resources/quickprint/lulzbot_mini/T-Glase/HighStrength/profile.ini

   1 [info]
   2 name = High Strength
   3 order = 0
   4
   5 [profile]
   6 layer_height = .3
   7 wall_thickness = 2
   8 retraction_enable = True
   9 solid_layer_thickness = 1.2
  10 fill_density = 85
  11 nozzle_size = .5
  12 print_speed = 20
  13 print_temperature = 255
  14 print_temperature2 = 0
  15 print_temperature3 = 0
  16 print_temperature4 = 0
  17 print_bed_temperature = 60
  18 support = None
  19 platform_adhesion = None
  20 support_dual_extrusion = Second extruder
  21 wipe_tower = True
  22 wipe_tower_volume = 15
  23 ooze_shield = False
  24 filament_diameter = 2.89
  25 filament_diameter2 = 2.89
  26 filament_diameter3 = 0
  27 filament_diameter4 = 0
  28 filament_flow = 100.0
  29 retraction_speed = 10
  30 retraction_amount = 1
  31 retraction_dual_amount = 25
  32 retraction_min_travel = 1.5
  33 retraction_combing = True
  34 retraction_minimal_extrusion = 0.02
  35 retraction_hop = 0
  36 bottom_thickness = .425
  37 layer0_width_factor = 200
  38 object_sink = 0
  39 overlap_dual = 0
  40 travel_speed = 160
  41 bottom_layer_speed = 10
  42 infill_speed = 18
  43 inset0_speed = 10
  44 insetx_speed = 14
  45 cool_min_layer_time = 45
  46 fan_enabled = False
  47 skirt_line_count = 2
  48 skirt_gap = 6
  49 skirt_minimal_length = 0
  50 fan_full_height = .5
  51 fan_speed = 40
  52 fan_speed_max = 50
  53 cool_min_feedrate = 7
  54 cool_head_lift = False
  55 solid_top = True
  56 solid_bottom = True
  57 fill_overlap = 10
  58 support_type = Grid
  59 support_angle = 45
  60 support_fill_rate = 30
  61 support_xy_distance = 0
  62 support_z_distance = 0
  63 spiralize = False
  64 simple_mode = False
  65 brim_line_count = 2
  66 raft_margin = 3
  67 raft_line_spacing = 1.0
  68 raft_base_thickness = .5
  69 raft_base_linewidth = 0.7
  70 raft_interface_thickness = 0.2
  71 raft_interface_linewidth = 0.2
  72 raft_airgap = 0.22
  73 raft_surface_layers = 2
  74 fix_horrible_union_all_type_a = False
  75 fix_horrible_union_all_type_b = False
  76 fix_horrible_use_open_bits = False
  77 fix_horrible_extensive_stitching = False
  78 plugin_config = (lp1
  79         .
  80 object_center_x = -1
  81 object_center_y = -1
  82
  83 [alterations]
  84 start.gcode = ;This Gcode has been generated specifically for the LulzBot Mini
  85         ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
  86         ;Filament Diameter: {filament_diameter}
  87         ;Nozzle Size: {nozzle_size}
  88         G21                          ; metric values
  89         G90                          ; absolute positioning
  90         M82                          ; set extruder to absolute mode
  91         M107                         ; start with the fan off
  92         G92 E0                       ; set extruder position to 0
  93         M140 S{print_bed_temperature}; get bed heating up
  94         G28                          ; home all
  95         M109 S140                    ; set to cleaning temp and wait
  96         G1 Z150 E-30 F75             ; suck up XXmm of filament
  97         M109 S160                    ; heat up rest of way
  98         G1 X45 Y174 F11520           ; move behind scraper
  99         G1 Z0  F1200                 ; CRITICAL: set Z to height of top of scraper
 100         G1 X45 Y174 Z-.5 F4000       ; wiping ; plunge into wipe pad
