+udev is targeted at Linux kernels 2.6 and beyond to provide a userspace solution for a dynamic /dev directory, with persistent device naming. The previous /dev implementation, devfs, is now deprecated, and udev is seen as the successor. udev vs devfs is a sensitive area of conversation - you should read this document before making comparisons. +
-I'm all open to feedback - please contact me with any comments, problems, and suggested improvements.+Over the years, the things that you might use udev rules for has changed, as well as the flexibility of rules themselves. On a modern system, udev provides persistent naming for some device types out-of-the-box, eliminating the need for custom rules for those devices. However, some users will still require the extra level of customisation. +
-This document assumes that you have udev/hotplug installed and running OK with default configurations. If you do not yet have udev configured and running, I would suggest that you follow Decibels udev Primer to get to this stage (contains some Gentoo Linux specifics, but should be useful for other distro's too).+This document assumes that you have udev installed and running OK with default configurations. This is usually handled by your Linux distribution. +
- ++This document does not cover every single detail of rule writing, but does aim to introduce all of the main concepts. The finer details can be found in the udev man page. +
-+This document uses various examples (many of which are entirely fictional) to illustrate ideas and concepts. Not all syntax is explicitly described in the accompanying text, be sure to look at the example rules to get a complete understanding. +
-April 6th 2004: I now write suggest users to use their own "local.rules" file rather than prepending "udev.rules".+A basic introduction only, might not be totally accurate. +
-The original /dev directories were just populated with every device that might possibly appear in the system. /dev directories were typically very large because of this. devfs came along to provide a more managable approach (noticably, it only populated /dev with hardware that is plugged into the system), as well as some other functionality, but the system proved to have problems which could not be easily fixed.+On typical Linux-based systems, the /dev directory is used to store file-like device nodes which refer to certain devices in the system. Each node points to a part of the system (a device), which might or might not exist. Userspace applications can use these device nodes to interface with the systems hardware, for example, the X server will "listen to" /dev/input/mice so that it can relate the user's mouse movements to moving the visual mouse pointer. +
-udev is the "new" way of managing /dev directories, designed to clear up some issues with previous /dev implementations, and provide a robust path forward. In order to create and name /dev device nodes corresponding to devices that are present in the system, udev relies on matching information provided by sysfs with rules provided by the user. This documentation aims to detail the process of rule-writing, one of the only udev-related tasks that must (optionally) be performed by the user.+The original /dev directories were just populated with every device that might possibly appear in the system. /dev directories were typically very large because of this. devfs came along to provide a more manageable approach (noticeably, it only populated /dev with hardware that is plugged into the system), as well as some other functionality, but the system proved to have problems which could not be easily fixed. +
-sysfs is a new filesystem to the 2.6 kernels. It is managed by the kernel, and exports basic information about the devices currently plugged into your system. udev can use this information to create device nodes corresponding to your hardware. sysfs is mounted at /sys and is browsable. You may wish to investigate some of the files stored there before getting to grips with udev. Throughout this document, I will use the terms /sys and SYSFS interchangeably.+udev is the "new" way of managing /dev directories, designed to clear up some issues with previous /dev implementations, and provide a robust path forward. In order to create and name /dev device nodes corresponding to devices that are present in the system, udev relies on matching information provided by sysfs with rules provided by the user. This documentation aims to detail the process of rule-writing, one of the only udev-related tasks that must (optionally) be performed by the user. +
+ ++sysfs is a new filesystem to the 2.6 kernels. It is managed by the kernel, and exports basic information about the devices currently plugged into your system. udev can use this information to create device nodes corresponding to your hardware. sysfs is mounted at /sys and is browseable. You may wish to investigate some of the files stored there before getting to grips with udev. Throughout this document, I will use the terms /sys and sysfs interchangeably. +
-+udev rules are flexible and very powerful. Here are some of the things you can use rules to achieve: +
+ ++Writing rules is not a workaround for the problem where no device nodes for your particular device exist. Even if there are no matching rules, udev will create the device node with the default name supplied by the kernel. +
