[info]
name = High detail
order = 2
-profile_file = ../../../lulzbot_profiles/TAZ6_single_v2.1/ABS_high-quality_mangrove_single-extruder_0.5noz_cura.ini
+profile_file = ../../../lulzbot_profiles/TAZ6_single_v2.1/ABS_high-quality_nutmeg_single-extruder_0.5noz_cura.ini
[info]
name = High speed
order = 1
-profile_file = ../../../lulzbot_profiles/TAZ6_single_v2.1/ABS_high-speed_mangrove_single-extruder_0.5noz_cura.ini
+profile_file = ../../../lulzbot_profiles/TAZ6_single_v2.1/ABS_high-speed_nutmeg_single-extruder_0.5noz_cura.ini
[info]
name = Standard
order = 0
-profile_file = ../../../lulzbot_profiles/TAZ6_single_v2.1/ABS_medium-quality_mangrove_single-extruder_0.5noz_cura.ini
+profile_file = ../../../lulzbot_profiles/TAZ6_single_v2.1/ABS_medium-quality_nutmeg_single-extruder_0.5noz_cura.ini
[info]
name = High detail
order = 2
-profile_file = ../../../lulzbot_profiles/TAZ6_single_v2.1/HIPS_high-quality_mangrove_single-extruder_0.5noz_cura.ini
+profile_file = ../../../lulzbot_profiles/TAZ6_single_v2.1/HIPS_high-quality_nutmeg_single-extruder_0.5noz_cura.ini
[info]
name = High speed
order = 1
-profile_file = ../../../lulzbot_profiles/TAZ6_single_v2.1/HIPS_high-speed_mangrove_single-extruder_0.5noz_cura.ini
+profile_file = ../../../lulzbot_profiles/TAZ6_single_v2.1/HIPS_high-speed_nutmeg_single-extruder_0.5noz_cura.ini
[info]
name = High detail
order = 2
-profile_file = ../../../lulzbot_profiles/TAZ6_single_v2.1/HIPS_high-quality_mangrove_single-extruder_0.5noz_cura.ini
+profile_file = ../../../lulzbot_profiles/TAZ6_single_v2.1/HIPS_high-quality_nutmeg_single-extruder_0.5noz_cura.ini
[info]
name = High speed
order = 1
-profile_file = ../../../lulzbot_profiles/TAZ6_single_v2.1/HIPS_high-speed_mangrove_single-extruder_0.5noz_cura.ini
+profile_file = ../../../lulzbot_profiles/TAZ6_single_v2.1/HIPS_high-speed_nutmeg_single-extruder_0.5noz_cura.ini
+++ /dev/null
-[info]
-name = High speed
-order = 1
-profile_file = ../../../lulzbot_profiles/TAZ6_single_v2.1/PC-ABS_high-speed_mangrove_single-extruder_0.5noz_cura.ini
+++ /dev/null
-[info]
-name = PC-ABS (Proto-pasta)
-material_types = Advanced
-order = 57
-description = Bed preparation required:
- Apply a PVA-based glue stick
- to bed surface before printing.
-url = lulzbot.com/store/filament/pc-abs-alloy?pk_campaign=software-cura
[info]
name = High detail
order = 2
-profile_file = ../../../lulzbot_profiles/TAZ6_single_v2.1/PLA_high-quality_mangrove_single-extruder_0.5noz_cura.ini
+profile_file = ../../../lulzbot_profiles/TAZ6_single_v2.1/PLA_high-quality_nutmeg_single-extruder_0.5noz_cura.ini
[info]
name = High speed
order = 1
-profile_file = ../../../lulzbot_profiles/TAZ6_single_v2.1/PLA_high-speed_mangrove_single-extruder_0.5noz_cura.ini
+profile_file = ../../../lulzbot_profiles/TAZ6_single_v2.1/PLA_high-speed_nutmeg_single-extruder_0.5noz_cura.ini
[info]
name = PLA (Village Plastics)
-material_types = Beginner
-order = 2
+material_types = Beginner|First Run
+order = 0
url = lulzbot.com/store/filament/pla-village?pk_campaign=software-cura
[info]
name = Standard
order = 0
-profile_file = ../../../lulzbot_profiles/TAZ6_single_v2.1/PLA_medium-quality_mangrove_single-extruder_0.5noz_cura.ini
+profile_file = ../../../lulzbot_profiles/TAZ6_single_v2.1/PLA_medium-quality_nutmeg_single-extruder_0.5noz_cura.ini
[info]
name = High detail
order = 2
-profile_file = ../../../lulzbot_profiles/TAZ6_single_v2.1/PLA_high-quality_mangrove_single-extruder_0.5noz_cura.ini
+profile_file = ../../../lulzbot_profiles/TAZ6_single_v2.1/PLA_high-quality_nutmeg_single-extruder_0.5noz_cura.ini
[info]
name = High speed
order = 1
-profile_file = ../../../lulzbot_profiles/TAZ6_single_v2.1/PLA_high-speed_mangrove_single-extruder_0.5noz_cura.ini