 101         G1 X55 Y172 Z-.5 F4000       ; wiping
 102         G1 X45 Y174 Z0 F4000         ; wiping
 103         G1 X55 Y172 F4000            ; wiping
 104         G1 X45 Y174 F4000            ; wiping
 105         G1 X55 Y172 F4000            ; wiping
 106         G1 X45 Y174 F4000            ; wiping
 107         G1 X55 Y172 F4000            ; wiping
 108         G1 X60 Y174 F4000            ; wiping
 109         G1 X80 Y172 F4000            ; wiping
 110         G1 X60 Y174 F4000            ; wiping
 111         G1 X80 Y172 F4000            ; wiping
 112         G1 X60 Y174 F4000            ; wiping
 113         G1 X90 Y172 F4000            ; wiping
 114         G1 X80 Y174 F4000            ; wiping
 115         G1 X100 Y172 F4000           ; wiping
 116         G1 X80 Y174 F4000            ; wiping
 117         G1 X100 Y172 F4000           ; wiping
 118         G1 X80 Y174 F4000            ; wiping
 119         G1 X100 Y172 F4000           ; wiping
 120         G1 X110 Y174 F4000           ; wiping
 121         G1 X100 Y172 F4000           ; wiping
 122         G1 X110 Y174 F4000           ; wiping
 123         G1 X100 Y172 F4000           ; wiping
 124         G1 X110 Y174 F4000           ; wiping
 125         G1 X115 Y172 Z-0.5 F1000     ; wipe slower and bury noz in cleanish area
 126         G1 Z10                       ; raise z
 127         G28 X0 Y0                    ; home x and y
 128         M109 S160                    ; set to probing temp
 129         M204 S300                    ; Set probing acceleration
 130         G29                          ; Probe
 131         M204 S2000                   ; Restore standard acceleration
 132         G1 X5 Y15 Z10 F5000          ; get out the way
 133         G4 S1                        ; pause
 134         M400                         ; clear buffer
 135         M109 S{print_temperature}    ; set extruder temp and wait
 136         G4 S15                       ; wait for bed to temp up
 137         G1 Z2 E0 F75                 ; extrude filament back into nozzle
 138         M140 S{print_bed_temperature}; get bed temping up during first layer
 139 end.gcode = M400
 140         M104 S0                                      ; hotend off
 141         M140 S0                                      ; heated bed heater off (if you have it)
 142         M107                                         ; fans off
 143         G92 E5                                       ; set extruder to 5mm for retract on print end
 144         G1 X5 Y5 Z156 E0 F10000                      ; move to cooling positioning
 145         M190 R50                                     ; wait for bed to cool
 146         M104 S0                                      ;
 147         G1 X145 Y175 Z156 F1000                      ; move to cooling positioning
 148         M84                                          ; steppers off
 149         G90                                          ; absolute positioning
 150         ;{profile_string}
 151 start2.gcode = ;Sliced at: {day} {date} {time}
 152         ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
 153         ;Print time: {print_time}
 154         ;Filament used: {filament_amount}m {filament_weight}g
 155         ;Filament cost: {filament_cost}
 156         ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
 157         ;M104 S{print_temperature} ;Uncomment to add your own temperature line