+ ++Having persistently named device nodes has several advantages. Assume you own two USB storage devices: a digital camera and a USB flash disk. These devices are typically assigned device nodes /dev/sda and /dev/sdb but the exact assignment depends on the order which they were originally connected. This may cause problems to some users, who would benefit greatly if each device could be named persistently every time, e.g. /dev/camera and /dev/flashdisk. +
+ + ++udev provides persistent naming for some device types out of the box. This is a very useful feature, and in many circumstances means that your journey ends here: you do not have to write any rules. +
-However, udev allows you to customise the naming of device nodes. There are two reasons why you might want to do this: convenience, and persistant naming.+udev provides out-of-the-box persistent naming for storage devices in the /dev/disk directory. To view the persistent names which have been created for your storage hardware, you can use the following command: +
-Take the example of using udev, so that when your printer is plugged in, it gets named as /dev/printer and also as the usual /dev/lp0. It's not only convenience (e.g. reading and interpreting "printer" as opposed to "lp0"), its a solution for non-persistant naming. Say that I have two printers - a HP laser printer and an Epson inkjet. When they are both plugged in and on, I have /dev/lp0 and /dev/lp1.-How do I know which node refers to which printer? There is no easy way. The first printer that got connected was assigned name "lp0", and the second "lp1". Plugging in my printers in a different order would swap the names here, and that would mess up my scripts that always expect my HP laser printer to be lp1.# ls -lR /dev/disk
+This works for all storage types. As an example, udev has created /dev/disk/by-id/scsi-SATA_ST3120827AS_4MS1NDXZ-part3 which is a persistent-named symbolic link to my root partition. udev creates /dev/disk/by-id/usb-Prolific_Technology_Inc._USB_Mass_Storage_Device-part1 when I plug my USB flash disk in, which is also a persistent name. +
-However, if my HP laser printer got named lp_hp (as well as lpX) and my other printer got named lp_epson (as well as lpY), then my scripts could just refer to those names. udev magic can control this and ensure that these persistant names always point to the device that I intended.+When deciding how to name a device and which additional actions to perform, udev reads a series of rules files. These files are kept in the /etc/udev/rules.d directory, and they all must have the .rules suffix. +
-Default udev rules are stored in /etc/udev/udev.rules. You may find it interesting to look over this file - it includes a few examples, and then some default rules proving a devfs-style /dev layout. However, you should not write rules into this file directly, to reduce hassle while updating your udev installation in the future.+Default udev rules are stored in /etc/udev/rules.d/50-udev.rules. You may find it interesting to look over this file - it includes a few examples, and then some default rules proving a devfs-style /dev layout. However, you should not write rules into this file directly. +
-Files in /etc/udev are parsed in lexical order. udev will stop processing rules as soon as it finds a matching rule in a file for the new item of hardware that has been detected. It is important that your own rules get processed before the udev defaults, otherwise your own naming schemes will not take effect! I suggest that you keep your own rules in a file at /etc/udev/local.rules (this doesn't exist by default - create it). As L comes before U, you know that your rules will be looked at first.+Files in /etc/udev/rules.d/ are parsed in lexical order, and in some circumstances, the order in which rules are parsed is important. In general, you want your own rules to be parsed before the defaults, so I suggest you create a file at /etc/udev/rules.d/10-local.rules and write all your rules into this file. +
-As your own rules will effectively mask out the udev defaults which create the base /dev layout, it is recommended that you also specify devfs-style names/symlinks for the rules you write, so that you get the sensible defaults plus your own names.+In a rules file, lines starting with "#" are treated as comments. Every other non-blank line is a rule. Rules cannot span multiple lines. +
-In rule files, lines starting with a "#" are treated as comments. Every uncommented line in the file corresponds to a rule.+One device can be matched by more than one rule. This has it's practical advantages, for example, we can write two rules which match the same device, where each one provides its own alternate name for the device. Both alternate names will be created, even if the rules are in separate files. It is important to understand that udev will not stop processing when it finds a matching rule, it will continue searching and attempt to apply every rule that it knows about. +
-The basic form for a rule is: -key,[key,...] name [, symlink]+ +
+Each rule is constructed from a series of key-value pairs, which are separated by commas. match keys are conditions used to identify the device which the rule is acting upon. When all match keys in a rule correspond to the device being handled, then the rule is applied and the actions of the assignment keys are invoked. Every rule should consist of at least one match key and at least one assignment key. +
-Remember that udev will only create one node for one device. If you want it to be accessible through multiple nodes, then you have to specify the other nodes in the SYMLINK parameter.+Here is an example rule to illustrate the above: +