+profile_file = ../../../lulzbot_profiles/TAZ6_single_v2.1/PLA_high-speed_nutmeg_single-extruder_0.5noz_cura.ini
[info]
name = PLA (eSUN)
-material_types = Beginner|First Run
-order = 0
+material_types = Beginner
+order = 1
url = lulzbot.com/store/filament/pla-esun?pk_campaign=software-cura
[info]
name = Standard
order = 0
-profile_file = ../../../lulzbot_profiles/TAZ6_single_v2.1/PLA_medium-quality_mangrove_single-extruder_0.5noz_cura.ini
+profile_file = ../../../lulzbot_profiles/TAZ6_single_v2.1/PLA_medium-quality_nutmeg_single-extruder_0.5noz_cura.ini
perimeter_before_infill = True
nozzle_size = 0.5
print_speed = 50
-print_temperature = 250
+print_temperature = 240
print_temperature2 = 0
print_temperature3 = 0
print_temperature4 = 0
skirt_line_count = 1
skirt_gap = 3.0
skirt_minimal_length = 250
-fan_full_height = 0.5
-fan_speed = 40
-fan_speed_max = 60
+fan_full_height = 6
+fan_speed = 20
+fan_speed_max = 40
cool_min_feedrate = 10
cool_head_lift = False
solid_top = True
simplemodematerialtype = Beginner
[alterations]
-start.gcode = G21
+start.gcode = ;This profile is designed specifically for LulzBot Nutmeg 3D Printer
+ ;Basic slice data:
+ ;Sliced at: {day} {date} {time}
+ ;Layer height: {layer_height}
+ ;Walls: {wall_thickness}
+ ;Fill: {fill_density}
+ ;Estimated Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ G26 ; clear potential 'probe fail' condition
+ G21 ; set units to Millimetres
M107 ; disable fans
- G21 ; metric values
G90 ; absolute positioning
M82 ; set extruder to absolute mode
- M107 ; start with the fan off
G92 E0 ; set extruder position to 0
M140 S{print_bed_temperature}; get bed heating up
- G28 ; home all
- M109 S150 ; set to cleaning temp and wait
+ G28 XY ; home X and Y
+ G1 X-19 Y258 F1000 ; move to safe homing position
+ M109 S170 ; soften filament for z homing
+ G28 Z ; home Z
+ M104 S170 ; cool to probing temp during wipe
G1 E-30 F100 ; suck up XXmm of filament
- M109 S170 ; heat to probe temp
G1 X-15 Y100 F3000 ; move above wiper pad
- G1 Z2 ; Push nozzle into wiper
+ G1 Z1 ; push nozzle into wiper
G1 X-17 Y95 F1000 ; slow wipe
G1 X-17 Y90 F1000 ; slow wipe
G1 X-17 Y85 F1000 ; slow wipe
G1 X-15 Y25 Z1.5 F1000 ; slow wipe
G1 X-17 Y23 F1000 ; slow wipe
G1 Z10 ; raise extruder
- G1 Y10 ; move above probe
- M109 S170 ; set to probing temp
+ M109 S170 ; heat to probe temp
+ G1 X-11 Y-8 ; move above probe
M204 S100 ; set accel for probing
- G29 ; Probe
- M204 S700 ; set accel back to normal
+ G29 ; probe sequence (for auto-leveling)
+ M204 S500 ; set accel back to normal
G1 X0 Y0 Z15 F5000 ; get out the way
M400 ; clear buffer
G4 S1 ; pause
+ M117 Heating... ; LCD status message
+ M140 S{print_bed_temperature}; get bed heating up
M109 S{print_temperature} ; set extruder temp and wait
- G4 S25 ; wait for bed to temp up
+ M190 S{print_bed_temperature}; get bed temping up during first layer
G1 Z2 E0 F75 ; extrude filament back into nozzle
- M140 S{print_bed_temperature}; get bed temping up during first layer
- M117 Taz Printing... ; Message
-end.gcode = M400
+ M117 TAZ Printing... ; LCD status message
+end.gcode = ;
+ M400 ; wait for moves to finish
M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
M107 ; fans off
G91 ; relative positioning
G1 E-1 F300 ; retract the filament a bit before lifting the nozzle, to release some of the pressure
- G1 Z+0.5 E-5 X-20 Y-20 F3000 ; move Z up a bit and retract filament even more
+ G1 Z+20 E-5 X-20 Y-20 F3000 ; move Z up a bit and retract filament even more
+ M117 Cooling please wait ; progress indicator message
G90 ; absolute positioning
- G1 X0 Y250 ; move to cooling position
