Used internally. A GET/SET operation for it won't change or return anything.

Interpret the cache of data, build either a traditional frontend tunerequest so we can pass validation in the FE_SET_FRONTEND ioctl.

Reset a cache of data specific to the frontend here. This does not effect hardware.

Central frequency of the channel, in HZ.

Notes:

1)For ISDB-T, the channels are usually transmitted with an offset of 143kHz. E.g. a valid frequncy could be 474143 kHz. The stepping is bound to the bandwidth of the channel which is 6MHz.

2)As in ISDB-Tsb the channel consists of only one or three segments the frequency step is 429kHz, 3*429 respectively. As for ISDB-T the central frequency of the channel is expected.

Specifies the frontend modulation type for cable and satellite types. The modulation can be one of the types bellow:

 typedef enum fe_modulation {
	QPSK,
	QAM_16,
	QAM_32,
	QAM_64,
	QAM_128,
	QAM_256,
	QAM_AUTO,
	VSB_8,
	VSB_16,
	PSK_8,
	APSK_16,
	APSK_32,
	DQPSK,
 } fe_modulation_t;

Bandwidth for the channel, in HZ.

Possible values: 1712000, 5000000, 6000000, 7000000, 8000000, 10000000.

Notes:

1) For ISDB-T it should be always 6000000Hz (6MHz)

2) For ISDB-Tsb it can vary depending on the number of connected segments

3) Bandwidth doesn't apply for DVB-C transmissions, as the bandwidth for DVB-C depends on the symbol rate

4) Bandwidth in ISDB-T is fixed (6MHz) or can be easily derived from other parameters (DTV_ISDBT_SB_SEGMENT_IDX, DTV_ISDBT_SB_SEGMENT_COUNT).

5) DVB-T supports 6, 7 and 8MHz.

6) In addition, DVB-T2 supports 1.172, 5 and 10MHz.

The Inversion field can take one of these values:

	typedef enum fe_spectral_inversion {
		INVERSION_OFF,
		INVERSION_ON,
		INVERSION_AUTO
	} fe_spectral_inversion_t;
	

It indicates if spectral inversion should be presumed or not. In the automatic setting (INVERSION_AUTO) the hardware will try to figure out the correct setting by itself.

Currently not implemented.

Digital TV symbol rate, in bauds (symbols/second). Used on cable standards.

Used cable/satellite transmissions. The acceptable values are:

typedef enum fe_code_rate {
	FEC_NONE = 0,
	FEC_1_2,
	FEC_2_3,
	FEC_3_4,
	FEC_4_5,
	FEC_5_6,
	FEC_6_7,
	FEC_7_8,
	FEC_8_9,
	FEC_AUTO,
	FEC_3_5,
	FEC_9_10,
} fe_code_rate_t;
	

which correspond to error correction rates of 1/2, 2/3, etc., no error correction or auto detection.

The voltage is usually used with non-DiSEqC capable LNBs to switch the polarzation (horizontal/vertical). When using DiSEqC epuipment this voltage has to be switched consistently to the DiSEqC commands as described in the DiSEqC spec.

		typedef enum fe_sec_voltage {
		SEC_VOLTAGE_13,
		SEC_VOLTAGE_18
		} fe_sec_voltage_t;
	

Currently not used.

Sets DVB-S2 pilot

typedef enum fe_pilot {
	PILOT_ON,
	PILOT_OFF,
	PILOT_AUTO,
} fe_pilot_t;
		

Sets DVB-S2 rolloff

typedef enum fe_rolloff {
	ROLLOFF_35, /* Implied value in DVB-S, default for DVB-S2 */
	ROLLOFF_20,
	ROLLOFF_25,
	ROLLOFF_AUTO,
} fe_rolloff_t;
		

Currently not implemented.

Currently not implemented.

Currently not implemented.