-I'll take a slightly modified udev example rule to illustrate this: -BUS="usb", SYSFS{serial}="HXOLL0012202323480", NAME="lp_epson", SYMLINK="printers/epson_stylus"-The keys here are the BUS and SYSFS{serial} parameters. udev will match this rule against a device that is connected through the USB bus and with a serial number of HXOLL0012202323480. Note that all (as opposed to any) specified keys must be matched for udev to use the rule to name a device.KERNEL=="hdb", NAME="my_spare_disk"
+The above rule includes one match key (KERNEL) and one assignment key (NAME). The semantics of these keys and their properties will be detailed later. It is important to note that the match key is related to its value through the equality operator (==), whereas the assignment key is related to its value through the assignment operator (=). +
-udev will name this node lp_epson, and it will be located at /dev/lp_epson.+udev provides several different match keys which can be used to write rules which match devices very precisely. Some of the most common keys are introduced below, others will be introduced later in this document. For a complete list, see the udev man page. +
-In the NAME and SYMLINK parameters of your rules, you are able to use basic operators to assist the naming of devices. Hackers will know this sort of thing as printf-like string substitution. ++After you have used a series of match keys to precisely match a device, udev gives you fine control over what happens next, through a range of assignment keys. For a complete list of possible assignment keys, see the udev man page. The most basic assignment keys are introduced below. Others will be introduced later in this document. +
-BUS="usb", SYSFS{vendor}="FUJIFILM", SYSFS{model}="M100", NAME="camera%n"+As hinted above, udev only creates one true device node for one device. If you wish to provide alternate names for this device node, you use the symbolic link functionality. With the SYMLINK assignment, you are actually maintaining a list of symbolic links, all of which will be pointed at the real device node. To manipulate these links, we introduce a new operator for appending to lists: +=. You can append multiple symlinks to the list from any one rule by separating each one with a space. +
-Another common operator is %k. This represents what the kernel would name the device, e.g. "hda1". You may often see rules which have NAME="%k" to produce the default names for the hardware. In these rules, customisation is usually done through the SYMLINK parameter.-A full list of operators, with explanations, can be found in the udev man page.KERNEL=="hdb", NAME="my_spare_disk"
+The above rule says: match a device which was named by the kernel as hdb, and instead of calling it hdb, name the device node as my_spare_disk. The device node appears at /dev/my_spare_disk. +
- --You can use wildcards and basic regular-expression style matching to provide even more flexibility when writing keys. Taking a default udev rule: +KERNEL=="hdb", DRIVER=="ide-disk", SYMLINK+="sparedisk"
+The above rule says: match a device which was named by the kernel as hdb AND where the driver is ide-disk. Name the device node with the default name and create a symbolic link to it named sparedisk. Note that we did not specify a device node name, so udev uses the default. In order to preserve the standard /dev layout, your own rules will typically leave the NAME alone but create some SYMLINKs and/or perform other assignments. +
-+KERNEL="ts*", NAME="input/%k"
-The * operator is used here, which matches literally anything - zero, one, or more characters of any kind. The rule literally says:KERNEL=="hdc", SYMLINK+="cdrom cdrom0"
+The above rule is probably more typical of the types of rules you might be writing. It creates two symbolic links at /dev/cdrom and /dev/cdrom0, both of which point at /dev/hdc. Again, no NAME assignment was specified, so the default kernel name (hdc) is used. +
-Match a device identified by a KERNEL name starting with the letters "ts" optionally followed by anything at all, and name it with the KERNEL name (%k) under the input directory.+ +
+The match keys introduced so far only provide limited matching capabilities. Realistically we require much finer control: we want to identify devices based on advanced properties such as vendor codes, exact product numbers, serial numbers, storage capacities, number of partitions, etc. +
-You can also use square brackets [ ] to match any single character. Direct quote from udev man page:For example, the pattern string "tty[SR]" would match either "ttyS" or "ttyR".+
+Many drivers export information like this into sysfs, and udev allows us to incorporate sysfs-matching into our rules, using the SYSFS key with a slightly different syntax. +
-You can also specify ranges that can be matched, e.g. [0-9] would match any single digit. Using an example rule from a default udev installation: ++Here are some examples of rules which match data from sysfs. Further detail will be provided later in this document which will aid you in writing rules based on sysfs attributes. +
-+KERNEL="fd[0-9]*", NAME="floppy/%n"
+KERNEL=="sda", SYSFS{model}=="ST3120827AS", SYMLINK+="my_hard_disk"
+SUBSYSTEM=="block", SYSFS{size}=="234441648", SYMLINK+="my_disk"
+BUS=="usb", SYSFS{manufacturer}=="OLYMPUS", SYSFS{product}=="X250,D560Z,C350Z", SYMLINK+="camera"
+Match a device identified by a KERNEL name starting with the letters "fd", followed by any single digit, optionally followed by anything at all. Name the device with the kernel number of the device (%n) under the floppy directory.+