+ G1 Y0 F3000 ; move to cooling position
+ M190 S50 ; set bed to cool off
+ G1 Y280 F3000 ; present finished print
M84 ; steppers off
G90 ; absolute positioning
- M117 TAZ 6 Ready. ;{profile_string}
+ M117 Print complete ; progress indicator message
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
layer_height = 0.38
wall_thickness = 1.0
retraction_enable = True
-solid_layer_thickness = 1.04
-fill_density = 20
+solid_layer_thickness = 1
+fill_density = 40
perimeter_before_infill = True
nozzle_size = 0.5
print_speed = 50
-print_temperature = 250
+print_temperature = 240
print_temperature2 = 0
print_temperature3 = 0
print_temperature4 = 0
skirt_line_count = 1
skirt_gap = 3.0
skirt_minimal_length = 250
-fan_full_height = 0.5
-fan_speed = 40
-fan_speed_max = 60
+fan_full_height = 6
+fan_speed = 3
+fan_speed_max = 50
cool_min_feedrate = 10
cool_head_lift = False
solid_top = True
simplemodematerialtype = Beginner
[alterations]
-start.gcode = G21
+start.gcode = ;This profile is designed specifically for LulzBot Nutmeg 3D Printer
+ ;Basic slice data:
+ ;Sliced at: {day} {date} {time}
+ ;Layer height: {layer_height}
+ ;Walls: {wall_thickness}
+ ;Fill: {fill_density}
+ ;Estimated Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ G26 ; clear potential 'probe fail' condition
+ G21 ; set units to Millimetres
M107 ; disable fans
- G21 ; metric values
G90 ; absolute positioning
M82 ; set extruder to absolute mode
- M107 ; start with the fan off
G92 E0 ; set extruder position to 0
M140 S{print_bed_temperature}; get bed heating up
- G28 ; home all
- M109 S150 ; set to cleaning temp and wait
+ G28 XY ; home X and Y
+ G1 X-19 Y258 F1000 ; move to safe homing position
+ M109 S170 ; soften filament for z homing
+ G28 Z ; home Z
+ M104 S170 ; cool to probing temp during wipe
G1 E-30 F100 ; suck up XXmm of filament
- M109 S170 ; heat to probe temp
G1 X-15 Y100 F3000 ; move above wiper pad
- G1 Z2 ; Push nozzle into wiper
+ G1 Z1 ; push nozzle into wiper
G1 X-17 Y95 F1000 ; slow wipe
G1 X-17 Y90 F1000 ; slow wipe
G1 X-17 Y85 F1000 ; slow wipe
G1 X-15 Y25 Z1.5 F1000 ; slow wipe
G1 X-17 Y23 F1000 ; slow wipe
G1 Z10 ; raise extruder
- G1 Y10 ; move above probe
- M109 S170 ; set to probing temp
+ M109 S170 ; heat to probe temp
+ G1 X-11 Y-8 ; move above probe
M204 S100 ; set accel for probing
- G29 ; Probe
- M204 S700 ; set accel back to normal
+ G29 ; probe sequence (for auto-leveling)
+ M204 S500 ; set accel back to normal
G1 X0 Y0 Z15 F5000 ; get out the way
M400 ; clear buffer
G4 S1 ; pause
+ M117 Heating... ; LCD status message
+ M140 S{print_bed_temperature}; get bed heating up
M109 S{print_temperature} ; set extruder temp and wait
- G4 S25 ; wait for bed to temp up
+ M190 S{print_bed_temperature}; get bed temping up during first layer
G1 Z2 E0 F75 ; extrude filament back into nozzle
- M140 S{print_bed_temperature}; get bed temping up during first layer
- M117 Taz Printing... ; Message
-end.gcode = M400
+ M117 TAZ Printing... ; LCD status message
+end.gcode = ;
+ M400 ; wait for moves to finish
M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
M107 ; fans off
G91 ; relative positioning
G1 E-1 F300 ; retract the filament a bit before lifting the nozzle, to release some of the pressure
- G1 Z+0.5 E-5 X-20 Y-20 F3000 ; move Z up a bit and retract filament even more
+ G1 Z+20 E-5 X-20 Y-20 F3000 ; move Z up a bit and retract filament even more
+ M117 Cooling please wait ; progress indicator message
G90 ; absolute positioning
- G1 X0 Y250 ; move to cooling position
+ G1 Y0 F3000 ; move to cooling position
+ M190 S50 ; set bed to cool off
+ G1 Y280 F3000 ; present finished print
M84 ; steppers off
G90 ; absolute positioning
- M117 TAZ 6 Ready.