Specifies the type of Delivery system

typedef enum fe_delivery_system {
	SYS_UNDEFINED,
	SYS_DVBC_ANNEX_AC,
	SYS_DVBC_ANNEX_B,
	SYS_DVBT,
	SYS_DSS,
	SYS_DVBS,
	SYS_DVBS2,
	SYS_DVBH,
	SYS_ISDBT,
	SYS_ISDBS,
	SYS_ISDBC,
	SYS_ATSC,
	SYS_ATSCMH,
	SYS_DMBTH,
	SYS_CMMB,
	SYS_DAB,
	SYS_DVBT2,
	SYS_TURBO,
} fe_delivery_system_t;

If DTV_ISDBT_SOUND_BROADCASTING is '0' this bit-field represents whether the channel is in partial reception mode or not.

If '1' DTV_ISDBT_LAYERA_* values are assigned to the center segment and DTV_ISDBT_LAYERA_SEGMENT_COUNT has to be '1'.

If in addition DTV_ISDBT_SOUND_BROADCASTING is '1' DTV_ISDBT_PARTIAL_RECEPTION represents whether this ISDB-Tsb channel is consisting of one segment and layer or three segments and two layers.

Possible values: 0, 1, -1 (AUTO)

This field represents whether the other DTV_ISDBT_*-parameters are referring to an ISDB-T and an ISDB-Tsb channel. (See also DTV_ISDBT_PARTIAL_RECEPTION).

Possible values: 0, 1, -1 (AUTO)

This field only applies if DTV_ISDBT_SOUND_BROADCASTING is '1'.

(Note of the author: This might not be the correct description of the SUBCHANNEL-ID in all details, but it is my understanding of the technical background needed to program a device)

An ISDB-Tsb channel (1 or 3 segments) can be broadcasted alone or in a set of connected ISDB-Tsb channels. In this set of channels every channel can be received independently. The number of connected ISDB-Tsb segment can vary, e.g. depending on the frequency spectrum bandwidth available.

Example: Assume 8 ISDB-Tsb connected segments are broadcasted. The broadcaster has several possibilities to put those channels in the air: Assuming a normal 13-segment ISDB-T spectrum he can align the 8 segments from position 1-8 to 5-13 or anything in between.

The underlying layer of segments are subchannels: each segment is consisting of several subchannels with a predefined IDs. A sub-channel is used to help the demodulator to synchronize on the channel.

An ISDB-T channel is always centered over all sub-channels. As for the example above, in ISDB-Tsb it is no longer as simple as that.

The DTV_ISDBT_SB_SUBCHANNEL_ID parameter is used to give the sub-channel ID of the segment to be demodulated.

Possible values: 0 .. 41, -1 (AUTO)

This field only applies if DTV_ISDBT_SOUND_BROADCASTING is '1'.

DTV_ISDBT_SB_SEGMENT_IDX gives the index of the segment to be demodulated for an ISDB-Tsb channel where several of them are transmitted in the connected manner.

Possible values: 0 .. DTV_ISDBT_SB_SEGMENT_COUNT - 1

Note: This value cannot be determined by an automatic channel search.

This field only applies if DTV_ISDBT_SOUND_BROADCASTING is '1'.

DTV_ISDBT_SB_SEGMENT_COUNT gives the total count of connected ISDB-Tsb channels.

Possible values: 1 .. 13

Note: This value cannot be determined by an automatic channel search.

ISDB-T channels can be coded hierarchically. As opposed to DVB-T in ISDB-T hierarchical layers can be decoded simultaneously. For that reason a ISDB-T demodulator has 3 viterbi and 3 reed-solomon-decoders.

ISDB-T has 3 hierarchical layers which each can use a part of the available segments. The total number of segments over all layers has to 13 in ISDB-T.

There are 3 parameter sets, for Layers A, B and C.

Returns the major/minor version of the DVB API

Used on terrestrial transmissions. The acceptable values are:

typedef enum fe_code_rate {
	FEC_NONE = 0,
	FEC_1_2,
	FEC_2_3,
	FEC_3_4,
	FEC_4_5,
	FEC_5_6,
	FEC_6_7,
	FEC_7_8,
	FEC_8_9,
	FEC_AUTO,
	FEC_3_5,
	FEC_9_10,
} fe_code_rate_t;
	

Used on terrestrial transmissions. The acceptable values are:

typedef enum fe_code_rate {
	FEC_NONE = 0,
	FEC_1_2,
	FEC_2_3,
	FEC_3_4,
	FEC_4_5,
	FEC_5_6,
	FEC_6_7,
	FEC_7_8,
	FEC_8_9,
	FEC_AUTO,
	FEC_3_5,
	FEC_9_10,
} fe_code_rate_t;
	

