resources/quickprint/lulzbot_mini/T-Glase/HighClarity/profile.ini

   1 [info]
   2 name = High Clarity
   3
   4 [profile]
   5 layer_height = .5
   6 wall_thickness = 1.2
   7 retraction_enable = True
   8 solid_layer_thickness = 1.2
   9 fill_density = 30
  10 nozzle_size = .6
  11 print_speed = 20
  12 print_temperature = 240
  13 print_temperature2 = 0
  14 print_temperature3 = 0
  15 print_temperature4 = 0
  16 print_bed_temperature = 60
  17 support = None
  18 platform_adhesion = None
  19 support_dual_extrusion = Second extruder
  20 wipe_tower = True
  21 wipe_tower_volume = 15
  22 ooze_shield = False
  23 filament_diameter = 2.89
  24 filament_diameter2 = 2.89
  25 filament_diameter3 = 0
  26 filament_diameter4 = 0
  27 filament_flow = 100.0
  28 retraction_speed = 10
  29 retraction_amount = 1
  30 retraction_dual_amount = 25
  31 retraction_min_travel = 1.5
  32 retraction_combing = True
  33 retraction_minimal_extrusion = 0.02
  34 retraction_hop = 0
  35 bottom_thickness = .5
  36 layer0_width_factor = 200
  37 object_sink = 0
  38 overlap_dual = 0
  39 travel_speed = 160
  40 bottom_layer_speed = 10
  41 infill_speed = 22
  42 inset0_speed = 15
  43 insetx_speed = 18
  44 cool_min_layer_time = 45
  45 fan_enabled = True
  46 skirt_line_count = 2
  47 skirt_gap = 6
  48 skirt_minimal_length = 0
  49 fan_full_height = .5
  50 fan_speed = 40
  51 fan_speed_max = 50
  52 cool_min_feedrate = 7
  53 cool_head_lift = False
  54 solid_top = True
  55 solid_bottom = True
  56 fill_overlap = 10
  57 support_type = Grid
  58 support_angle = 45
  59 support_fill_rate = 30
  60 support_xy_distance = 0
  61 support_z_distance = 0
  62 spiralize = False
  63 simple_mode = False
  64 brim_line_count = 2
  65 raft_margin = 3
  66 raft_line_spacing = 1.0
  67 raft_base_thickness = .5
  68 raft_base_linewidth = 0.7
  69 raft_interface_thickness = 0.2
  70 raft_interface_linewidth = 0.2
  71 raft_airgap = 0.22
  72 raft_surface_layers = 2
  73 fix_horrible_union_all_type_a = False
  74 fix_horrible_union_all_type_b = False
  75 fix_horrible_use_open_bits = False
  76 fix_horrible_extensive_stitching = False
  77 plugin_config = (lp1
  78         .
  79 object_center_x = -1
  80 object_center_y = -1
  81
  82 [alterations]
  83 start.gcode = ;This Gcode has been generated specifically for the LulzBot Mini
  84         ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
  85         ;Filament Diameter: {filament_diameter}
  86         ;Nozzle Size: {nozzle_size}
  87         G21                          ; metric values
  88         G90                          ; absolute positioning
  89         M82                          ; set extruder to absolute mode
  90         M107                         ; start with the fan off
  91         G92 E0                       ; set extruder position to 0
  92         M140 S{print_bed_temperature}; get bed heating up
  93         G28                          ; home all
  94         M109 S140                    ; set to cleaning temp and wait
  95         G1 Z150 E-30 F75             ; suck up XXmm of filament
  96         M109 S160                    ; heat up rest of way
  97         G1 X45 Y174 F11520           ; move behind scraper
  98         G1 Z0  F1200                 ; CRITICAL: set Z to height of top of scraper
  99         G1 X45 Y174 Z-.5 F4000       ; wiping ; plunge into wipe pad