+ M117 Print complete ; progress indicator message
;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
skirt_line_count = 1
skirt_gap = 3.0
skirt_minimal_length = 250
-fan_full_height = 0.5
+fan_full_height = 6
fan_speed = 40
fan_speed_max = 60
cool_min_feedrate = 10
simplemodematerialtype = Beginner
[alterations]
-start.gcode = G21
+start.gcode = ;This profile is designed specifically for LulzBot Nutmeg 3D Printer
+ ;Basic slice data:
+ ;Sliced at: {day} {date} {time}
+ ;Layer height: {layer_height}
+ ;Walls: {wall_thickness}
+ ;Fill: {fill_density}
+ ;Estimated Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ G26 ; clear potential 'probe fail' condition
+ G21 ; set units to Millimetres
M107 ; disable fans
- G21 ; metric values
G90 ; absolute positioning
M82 ; set extruder to absolute mode
- M107 ; start with the fan off
G92 E0 ; set extruder position to 0
M140 S{print_bed_temperature}; get bed heating up
- G28 ; home all
- M109 S150 ; set to cleaning temp and wait
+ G28 XY ; home X and Y
+ G1 X-19 Y258 F1000 ; move to safe homing position
+ M109 S170 ; soften filament for z homing
+ G28 Z ; home Z
+ M104 S170 ; cool to probing temp during wipe
G1 E-30 F100 ; suck up XXmm of filament
- M109 S170 ; heat to probe temp
G1 X-15 Y100 F3000 ; move above wiper pad
- G1 Z2 ; Push nozzle into wiper
+ G1 Z1 ; push nozzle into wiper
G1 X-17 Y95 F1000 ; slow wipe
G1 X-17 Y90 F1000 ; slow wipe
G1 X-17 Y85 F1000 ; slow wipe
G1 X-15 Y25 Z1.5 F1000 ; slow wipe
G1 X-17 Y23 F1000 ; slow wipe
G1 Z10 ; raise extruder
- G1 Y10 ; move above probe
- M109 S170 ; set to probing temp
+ M109 S170 ; heat to probe temp
+ G1 X-11 Y-8 ; move above probe
M204 S100 ; set accel for probing
- G29 ; Probe
- M204 S700 ; set accel back to normal
+ G29 ; probe sequence (for auto-leveling)
+ M204 S500 ; set accel back to normal
G1 X0 Y0 Z15 F5000 ; get out the way
M400 ; clear buffer
G4 S1 ; pause
+ M117 Heating... ; LCD status message
+ M140 S{print_bed_temperature}; get bed heating up
M109 S{print_temperature} ; set extruder temp and wait
- G4 S25 ; wait for bed to temp up
+ M190 S{print_bed_temperature}; get bed temping up during first layer
G1 Z2 E0 F75 ; extrude filament back into nozzle
- M140 S{print_bed_temperature}; get bed temping up during first layer
- M117 Taz Printing... ; Message
-end.gcode = M400
+ M117 TAZ Printing... ; LCD status message
+end.gcode = ;
+ M400 ; wait for moves to finish
M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
M107 ; fans off
G91 ; relative positioning
G1 E-1 F300 ; retract the filament a bit before lifting the nozzle, to release some of the pressure
- G1 Z+0.5 E-5 X-20 Y-20 F3000 ; move Z up a bit and retract filament even more
+ G1 Z+20 E-5 X-20 Y-20 F3000 ; move Z up a bit and retract filament even more
+ M117 Cooling please wait ; progress indicator message
G90 ; absolute positioning
- G1 X0 Y250 ; move to cooling position
+ G1 Y0 F3000 ; move to cooling position
+ M190 S50 ; set bed to cool off
+ G1 Y280 F3000 ; present finished print
M84 ; steppers off
G90 ; absolute positioning
- M117 TAZ 6 Ready. ;{profile_string}
+ M117 Print complete ; progress indicator message
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
perimeter_before_infill = True