Possible values are:

typedef enum fe_guard_interval {
	GUARD_INTERVAL_1_32,
	GUARD_INTERVAL_1_16,
	GUARD_INTERVAL_1_8,
	GUARD_INTERVAL_1_4,
	GUARD_INTERVAL_AUTO,
	GUARD_INTERVAL_1_128,
	GUARD_INTERVAL_19_128,
	GUARD_INTERVAL_19_256,
} fe_guard_interval_t;

Notes:

1) If DTV_GUARD_INTERVAL is set the GUARD_INTERVAL_AUTO the hardware will try to find the correct guard interval (if capable) and will use TMCC to fill in the missing parameters.

2) Intervals 1/128, 19/128 and 19/256 are used only for DVB-T2 at present

Specifies the number of carriers used by the standard

Possible values are:

typedef enum fe_transmit_mode {
	TRANSMISSION_MODE_2K,
	TRANSMISSION_MODE_8K,
	TRANSMISSION_MODE_AUTO,
	TRANSMISSION_MODE_4K,
	TRANSMISSION_MODE_1K,
	TRANSMISSION_MODE_16K,
	TRANSMISSION_MODE_32K,
} fe_transmit_mode_t;

Notes:

1) ISDB-T supports three carrier/symbol-size: 8K, 4K, 2K. It is called 'mode' in the standard: Mode 1 is 2K, mode 2 is 4K, mode 3 is 8K

2) If DTV_TRANSMISSION_MODE is set the TRANSMISSION_MODE_AUTO the hardware will try to find the correct FFT-size (if capable) and will use TMCC to fill in the missing parameters.

3) DVB-T specifies 2K and 8K as valid sizes.

4) DVB-T2 specifies 1K, 2K, 4K, 8K, 16K and 32K.

Frontend hierarchy

typedef enum fe_hierarchy {
	 HIERARCHY_NONE,
	 HIERARCHY_1,
	 HIERARCHY_2,
	 HIERARCHY_4,
	 HIERARCHY_AUTO
 } fe_hierarchy_t;
	

Currently unused.

DVB-T2 supports Physical Layer Pipes (PLP) to allow transmission of many data types via a single multiplex. The API will soon support this at which point this section will be expanded.

The following parameters are valid for DVB-T:

DVB-T2 support is currently in the early stages of development, so expect that this section maygrow and become more detailed with time.

The following parameters are valid for DVB-T2:

This ISDB-T/ISDB-Tsb API extension should reflect all information needed to tune any ISDB-T/ISDB-Tsb hardware. Of course it is possible that some very sophisticated devices won't need certain parameters to tune.

The information given here should help application writers to know how to handle ISDB-T and ISDB-Tsb hardware using the Linux DVB-API.

The details given here about ISDB-T and ISDB-Tsb are just enough to basically show the dependencies between the needed parameter values, but surely some information is left out. For more detailed information see the following documents:

ARIB STD-B31 - "Transmission System for Digital Terrestrial Television Broadcasting" and

ARIB TR-B14 - "Operational Guidelines for Digital Terrestrial Television Broadcasting".

In order to understand the ISDB specific parameters, one has to have some knowledge the channel structure in ISDB-T and ISDB-Tsb. I.e. it has to be known to the reader that an ISDB-T channel consists of 13 segments, that it can have up to 3 layer sharing those segments, and things like that.

The following parameters are valid for ISDB-T:

The following parameters are valid for ATSC:

The DVB-C Annex-A/C is the widely used cable standard. Transmission uses QAM modulation.

The following parameters are valid for DVB-C Annex A/C:

The DVB-C Annex-B is only used on a few Countries like the United States.

The following parameters are valid for DVB-C Annex B:

The following parameters are valid for DVB-S:

Future implementations might add those two missing parameters:

In addition to all parameters valid for DVB-S, DVB-S2 supports the following parameters:

In addition to all parameters valid for DVB-S, turbo code supports the following parameters:

The following parameters are valid for ISDB-S: