52 fan_speed_max = 100
  53 cool_min_feedrate = 10
  54 cool_head_lift = False
  55 solid_top = True
  56 solid_bottom = True
  57 fill_overlap = 15
  58 support_type = Lines
  59 support_angle = 45
  60 support_fill_rate = 30
  61 support_xy_distance = 0.7
  62 support_z_distance = 0.05
  63 spiralize = False
  64 simple_mode = False
  65 brim_line_count = 10
  66 raft_margin = 5.0
  67 raft_line_spacing = 3.0
  68 raft_base_thickness = 0.3
  69 raft_base_linewidth = 1.0
  70 raft_interface_thickness = 0.27
  71 raft_interface_linewidth = 0.4
  72 raft_airgap_all = 0.0
  73 raft_airgap = 0.5
  74 raft_surface_layers = 2
  75 raft_surface_thickness = 0.27
  76 raft_surface_linewidth = 0.4
  77 fix_horrible_union_all_type_a = True
  78 fix_horrible_union_all_type_b = False
  79 fix_horrible_use_open_bits = False
  80 fix_horrible_extensive_stitching = False
  81 plugin_config =
  82 object_center_x = -1
  83 object_center_y = -1
  84 simplemodesettings =
  85 simplemodeprofile = 2_normal
  86 simplemodematerial = 1_pla
  87
  88 [alterations]
  89 start.gcode = ;This Gcode has been generated specifically for the LulzBot Mini
  90         ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
  91         ;Filament Diameter: {filament_diameter}
  92         ;Nozzle Size: {nozzle_size}
  93         G21                          ; metric values
  94         G90                          ; absolute positioning
  95         M82                          ; set extruder to absolute mode
  96         M107                         ; start with the fan off
  97         G92 E0                       ; set extruder position to 0
  98         M140 S{print_bed_temperature}; get bed heating up
  99         G28                          ; home all
 100         M109 S140                    ; set to cleaning temp and wait
 101         G1 Z150 E-30 F75             ; suck up XXmm of filament
 102         M109 S140                    ; heat up rest of way
 103         G1 X45 Y174 F11520           ; move behind scraper
 104         G1 Z0  F1200                 ; CRITICAL: set Z to height of top of scraper
 105         G1 X45 Y174 Z-.5 F4000       ; wiping ; plunge into wipe pad
 106         G1 X55 Y172 Z-.5 F4000       ; wiping
 107         G1 X45 Y174 Z0 F4000         ; wiping
 108         G1 X55 Y172 F4000            ; wiping
 109         G1 X45 Y174 F4000            ; wiping
 110         G1 X55 Y172 F4000            ; wiping
 111         G1 X45 Y174 F4000            ; wiping
 112         G1 X55 Y172 F4000            ; wiping
 113         G1 X60 Y174 F4000            ; wiping
 114         G1 X80 Y172 F4000            ; wiping
 115         G1 X60 Y174 F4000            ; wiping
 116         G1 X80 Y172 F4000            ; wiping
 117         G1 X60 Y174 F4000            ; wiping
 118         G1 X90 Y172 F4000            ; wiping
 119         G1 X80 Y174 F4000            ; wiping
 120         G1 X100 Y172 F4000           ; wiping
 121         G1 X80 Y174 F4000            ; wiping
 122         G1 X100 Y172 F4000           ; wiping
 123         G1 X80 Y174 F4000            ; wiping
 124         G1 X100 Y172 F4000           ; wiping
 125         G1 X110 Y174 F4000           ; wiping
 126         G1 X100 Y172 F4000           ; wiping
 127         G1 X110 Y174 F4000           ; wiping
 128         G1 X100 Y172 F4000           ; wiping
 129         G1 X110 Y174 F4000           ; wiping
 130         G1 X115 Y172 Z-0.5 F1000     ; wipe slower and bury noz in cleanish area
 131         G1 Z10                       ; raise z
 132         G28 X0 Y0                    ; home x and y
 133         M109 S140                    ; set to probing temp
 134         M204 S300                    ; Set probing acceleration
 135         G29                          ; Probe
 136         M204 S2000                   ; Restore standard acceleration
 137         G1 X5 Y15 Z10 F5000          ; get out the way
 138         G4 S1                        ; pause
 139         M400                         ; clear buffer
 140         M109 S{print_temperature}    ; set extruder temp and wait
 141         G4 S15                       ; wait for bed to temp up
 142         G1 Z2 E0 F75                 ; extrude filament back into nozzle
 143         M140 S{print_bed_temperature}; get bed temping up during first layer
 144 end.gcode =
 145         M400
 146         M104 S0                                      ; hotend off
 147         M140 S0                                      ; heated bed heater off (if you have it)
 148         M107                                         ; fans off
 149         G92 E5                                       ; set extruder to 5mm for retract on print end
 150         G1 X5 Y5 Z156 E0 F10000                      ; move to cooling positioning
 151         M190 R50                                     ; wait for bed to cool
 152         M140 S0                                      ; bed off
 153         G1 X145 Y175 Z156 F1000                      ; move to cooling positioning
 154         M84                                          ; steppers off
 155         G90                                          ; absolute positioning
 156         ;{profile_string}
 157 start2.gcode = ;Sliced at: {day} {date} {time}
 158         ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
 159         ;Print time: {print_time}
 160         ;Filament used: {filament_amount}m {filament_weight}g
 161         ;Filament cost: {filament_cost}
 162         ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
 163         ;M104 S{print_temperature} ;Uncomment to add your own temperature line