 100         G1 X55 Y172 Z-.5 F4000       ; wiping
 101         G1 X45 Y174 Z0 F4000         ; wiping
 102         G1 X55 Y172 F4000            ; wiping
 103         G1 X45 Y174 F4000            ; wiping
 104         G1 X55 Y172 F4000            ; wiping
 105         G1 X45 Y174 F4000            ; wiping
 106         G1 X55 Y172 F4000            ; wiping
 107         G1 X60 Y174 F4000            ; wiping
 108         G1 X80 Y172 F4000            ; wiping
 109         G1 X60 Y174 F4000            ; wiping
 110         G1 X80 Y172 F4000            ; wiping
 111         G1 X60 Y174 F4000            ; wiping
 112         G1 X90 Y172 F4000            ; wiping
 113         G1 X80 Y174 F4000            ; wiping
 114         G1 X100 Y172 F4000           ; wiping
 115         G1 X80 Y174 F4000            ; wiping
 116         G1 X100 Y172 F4000           ; wiping
 117         G1 X80 Y174 F4000            ; wiping
 118         G1 X100 Y172 F4000           ; wiping
 119         G1 X110 Y174 F4000           ; wiping
 120         G1 X100 Y172 F4000           ; wiping
 121         G1 X110 Y174 F4000           ; wiping
 122         G1 X100 Y172 F4000           ; wiping
 123         G1 X110 Y174 F4000           ; wiping
 124         G1 X115 Y172 Z-0.5 F1000     ; wipe slower and bury noz in cleanish area
 125         G1 Z10                       ; raise z
 126         G28 X0 Y0                    ; home x and y
 127         M109 S160                    ; set to probing temp
 128         M204 S300                    ; Set probing acceleration
 129         G29                          ; Probe
 130         M204 S2000                   ; Restore standard acceleration
 131         G1 X5 Y15 Z10 F5000          ; get out the way
 132         G4 S1                        ; pause
 133         M400                         ; clear buffer
 134         M109 S{print_temperature}    ; set extruder temp and wait
 135         G4 S15                       ; wait for bed to temp up
 136         G1 Z2 E0 F75                 ; extrude filament back into nozzle
 137         M140 S{print_bed_temperature}; get bed temping up during first layer
 138 end.gcode = M400
 139         M104 S0                                      ; hotend off
 140         M140 S0                                      ; heated bed heater off (if you have it)
 141         M107                                         ; fans off
 142         G92 E5                                       ; set extruder to 5mm for retract on print end
 143         G1 X5 Y5 Z156 E0 F10000                      ; move to cooling positioning
 144         M190 R50                                     ; wait for bed to cool
 145         M104 S0                                      ;
 146         G1 X145 Y175 Z156 F1000                      ; move to cooling positioning
 147         M84                                          ; steppers off
 148         G90                                          ; absolute positioning
 149         ;{profile_string}
 150 start2.gcode = ;Sliced at: {day} {date} {time}
 151         ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
 152         ;Print time: {print_time}
 153         ;Filament used: {filament_amount}m {filament_weight}g
 154         ;Filament cost: {filament_cost}
 155         ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
 156         ;M104 S{print_temperature} ;Uncomment to add your own temperature line