nozzle_size = 0.5
print_speed = 50
-print_temperature = 250
+print_temperature = 240
print_temperature2 = 0
print_temperature3 = 0
print_temperature4 = 0
solidarea_speed = 45
inset0_speed = 20
insetx_speed = 25
-cool_min_layer_time = 20
+cool_min_layer_time = 10
fan_enabled = True
skirt_line_count = 1
skirt_gap = 3.0
skirt_minimal_length = 250
-fan_full_height = 0.5
-fan_speed = 40
-fan_speed_max = 50
+fan_full_height = 6
+fan_speed = 20
+fan_speed_max = 40
cool_min_feedrate = 10
cool_head_lift = False
solid_top = True
simplemodematerialtype = Beginner
[alterations]
-start.gcode = G21
+start.gcode = ;This profile is designed specifically for LulzBot Nutmeg 3D Printer
+ ;Basic slice data:
+ ;Sliced at: {day} {date} {time}
+ ;Layer height: {layer_height}
+ ;Walls: {wall_thickness}
+ ;Fill: {fill_density}
+ ;Estimated Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ G26 ; clear potential 'probe fail' condition
+ G21 ; set units to Millimetres
M107 ; disable fans
- G21 ; metric values
G90 ; absolute positioning
M82 ; set extruder to absolute mode
- M107 ; start with the fan off
G92 E0 ; set extruder position to 0
M140 S{print_bed_temperature}; get bed heating up
- G28 ; home all
- M109 S150 ; set to cleaning temp and wait
+ G28 XY ; home X and Y
+ G1 X-19 Y258 F1000 ; move to safe homing position
+ M109 S170 ; soften filament for z homing
+ G28 Z ; home Z
+ M104 S170 ; cool to probing temp during wipe
G1 E-30 F100 ; suck up XXmm of filament
- M109 S170 ; heat to probe temp
G1 X-15 Y100 F3000 ; move above wiper pad
- G1 Z2 ; Push nozzle into wiper
+ G1 Z1 ; push nozzle into wiper
G1 X-17 Y95 F1000 ; slow wipe
G1 X-17 Y90 F1000 ; slow wipe
G1 X-17 Y85 F1000 ; slow wipe
G1 X-15 Y25 Z1.5 F1000 ; slow wipe
G1 X-17 Y23 F1000 ; slow wipe
G1 Z10 ; raise extruder
- G1 Y10 ; move above probe
- M109 S170 ; set to probing temp
+ M109 S170 ; heat to probe temp
+ G1 X-11 Y-8 ; move above probe
M204 S100 ; set accel for probing
- G29 ; Probe
- M204 S700 ; set accel back to normal
+ G29 ; probe sequence (for auto-leveling)
+ M204 S500 ; set accel back to normal
G1 X0 Y0 Z15 F5000 ; get out the way
M400 ; clear buffer
G4 S1 ; pause
+ M117 Heating... ; LCD status message
+ M140 S{print_bed_temperature}; get bed heating up
M109 S{print_temperature} ; set extruder temp and wait
- G4 S25 ; wait for bed to temp up
+ M190 S{print_bed_temperature}; get bed temping up during first layer
G1 Z2 E0 F75 ; extrude filament back into nozzle
- M140 S{print_bed_temperature}; get bed temping up during first layer
- M117 Taz Printing... ; Message
-end.gcode = M400
+ M117 TAZ Printing... ; LCD status message
+end.gcode = ;
+ M400 ; wait for moves to finish
M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
M107 ; fans off
G91 ; relative positioning
G1 E-1 F300 ; retract the filament a bit before lifting the nozzle, to release some of the pressure
- G1 Z+0.5 E-5 X-20 Y-20 F3000 ; move Z up a bit and retract filament even more
+ G1 Z+20 E-5 X-20 Y-20 F3000 ; move Z up a bit and retract filament even more
+ M117 Cooling please wait ; progress indicator message
G90 ; absolute positioning
- G1 X0 Y250 ; move to cooling position
+ G1 Y0 F3000 ; move to cooling position
+ M190 S50 ; set bed to cool off