 164         ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
 165         ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
 166         G21        ;metric values
 167         G90        ;absolute positioning
 168         M107       ;start with the fan off
 169         G28 X0 Y0  ;move X/Y to min endstops
 170         G28 Z0     ;move Z to min endstops
 171         G1 Z15.0 F{travel_speed} ;move the platform down 15mm
 172         T1                      ;Switch to the 2nd extruder
 173         G92 E0                  ;zero the extruded length
 174         G1 F200 E10             ;extrude 10mm of feed stock
 175         G92 E0                  ;zero the extruded length again
 176         G1 F200 E-{retraction_dual_amount}
 177         T0                      ;Switch to the first extruder
 178         G92 E0                  ;zero the extruded length
 179         G1 F200 E10             ;extrude 10mm of feed stock
 180         G92 E0                  ;zero the extruded length again
 181         G1 F{travel_speed}
 182         ;Put printing message on LCD screen
 183         M117 Printing...
 184 end2.gcode = ;End GCode
 185         M104 T0 S0                     ;extruder heater off
 186         M104 T1 S0                     ;extruder heater off
 187         M140 S0                     ;heated bed heater off (if you have it)
 188         G91                                    ;relative positioning
 189         G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
 190         G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
 191         G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way
 192         M84                         ;steppers off
 193         G90                         ;absolute positioning
 194         ;{profile_string}
 195 start3.gcode = ;Sliced at: {day} {date} {time}
 196         ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
 197         ;Print time: {print_time}
 198         ;Filament used: {filament_amount}m {filament_weight}g
 199         ;Filament cost: {filament_cost}
 200         ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
 201         ;M104 S{print_temperature} ;Uncomment to add your own temperature line
 202         ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
 203         ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
 204         G21        ;metric values
 205         G90        ;absolute positioning
 206         M107       ;start with the fan off
 207         G28 X0 Y0  ;move X/Y to min endstops
 208         G28 Z0     ;move Z to min endstops
 209         G1 Z15.0 F{travel_speed} ;move the platform down 15mm
 210         T2                      ;Switch to the 2nd extruder
 211         G92 E0                  ;zero the extruded length
 212         G1 F200 E10             ;extrude 10mm of feed stock
 213         G92 E0                  ;zero the extruded length again
 214         G1 F200 E-{retraction_dual_amount}
 215         T1                      ;Switch to the 2nd extruder
 216         G92 E0                  ;zero the extruded length
 217         G1 F200 E10             ;extrude 10mm of feed stock
 218         G92 E0                  ;zero the extruded length again
 219         G1 F200 E-{retraction_dual_amount}
 220         T0                      ;Switch to the first extruder
 221         G92 E0                  ;zero the extruded length
 222         G1 F200 E10             ;extrude 10mm of feed stock
 223         G92 E0                  ;zero the extruded length again
 224         G1 F{travel_speed}
 225         ;Put printing message on LCD screen
 226         M117 Printing...
 227 end3.gcode = ;End GCode
 228         M104 T0 S0                     ;extruder heater off
 229         M104 T1 S0                     ;extruder heater off
 230         M104 T2 S0                     ;extruder heater off
 231         M140 S0                     ;heated bed heater off (if you have it)
 232         G91                                    ;relative positioning
 233         G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
 234         G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
 235         G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way
 236         M84                         ;steppers off
 237         G90                         ;absolute positioning
 238         ;{profile_string}
 239 start4.gcode = ;Sliced at: {day} {date} {time}
 240         ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
 241         ;Print time: {print_time}
 242         ;Filament used: {filament_amount}m {filament_weight}g
 243         ;Filament cost: {filament_cost}
 244         ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
 245         ;M104 S{print_temperature} ;Uncomment to add your own temperature line
 246         ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
 247         ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
 248         ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
 249         G21        ;metric values
 250         G90        ;absolute positioning
 251         M107       ;start with the fan off
 252         G28 X0 Y0  ;move X/Y to min endstops
 253         G28 Z0     ;move Z to min endstops
 254         G1 Z15.0 F{travel_speed} ;move the platform down 15mm
 255         T3                      ;Switch to the 4th extruder
 256         G92 E0                  ;zero the extruded length
 257         G1 F200 E10             ;extrude 10mm of feed stock
 258         G92 E0                  ;zero the extruded length again
 259         G1 F200 E-{retraction_dual_amount}
 260         T2                      ;Switch to the 3th extruder
 261         G92 E0                  ;zero the extruded length
 262         G1 F200 E10             ;extrude 10mm of feed stock
 263         G92 E0                  ;zero the extruded length again
 264         G1 F200 E-{retraction_dual_amount}
 265         T1                      ;Switch to the 2nd extruder
 266         G92 E0                  ;zero the extruded length
 267         G1 F200 E10             ;extrude 10mm of feed stock
 268         G92 E0                  ;zero the extruded length again
 269         G1 F200 E-{retraction_dual_amount}
 270         T0                      ;Switch to the first extruder
 271         G92 E0                  ;zero the extruded length
 272         G1 F200 E10             ;extrude 10mm of feed stock
 273         G92 E0                  ;zero the extruded length again
 274         G1 F{travel_speed}
 275         ;Put printing message on LCD screen
 276         M117 Printing...
 277 end4.gcode = ;End GCode
 278         M104 T0 S0                     ;extruder heater off
 279         M104 T1 S0                     ;extruder heater off
 280         M104 T2 S0                     ;extruder heater off
 281         M104 T3 S0                     ;extruder heater off
 282         M140 S0                     ;heated bed heater off (if you have it)
 283         G91                                    ;relative positioning
 284         G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
 285         G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
 286         G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way
 287         M84                         ;steppers off
 288         G90                         ;absolute positioning
 289         ;{profile_string}
 290 support_start.gcode =
 291 support_end.gcode =
 292 cool_start.gcode =
 293 cool_end.gcode =
 294 replace.csv =
 295 preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
 296         ;This code is added before the T(n)
 297 postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
 298         ;This code is added after the T(n)
 299