+When writing rules which will potentially handle multiple similar devices, udev's printf-like string substitution operators are very useful. You can simply include these operators in any assignments your rule makes, and udev will evaluate them when they are executed. +
-You can use these wildcards/regular-expression matches in any type of key, including both basic keys and sysfs-based identification (see below for explanations of these key types).+The most common operators are %k and %n. %k evaluates to the kernel name for the device, e.g. "sda3" for a device that would (by default) appear at /dev/sda3. %n evaluates to the kernel number for the device (the partition number for storage devices), e.g. "3" for /dev/sda3. +
-I have purposely left out some information on this topic (particularly the flexibility of using [ ] operators) that is out of the scope of basic rule-writing documentation. More information on this topic can be found in the udev man page.+udev also provides several other substitution operators for more advanced functionality. Consult the udev man page after reading the rest of this document. There is also an alternative syntax for these operators - $kernel and $number for the examples above. For this reason, if you wish to match a literal % in a rule then you must write %%, and if you wish to match a literal $ then you must write $$. +
- -+To illustrate the concept of string substitution, some example rules are shown below. +
-udev provides a few basic key matching methods, and also provides flexible ways of matching information in SYSFS. A typical rule will match both normal keys (e.g. BUS and KERNEL), as well as SYSFS keys to differentiate between different hardware plugged in throught the same port.-You may be wondering, "How do I find the serial number of my printer? What is the model of my camera?". Rule writing isn't as hard as it sounds. The trickiest bit is finding your device in /sys, and deciding which info to use.+KERNEL=="mice", NAME="input/%k" +KERNEL=="loop0", NAME="loop/%n", SYMLINK+="%k" +
+The first rule ensures that the mice device node appears exclusively in the /dev/input directory (by default it would be at /dev/mice). The second rule ensures that the device node named loop0 is created at /dev/loop/0 but also creates a symbolic link at /dev/loop0 as usual. +
- -+The use of the above rules is questionable, as they all could be rewritten without using any substitution operators. The true power of these substitutions will become apparent in the next section. +
-See the udev man page for more info on these keys.+As well as matching strings exactly, udev allows you to use shell-style pattern matching. There are 3 patterns supported: +
+- -Some snipped output of the results of my "udevinfo -a -p /sys/block/sda" command is shown below, with colour added.# udevinfo -a -p /sys/path/to/hardware/info
-follow the class device's "device"
- looking at the device chain at '/sys/devices/pci0000:00/0000:00:02.1/usb3/3-3/3-3:1.0/host0/0:0:0:0':
- BUS="scsi"
- ID="0:0:0:0"
- SYSFS{detach_state}="0"
- SYSFS{type}="0"
- SYSFS{max_sectors}="240"
- SYSFS{device_blocked}="0"
- SYSFS{queue_depth}="1"
- SYSFS{scsi_level}="3"
- SYSFS{vendor}=" "
- SYSFS{model}="USB 2.0M DSC "
- SYSFS{rev}="1.00"
- SYSFS{online}="1"
-
- looking at the device chain at '/sys/devices/pci0000:00/0000:00:02.1/usb3/3-3':
- BUS="usb"
- ID="3-3"
- SYSFS{detach_state}="0"
- SYSFS{bNumInterfaces}=" 1"
- SYSFS{bConfigurationValue}="1"
- SYSFS{bmAttributes}="c0"
- SYSFS{bMaxPower}=" 0mA"
- SYSFS{idVendor}="052b"
- SYSFS{idProduct}="1514"
- SYSFS{bcdDevice}="0100"
- SYSFS{bDeviceClass}="00"
- SYSFS{bDeviceSubClass}="00"
- SYSFS{bDeviceProtocol}="00"
- SYSFS{bNumConfigurations}="1"
- SYSFS{speed}="12"
- SYSFS{manufacturer}="Tekom Technologies, Inc"
- SYSFS{product}="USB 2.0M DSC"
-
-
-The udevinfo tool provides a lot of information which you can simply copy-paste as udev rules. The reason that I have colour coded the above output is to point out that you generally cannot mix and match information from different parts of the udevinfo output. In the above output, I could not combine information from the different coloured sections - this is because each section of output refers to a different directory in SYSFS. For example, the following rule would not work:
-BUS="scsi", SYSFS{manufacturer}="Tekom Technologies, Inc", NAME="%k"+Here are some examples which incorporate the above patterns. Note the use of the string substitution operators. +
- -+ ++KERNEL=="fd[0-9]*", NAME="floppy/%n", SYMLINK+="%k" +KERNEL=="hiddev*", NAME="usb/%k" +
+The first rule matches all floppy disk drives, and ensures that the device nodes are placed in the /dev/floppy directory, as well as creating a symbolic link from the default name. The second rule ensures that hiddev devices are only present in the /dev/usb directory. +
+ ++The concept of using interesting information from sysfs was briefly touched upon above. In order to write rules based on this information, you first need to know the names of the attributes and their current values. +
+ ++sysfs is actually a very simple structure. It is logically divided into directories. Each directory contains a number of files (attributes) which typically contain just one value. Some symbolic links are present, which link various parts of the tree together. +