 158         ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
 159         ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
 160         G21        ;metric values
 161         G90        ;absolute positioning
 162         M107       ;start with the fan off
 163         G28 X0 Y0  ;move X/Y to min endstops
 164         G28 Z0     ;move Z to min endstops
 165         G1 Z15.0 F{travel_speed} ;move the platform down 15mm
 166         T1                      ;Switch to the 2nd extruder
 167         G92 E0                  ;zero the extruded length
 168         G1 F200 E10             ;extrude 10mm of feed stock
 169         G92 E0                  ;zero the extruded length again
 170         G1 F200 E-{retraction_dual_amount}
 171         T0                      ;Switch to the first extruder
 172         G92 E0                  ;zero the extruded length
 173         G1 F200 E10             ;extrude 10mm of feed stock
 174         G92 E0                  ;zero the extruded length again
 175         G1 F{travel_speed}
 176         ;Put printing message on LCD screen
 177         M117 Printing...
 178 end2.gcode = ;End GCode
 179         M104 T0 S0                     ;extruder heater off
 180         M104 T1 S0                     ;extruder heater off
 181         M140 S0                     ;heated bed heater off (if you have it)
 182         G91                                    ;relative positioning
 183         G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
 184         G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
 185         G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way
 186         M84                         ;steppers off
 187         G90                         ;absolute positioning
 188 start3.gcode = ;Sliced at: {day} {date} {time}
 189         ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
 190         ;Print time: {print_time}
 191         ;Filament used: {filament_amount}m {filament_weight}g
 192         ;Filament cost: {filament_cost}
 193         ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
 194         ;M104 S{print_temperature} ;Uncomment to add your own temperature line
 195         ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
 196         ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
 197         G21        ;metric values
 198         G90        ;absolute positioning
 199         M107       ;start with the fan off
 200         G28 X0 Y0  ;move X/Y to min endstops
 201         G28 Z0     ;move Z to min endstops
 202         G1 Z15.0 F{travel_speed} ;move the platform down 15mm
 203         T2                      ;Switch to the 2nd extruder
 204         G92 E0                  ;zero the extruded length
 205         G1 F200 E10             ;extrude 10mm of feed stock
 206         G92 E0                  ;zero the extruded length again
 207         G1 F200 E-{retraction_dual_amount}
 208         T1                      ;Switch to the 2nd extruder
 209         G92 E0                  ;zero the extruded length
 210         G1 F200 E10             ;extrude 10mm of feed stock
 211         G92 E0                  ;zero the extruded length again
 212         G1 F200 E-{retraction_dual_amount}
 213         T0                      ;Switch to the first extruder
 214         G92 E0                  ;zero the extruded length
 215         G1 F200 E10             ;extrude 10mm of feed stock
 216         G92 E0                  ;zero the extruded length again
 217         G1 F{travel_speed}
 218         ;Put printing message on LCD screen
 219         M117 Printing...
 220 end3.gcode = ;End GCode
 221         M104 T0 S0                     ;extruder heater off
 222         M104 T1 S0                     ;extruder heater off
 223         M104 T2 S0                     ;extruder heater off
 224         M140 S0                     ;heated bed heater off (if you have it)
 225         G91                                    ;relative positioning
 226         G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
 227         G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
 228         G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way
 229         M84                         ;steppers off
 230         G90                         ;absolute positioning
 231         ;{profile_string}
 232 start4.gcode = ;Sliced at: {day} {date} {time}
 233         ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
 234         ;Print time: {print_time}
 235         ;Filament used: {filament_amount}m {filament_weight}g
 236         ;Filament cost: {filament_cost}
 237         ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
 238         ;M104 S{print_temperature} ;Uncomment to add your own temperature line
 239         ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
 240         ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
 241         ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
 242         G21        ;metric values
 243         G90        ;absolute positioning
 244         M107       ;start with the fan off
 245         G28 X0 Y0  ;move X/Y to min endstops
 246         G28 Z0     ;move Z to min endstops
 247         G1 Z15.0 F{travel_speed} ;move the platform down 15mm
 248         T3                      ;Switch to the 4th extruder
 249         G92 E0                  ;zero the extruded length
 250         G1 F200 E10             ;extrude 10mm of feed stock
 251         G92 E0                  ;zero the extruded length again
 252         G1 F200 E-{retraction_dual_amount}
 253         T2                      ;Switch to the 3th extruder
 254         G92 E0                  ;zero the extruded length
 255         G1 F200 E10             ;extrude 10mm of feed stock
 256         G92 E0                  ;zero the extruded length again
 257         G1 F200 E-{retraction_dual_amount}
 258         T1                      ;Switch to the 2nd extruder
 259         G92 E0                  ;zero the extruded length
 260         G1 F200 E10             ;extrude 10mm of feed stock
 261         G92 E0                  ;zero the extruded length again
 262         G1 F200 E-{retraction_dual_amount}
 263         T0                      ;Switch to the first extruder
 264         G92 E0                  ;zero the extruded length
 265         G1 F200 E10             ;extrude 10mm of feed stock
 266         G92 E0                  ;zero the extruded length again
 267         G1 F{travel_speed}
 268         ;Put printing message on LCD screen
 269         M117 Printing...
 270 end4.gcode = ;End GCode
 271         M104 T0 S0                     ;extruder heater off
 272         M104 T1 S0                     ;extruder heater off
 273         M104 T2 S0                     ;extruder heater off
 274         M104 T3 S0                     ;extruder heater off
 275         M140 S0                     ;heated bed heater off (if you have it)
 276         G91                                    ;relative positioning
 277         G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
 278         G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
 279         G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way
 280         M84                         ;steppers off
 281         G90                         ;absolute positioning
 282         ;{profile_string}
 283 support_start.gcode =
 284 support_end.gcode =
 285 cool_start.gcode =
 286 cool_end.gcode =
 287 replace.csv =
 288 preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
 289         ;This code is added before the T(n)
 290 postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
 291         ;This code is added after the T(n)
 292