 157         ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
 158         ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
 159         G21        ;metric values
 160         G90        ;absolute positioning
 161         M107       ;start with the fan off
 162         G28 X0 Y0  ;move X/Y to min endstops
 163         G28 Z0     ;move Z to min endstops
 164         G1 Z15.0 F{travel_speed} ;move the platform down 15mm
 165         T1                      ;Switch to the 2nd extruder
 166         G92 E0                  ;zero the extruded length
 167         G1 F200 E10             ;extrude 10mm of feed stock
 168         G92 E0                  ;zero the extruded length again
 169         G1 F200 E-{retraction_dual_amount}
 170         T0                      ;Switch to the first extruder
 171         G92 E0                  ;zero the extruded length
 172         G1 F200 E10             ;extrude 10mm of feed stock
 173         G92 E0                  ;zero the extruded length again
 174         G1 F{travel_speed}
 175         ;Put printing message on LCD screen
 176         M117 Printing...
 177 end2.gcode = ;End GCode
 178         M104 T0 S0                     ;extruder heater off
 179         M104 T1 S0                     ;extruder heater off
 180         M140 S0                     ;heated bed heater off (if you have it)
 181         G91                                    ;relative positioning
 182         G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
 183         G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
 184         G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way
 185         M84                         ;steppers off
 186         G90                         ;absolute positioning
 187 start3.gcode = ;Sliced at: {day} {date} {time}
 188         ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
 189         ;Print time: {print_time}
 190         ;Filament used: {filament_amount}m {filament_weight}g
 191         ;Filament cost: {filament_cost}
 192         ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
 193         ;M104 S{print_temperature} ;Uncomment to add your own temperature line
 194         ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
 195         ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
 196         G21        ;metric values
 197         G90        ;absolute positioning
 198         M107       ;start with the fan off
 199         G28 X0 Y0  ;move X/Y to min endstops
 200         G28 Z0     ;move Z to min endstops
 201         G1 Z15.0 F{travel_speed} ;move the platform down 15mm
 202         T2                      ;Switch to the 2nd extruder
 203         G92 E0                  ;zero the extruded length
 204         G1 F200 E10             ;extrude 10mm of feed stock
 205         G92 E0                  ;zero the extruded length again
 206         G1 F200 E-{retraction_dual_amount}
 207         T1                      ;Switch to the 2nd extruder
 208         G92 E0                  ;zero the extruded length
 209         G1 F200 E10             ;extrude 10mm of feed stock
 210         G92 E0                  ;zero the extruded length again
 211         G1 F200 E-{retraction_dual_amount}
 212         T0                      ;Switch to the first extruder
 213         G92 E0                  ;zero the extruded length
 214         G1 F200 E10             ;extrude 10mm of feed stock
 215         G92 E0                  ;zero the extruded length again
 216         G1 F{travel_speed}
 217         ;Put printing message on LCD screen
 218         M117 Printing...
 219 end3.gcode = ;End GCode
 220         M104 T0 S0                     ;extruder heater off
 221         M104 T1 S0                     ;extruder heater off
 222         M104 T2 S0                     ;extruder heater off
 223         M140 S0                     ;heated bed heater off (if you have it)
 224         G91                                    ;relative positioning
 225         G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
 226         G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
 227         G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way
 228         M84                         ;steppers off
 229         G90                         ;absolute positioning
 230         ;{profile_string}
 231 start4.gcode = ;Sliced at: {day} {date} {time}
 232         ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
 233         ;Print time: {print_time}
 234         ;Filament used: {filament_amount}m {filament_weight}g
 235         ;Filament cost: {filament_cost}
 236         ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
 237         ;M104 S{print_temperature} ;Uncomment to add your own temperature line
 238         ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
 239         ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
 240         ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
 241         G21        ;metric values
 242         G90        ;absolute positioning
 243         M107       ;start with the fan off
 244         G28 X0 Y0  ;move X/Y to min endstops
 245         G28 Z0     ;move Z to min endstops
 246         G1 Z15.0 F{travel_speed} ;move the platform down 15mm
 247         T3                      ;Switch to the 4th extruder
 248         G92 E0                  ;zero the extruded length
 249         G1 F200 E10             ;extrude 10mm of feed stock
 250         G92 E0                  ;zero the extruded length again
 251         G1 F200 E-{retraction_dual_amount}
 252         T2                      ;Switch to the 3th extruder
 253         G92 E0                  ;zero the extruded length
 254         G1 F200 E10             ;extrude 10mm of feed stock
 255         G92 E0                  ;zero the extruded length again
 256         G1 F200 E-{retraction_dual_amount}
 257         T1                      ;Switch to the 2nd extruder
 258         G92 E0                  ;zero the extruded length
 259         G1 F200 E10             ;extrude 10mm of feed stock
 260         G92 E0                  ;zero the extruded length again
 261         G1 F200 E-{retraction_dual_amount}
 262         T0                      ;Switch to the first extruder
 263         G92 E0                  ;zero the extruded length
 264         G1 F200 E10             ;extrude 10mm of feed stock
 265         G92 E0                  ;zero the extruded length again
 266         G1 F{travel_speed}
 267         ;Put printing message on LCD screen
 268         M117 Printing...
 269 end4.gcode = ;End GCode
 270         M104 T0 S0                     ;extruder heater off
 271         M104 T1 S0                     ;extruder heater off
 272         M104 T2 S0                     ;extruder heater off
 273         M104 T3 S0                     ;extruder heater off
 274         M140 S0                     ;heated bed heater off (if you have it)
 275         G91                                    ;relative positioning
 276         G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
 277         G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
 278         G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way
 279         M84                         ;steppers off
 280         G90                         ;absolute positioning
 281         ;{profile_string}
 282 support_start.gcode =
 283 support_end.gcode =
 284 cool_start.gcode =
 285 cool_end.gcode =
 286 replace.csv =
 287 preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
 288         ;This code is added before the T(n)
 289 postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
 290         ;This code is added after the T(n)
 291