+ ++Some directories are referred to as top-level device paths. These directories act as the top-level glue which chain other parts of sysfs to the device in question. Top-level device paths can be classified as sysfs directories which contain a dev file, the following command will list these for you: +
+ ++ +# find /sys -name dev
+For example, on my system, the /sys/block/sda directory is the device path for my hard disk. It is chained to the controller through the /sys/block/sda/device/ symbolic link, which is in turn chained to the device driver through the /sys/block/sda/device/driver/ symbolic link. +
+ ++When you write rules based on sysfs information, you are simply matching attribute contents of some files in one part of the chain. For example, I can read the size of my hard disk as follows: +
-After plugging in my printer, I started looking around some /sys directories for a relevant place to start. I didn't get anywhere, but I noticed that my printer had been given device node /dev/lp0. I used this command sequence to find an answer:-Running "udevinfo -a -p /sys/class/usb/lp0" provided me with a heap of info, as usual. I picked out the relevant bits for unique device identification: +-# cd /sys -# find | grep lp0 -./class/usb/lp0 -./class/usb/lp0/dev -./class/usb/lp0/driver -./class/usb/lp0/device +# cat /sys/block/sda/size +234441648
+In a udev rule, I could use SYSFS{size}=="234441648" to identify this disk. As udev iterates through the entire device chain, I could alternatively opt to match attributes in another part of the chain (e.g. attributes in /sys/class/block/sda/device/), however there are some caveats when dealing with different parts of the chain which are described later. +
+ ++Although this serves as a useful introduction as to the structure of sysfs and exactly how udev matches values, manually trawling through sysfs is both time consuming and unnecessary. +
+ + ++Enter udevinfo, which is probably the most straightforward tool you can use to construct rules. All you need to know is the sysfs device path of the device in question. A trimmed example is shown below: +
+
-looking at the device chain at '/sys/devices/pci0000:00/0000:00:02.1/usb3/3-3':
-BUS="usb"
-SYSFS{manufacturer}="EPSON"
-SYSFS{product}="USB Printer"
-SYSFS{serial}="L72010011070626380"
+# udevinfo -a -p /sys/block/sda
+
+ looking at device '/block/sda':
+ KERNEL=="sda"
+ SUBSYSTEM=="block"
+ SYSFS{stat}==" 128535 2246 2788977 766188 73998 317300 3132216 5735004 0 516516 6503316"
+ SYSFS{size}=="234441648"
+ SYSFS{removable}=="0"
+ SYSFS{range}=="16"
+ SYSFS{dev}=="8:0"
+
+ looking at device '/devices/pci0000:00/0000:00:07.0/host0/target0:0:0/0:0:0:0':
+ ID=="0:0:0:0"
+ BUS=="scsi"
+ DRIVER=="sd"
+ SYSFS{ioerr_cnt}=="0x0"
+ SYSFS{iodone_cnt}=="0x31737"
+ SYSFS{iorequest_cnt}=="0x31737"
+ SYSFS{iocounterbits}=="32"
+ SYSFS{timeout}=="30"
+ SYSFS{state}=="running"
+ SYSFS{rev}=="3.42"
+ SYSFS{model}=="ST3120827AS "
+ SYSFS{vendor}=="ATA "
+ SYSFS{scsi_level}=="6"
+ SYSFS{type}=="0"
+ SYSFS{queue_type}=="none"
+ SYSFS{queue_depth}=="1"
+ SYSFS{device_blocked}=="0"
BUS="usb", SYSFS{serial}="L72010011070626380", NAME="%k", SYMLINK="epson_680"+As you can see, udevinfo simply produces a list of attributes you can use as-is as match keys in your udev rules. From the above example, I could produce (e.g.) either of the following two rules for this device: +
-And my printer nodes exist at /dev/lp0 (or /dev/lp1 if another printer was plugged in beforehand) and /dev/epson_680 always points at the device node for that particular printer.- -+SUBSYSTEM=="block", SYSFS{size}=="234441648", NAME="my_hard_disk" +BUS=="scsi", SYSFS{model}=="ST3120827AS", NAME="my_hard_disk"
+You may have noted the use of colour in the above examples. This is to demonstrate that you generally can not mix-and-match attributes from different sections of the udevinfo output - your rule will not work. For example, the following rule is invalid: +
+ ++ ++SUBSYSTEM=="block", SYSFS{size}=="234441648", SYSFS{model}=="ST3120827AS", NAME="my_hard_disk"
+You are usually provided with a large number of attributes, and you must pick a number of them (from the same section) to construct your rule. In general, you want to choose attributes which identify your device in a persistent and human-recognisable way. In the examples above, I chose the size of my disk and its model number. I did not use meaningless numbers such as SYSFS{iodone_cnt}=="0x31737". +
+ ++Another point to note is that it is common for text attributes to appear in the udevinfo output to be padded with spaces (e.g. see ST3120827AS above). In your rules, you can either specify the extra spaces, or you can cut them off as I have done. +
+ ++The only complication with using udevinfo is that you are required to know the top-level device path (/sys/block/sda in the example above). This is not always obvious. However, as you are generally writing rules for device nodes which already exist, you can use udevinfo to look up the device path for you: +
+ ++ + +# udevinfo -a -p $(udevinfo -q path -n /dev/sda)
+Although udevinfo is almost certainly the most straightforward way of listing the exact attributes you can build rules from, some users are happier with other tools. Utilities such as usbview display a similar set of information, most of which can be used in rules. +
+ ++udev allows you to use additional assignments in rules to control ownership and permission attributes on each device. +
+ ++The GROUP assignment allows you to define which Unix group should own the device node. Here is an example rule which defines that the video group will own the framebuffer devices: +
+ ++ +KERNEL=="fb[0-9]*", NAME="fb/%n", SYMLINK+="%k", GROUP="video"
+The OWNER key, perhaps less useful, allows you to define which Unix user should have ownership permissions on the device node. Assuming the slightly odd situation where you would want john to own your floppy devices, you could use: +
+ ++ +KERNEL=="fd[0-9]*", OWNER="john"
+udev defaults to creating nodes with Unix permissions of 0660 (read/write to owner and group). If you need to, you can override these defaults on certain devices using rules including the MODE assignment. As an example, the following rule defines that the inotify node shall be readable and writable to everyone: +
+ ++ + +KERNEL=="inotify", NAME="misc/%k", SYMLINK+="%k", MODE="0666"
+Under some circumstances, you may require more flexibility than standard udev rules can provide. In this case, you can ask udev to run a program and use the standard output from that program to provide device naming. +
+ ++To use this functionality, you simply specify the absolute path of the program to run (and any parameters) in the PROGRAM assignment, and you then use some variant of the %c substitution in the NAME/SYMLINK assignments. +
+ ++The following examples refer to a fictional program found at /bin/device_namer. device_namer takes one command line argument which is the kernel name for the device. Based upon this kernel name, device_namer does its magic and produces some output to the usual stdout pipe, split into several parts. Each part is just a single word, and parts are separated by a single space. +
-Quick Intro: My camera identifies itself as an external SCSI hard disk (it uses the usb-storage driver which is also used by devices such as USB hard disks and flash-card readers). I can then mount the partition on that disk and copy images over. Not all cameras work like this - many require external software (e.g. gphoto2) to be able to access photos.+In our first example, we assume that device_namer outputs a number of parts, each one to form a symbolic link (alternative name) for the device in question. +
-This one is a bit tricky. Two nodes are created by default when my camera is connected : /dev/sda and /dev/sda1. sda1 is the node that I would like as my /dev/camera, as that is what gets mounted. The problem is that there are only small details which can be used as udev rules to show the difference between sda and sda1.-As these nodes (sda, sda1) are treated as block devices, looking in /sys/block would be a good place to start.KERNEL=="hda", PROGRAM="/bin/device_namer %k", SYMLINK+="%c"
+The next example assumes that device_namer outputs two parts, the first being the device name, and the second being the name for an additional symbolic link. We now introduce the %c{N} substitution, which refers to part N of the output: +
-In my /sys/block, I have a directory named sda. In my /sys/block/sda, I have a directory named sda1. Both of these directories have dev files in, so they are OK for udev rules. Running the following dumps a lot of information about my camera and the USB ports it is connected through. +KERNEL=="hda", PROGRAM="/bin/device_namer %k", NAME="%c{1}", SYMLINK+="%c{2}"+The next example assumes that device_namer outputs one part for the device name, followed by any number of parts which will form additional symbolic links. We now introduce the %c{N+} substitution, which evaluates to part N, N+1, N+2, ... until the end of the output. +
+ +KERNEL=="hda", PROGRAM="/bin/device_namer %k", NAME="%c{1}", SYMLINK+="%c{2+}"+Output parts can be used in any assignment key, not only NAME and SYMLINK. The example below uses a fictional program to determine the Unix group which should own the device: +
+ ++ + +KERNEL=="hda", PROGRAM="/bin/who_owns_device %k", GROUP="%c"
+Yet another reason for writing udev rules is to run a particular program when a device is connected or disconnected. For example, you might want to execute a script to automatically download all of your photos from your digital camera when it is connected. +
+ ++Do not confuse this with the PROGRAM functionality described above. PROGRAM is used for running programs which produce device names (and they shouldn't do anything other than that). When those programs are being executed, the device node has not yet been created, so acting upon the device in any way is not possible. +
+ ++The functionality introduced here allows you to run a program after the device node is put in place. This program can act on the device, however it must not run for any extended period of time, because udev is effectively paused while these programs are running. One workaround for this limitation is to make sure your program immediately detaches itself. +
+ ++Here is an example rule which demonstrates the use of the RUN list assignment: +
+ ++ +KERNEL=="sdb", RUN+="/usr/bin/my_program"
+When /usr/bin/my_program is executed, various parts of the udev environment are available as environment variables, including key values such as SUBSYSTEM. You can also use the ACTION environment variable to detect whether the device is being connected or disconnected - ACTION will be either "add" or "remove" respectively. +
+ + ++udev provides an ENV key for environment variables which can be used for both matching and assignment. +
+ ++In the assignment case, you can set environment variables which you can then match against later. You can also set environment variables which can be used by any external programs invoked using the techniques mentioned above. A fictional example rule which sets an environment variable is shown below. +
+ +KERNEL=="fd0", SYMLINK+="floppy", ENV{some_var}="value"+In the matching case, you can ensure that rules only run depending on the value of an environment variable. Note that the environment that udev sees will not be the same user environment as you get on the console. A fictional rule involving an environment match is shown below. +
+ +KERNEL=="fd0", ENV{an_env_var}=="yes", SYMLINK+="floppy"+The above rule only creates the /dev/floppy link if $an_env_var is set to "yes" in udev's environment. +
+ + ++Another assignment which can prove useful is the OPTIONS list. A few options are available: +
+ ++For example, the rule below sets the group ownership on my hard disk node, and ensures that no later rule can have any effect: +
+ ++ + +KERNEL=="sda", GROUP="disk", OPTIONS+="last_rule"
+I power on my printer, and it is assigned device node /dev/lp0. Not satisfied with such a bland name, I decide to use udevinfo to aid me in writing a rule which will provide an alternative name: +
-# udevinfo -a -p /sys/block/sda
-# udevinfo -a -p /sys/block/sda/sda1
+# udevinfo -a -p $(udevinfo -q path -n /dev/lp0)
+looking at the device chain at '/sys/devices/pci0000:00/0000:00:02.1/usb3/3-3':
+BUS=="usb"
+SYSFS{manufacturer}=="EPSON"
+SYSFS{product}=="USB Printer"
+SYSFS{serial}=="L72010011070626380"
+My rule becomes: +
-To differentiate between sda and sda1, I decided that matching KERNEL names would be most appropriate here. Some examples of KERNEL names for this type of device are: sda, sda1, sdb, sdb1, sdc, ...BUS=="usb", SYSFS{serial}=="L72010011070626380", SYMLINK+="epson_680"SYSFS{product}="USB 2.0M DSC"+Like most, my camera identifies itself as an external hard disk connected over the USB bus, using the SCSI transport. To access my photos, I mount the drive and copy the image files onto my hard disk. +
-So that gives me my rule. For completeness, I also include a BUS key (this was also found in the udevinfo output). -BUS="usb", SYSFS{product}="USB 2.0M DSC", KERNEL="sd?1", NAME="%k", SYMLINK="camera"+Not all cameras work in this way: some of them use a non-storage protocol such as cameras supported by gphoto2. In the gphoto case, you do not want to be writing rules for your device, as is it controlled purely through userspace (rather than a specific kernel driver). +
-Now, when my camera is plugged in, it will be named /dev/sda1 (or, if sda1 isnt available, it might be called /dev/sdb1) and will always be correctly linked to from /dev/camera. The /dev/sda (or sdb) node still appears as normal, but the important thing is that my custom persistant "camera" symlink points to the mountable partition.+A common complication with USB camera devices is that they usually identify themselves as a disk with a single partition, in this case /dev/sdb with /dev/sdb1. The sdb node is useless to me, but sdb1 is interesting - this is the one I want to mount. There is a problem here that because sysfs is chained, the useful attributes which udevinfo produces for /dev/sdb1 are identical to the ones for /dev/sdb. This results in your rule potentially matching both the raw disk and the partition, which is not what you want, your rule should be specific. +
- -+To get around this, you simply need to think about what differs between sdb and sdb1. It is surprisingly simple: the name itself differs, so we can use a simple pattern match on the NAME field. +
-Carl Streeter, the owner of a large USB hard disk, wrote to me and explained that unlike in my digital camera example, the /dev/sda node is useful to him. He pointed out that he does occasionally need to use tools such as fdisk and hdparm on that node.
+# udevinfo -a -p $(udevinfo -q path -n /dev/sdb1)
+ looking at device '/devices/pci0000:00/0000:00:02.0/usb2/2-1/2-1:1.0/host6/target6:0:0/6:0:0:0':
+ ID=="6:0:0:0"
+ BUS=="scsi"
+ DRIVER=="sd"
+ SYSFS{rev}=="1.00"
+ SYSFS{model}=="X250,D560Z,C350Z"
+ SYSFS{vendor}=="OLYMPUS "
+ SYSFS{scsi_level}=="3"
+ SYSFS{type}=="0"
++My rule: +
+ +KERNEL=="sd?1", BUS=="scsi", SYSFS{model}=="X250,D560Z,C350Z", SYMLINK+="camera"+A USB hard disk is comparable to the USB camera I described above, however typical usage patterns are different. In the camera example, I explained that I am not interested in the sdb node - it's only real use is for partitioning (e.g. with fdisk), but why would I want to partition my camera!? +
-Carl's rule is: -BUS="usb", KERNEL="sd*", SYSFS{product}="USB 2.0 Storage Device", NAME="%k", SYMLINK="usbhd%n"+Of course, if you have a 100GB USB hard disk, it is perfectly understandable that you might want to partition it, in which case we can take advantage of udev's string substitutions: +
+BUS=="usb", KERNEL=="sd*", SYSFS{product}=="USB 2.0 Storage Device", NAME="%k", SYMLINK+="usbhd%n"This rule creates symlinks such as: -
+USB card readers (CompactFlash, SmartMedia, etc) are yet another range of USB storage devices which have different usage requirements. +
+ ++These devices typically do not inform the host computer upon media change. So, if you plug in the device with no media, and then insert a card, the computer does not realise, and you do not have your mountable sdb1 partition node for the media. +
+ ++One possible solution is to take advantage of the all_partitions option, which will create 16 partition nodes for every block device that the rule matches: +
+ +BUS=="usb", SYSFS{product}=="USB 2.0 CompactFlash Reader", SYMLINK+="cfrdr%n", OPTIONS+="all_partitions"+These devices work as USB-serial devices, so by default, you only get the ttyUSB1 device node. The palm utilities rely on /dev/pilot, so many users will want to use a rule to provide this. +
+ ++Carsten Clasohm's blog post appears to be the definitive source for this. Carsten's rule is shown below: +
+ +BUS=="usb", SYSFS{product}=="Palm Handheld", KERNEL=="ttyUSB*", SYMLINK+="pilot"+Note that the product string seems to vary from product to product, so make sure that you check (using udevinfo) which one applies to you. +
-+I have two optical drives in this computer: a DVD reader (hdc), and a DVD rewriter (hdd). I do not expect these device nodes to change, unless I physically rewire my system. However, many users like to have device nodes such as /dev/dvd for convenience. +
++As we know the KERNEL names for these devices, rule writing is simple. Here are some examples for my system: +
-You may have noticed that the default udev.rules file contains a rule which runs a script to produces names for block devices. Do not be confused by this - as usual, because your own rules in local.rules are processed before the default rules, the default rules will not be used when naming the hardware you have written rules for.-BUS="ide", KERNEL="hdc", NAME="%k", SYMLINK="dvd cdroms/cdrom%n" -BUS="ide", KERNEL="hdd", NAME="%k", SYMLINK="cdrw cdroms/cdrom%n" +BUS=="ide", KERNEL=="hdc", SYMLINK+="dvd", GROUP="cdrom" +BUS=="ide", KERNEL=="hdd", SYMLINK+="dvdrw", GROUP="cdrom"
+Even though they are referenced by names, network interfaces typically do not have device nodes associated with them. Despite that, the rule writing process is almost identical. +
-+It makes sense to simply match the MAC address of your interface in the rule, as this is unique. However, make sure that you use the exact MAC address as shown as udevinfo, because if you do not match the case exactly, your rule will not work. +
+ +
+# udevinfo -a -p /sys/class/net/eth0
+ looking at class device '/sys/class/net/eth0':
+ SYSFS{address}=="00:52:8b:d5:04:48"
++Here is my rule: +
+ +KERNEL=="eth*", SYSFS{address}=="00:52:8b:d5:04:48", NAME="lan"+You will need to reload the net driver for this rule to take effect. You can either unload and reload the module, or simply reboot the system. You will also need to reconfigure your system to use "lan" rather than "eth0". I had some troubles getting this going (the interface wasn't being renamed) until I had completely dropped all references to eth0. +After that, you should be able to use "lan" instead of "eth0" in any calls to ifconfig or similar utilities. +
-This section isn't really relevant to the purpose of this document, but judging from the hits I get from google, this is a hot topic. I will leave it here for now.+Assuming you are on a recent kernel with inotify support, udev will automatically monitor your rules directory and automatically pick up any modifications you make to the rule files. +
-This isn't all - you will also need to patch the nvidia kernel interface to export some basic info to SYSFS so that udev will create the devices. Martin Schlemmer has written a patch against the 1.0.5336 version of the nvidia drivers, which can be found here. The Gentoo package nvidia-kernel-1.0.5336-r1 contains this patch.+Despite this, udev will not automatically reprocess all devices and attempt to apply the new rule(s). For example, if you write a rule to add an extra symbolic link for your camera while your camera is plugged in, you cannot expect the extra symbolic link to show up right away. +
+ ++To make the symbolic link show up, you can either disconnect and reconnect your camera, or alternatively in the case of non-removable devices, you can run udevtrigger. +
+ ++If your kernel does not have inotify support, new rules will not be detected automatically. In this situation, you must run udevcontrol reload_rules after making any rule file modifications for those modifications to take effect. +
+ + ++If you know the top-level device path in sysfs, you can use udevtest to show the actions which udev would take. This may help you debug your rules. For example, assuming you want to debug a rule which acts on /sys/class/sound/dsp: +
-Another solution is to simply create the nvidia specific nodes on bootup. X will then load the module when required, and as the nodes are already in existance, you will not run into the problem described above. Place these commands in a file that is automatically executed on bootup (e.g. /etc/conf.d/local.start for Gentoo):-You should now be able to get into X with no problems.-mknod /dev/nvidia0 c 195 0 -mknod /dev/nvidiactl c 195 255 +# udevtest /class/sound/dsp +main: looking at device '/class/sound/dsp' from subsystem 'sound' +udev_rules_get_name: add symlink 'dsp' +udev_rules_get_name: rule applied, 'dsp' becomes 'sound/dsp' +udev_device_event: device '/class/sound/dsp' already known, remove possible symlinks +udev_node_add: creating device node '/dev/sound/dsp', major = '14', minor = '3', mode = '0660', uid = '0', gid = '18' +udev_node_add: creating symlink '/dev/dsp' to 'sound/dsp'
+Note the /sys prefix was removed from the udevtest command line argument, this is because udevtest operates on device paths. Also note that udevtest is purely a testing/debugging tool, it does not create any device nodes, despite what the output suggests! +
-+This document is written by Daniel Drake <dan@reactivated.net>. Feedback is appreciated. +
-+For support, you should mail the linux-hotplug mailing list: linux-hotplug-devel@lists.sourceforge.net. +
+ +
+Copyright (C) 2003-2006 Daniel Drake.
This document is licensed under the GNU General Public License, Version 2.
+