+ G1 Y280 F3000 ; present finished print
M84 ; steppers off
G90 ; absolute positioning
- M117 TAZ 6 Ready. ;{profile_string}
+ M117 Print complete ; progress indicator message
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
perimeter_before_infill = True
nozzle_size = 0.5
print_speed = 50
-print_temperature = 250
+print_temperature = 240
print_temperature2 = 0
print_temperature3 = 0
print_temperature4 = 0
skirt_line_count = 1
skirt_gap = 3.0
skirt_minimal_length = 250
-fan_full_height = 0.5
+fan_full_height = 6
fan_speed = 40
fan_speed_max = 50
cool_min_feedrate = 10
simplemodematerialtype = Beginner
[alterations]
-start.gcode = G21
+start.gcode = ;This profile is designed specifically for LulzBot Nutmeg 3D Printer
+ ;Basic slice data:
+ ;Sliced at: {day} {date} {time}
+ ;Layer height: {layer_height}
+ ;Walls: {wall_thickness}
+ ;Fill: {fill_density}
+ ;Estimated Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ G26 ; clear potential 'probe fail' condition
+ G21 ; set units to Millimetres
M107 ; disable fans
- G21 ; metric values
G90 ; absolute positioning
M82 ; set extruder to absolute mode
- M107 ; start with the fan off
G92 E0 ; set extruder position to 0
M140 S{print_bed_temperature}; get bed heating up
- G28 ; home all
- M109 S150 ; set to cleaning temp and wait
+ G28 XY ; home X and Y
+ G1 X-19 Y258 F1000 ; move to safe homing position
+ M109 S170 ; soften filament for z homing
+ G28 Z ; home Z
+ M104 S170 ; cool to probing temp during wipe
G1 E-30 F100 ; suck up XXmm of filament
- M109 S170 ; heat to probe temp
G1 X-15 Y100 F3000 ; move above wiper pad
- G1 Z2 ; Push nozzle into wiper
+ G1 Z1 ; push nozzle into wiper
G1 X-17 Y95 F1000 ; slow wipe
G1 X-17 Y90 F1000 ; slow wipe
G1 X-17 Y85 F1000 ; slow wipe
G1 X-15 Y25 Z1.5 F1000 ; slow wipe
G1 X-17 Y23 F1000 ; slow wipe
G1 Z10 ; raise extruder
- G1 Y10 ; move above probe
- M109 S170 ; set to probing temp
+ M109 S170 ; heat to probe temp
+ G1 X-11 Y-8 ; move above probe
M204 S100 ; set accel for probing
- G29 ; Probe
- M204 S700 ; set accel back to normal
+ G29 ; probe sequence (for auto-leveling)
+ M204 S500 ; set accel back to normal
G1 X0 Y0 Z15 F5000 ; get out the way
M400 ; clear buffer
G4 S1 ; pause
+ M117 Heating... ; LCD status message
+ M140 S{print_bed_temperature}; get bed heating up
M109 S{print_temperature} ; set extruder temp and wait
- G4 S25 ; wait for bed to temp up
+ M190 S{print_bed_temperature}; get bed temping up during first layer
G1 Z2 E0 F75 ; extrude filament back into nozzle
- M140 S{print_bed_temperature}; get bed temping up during first layer
- M117 Taz Printing... ; Message
-end.gcode = M400
+ M117 TAZ Printing... ; LCD status message
+end.gcode = ;
+ M400 ; wait for moves to finish
M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
M107 ; fans off
G91 ; relative positioning
G1 E-1 F300 ; retract the filament a bit before lifting the nozzle, to release some of the pressure
- G1 Z+0.5 E-5 X-20 Y-20 F3000 ; move Z up a bit and retract filament even more
+ G1 Z+20 E-5 X-20 Y-20 F3000 ; move Z up a bit and retract filament even more
+ M117 Cooling please wait ; progress indicator message
G90 ; absolute positioning
- G1 X0 Y250 ; move to cooling position
+ G1 Y0 F3000 ; move to cooling position
+ M190 S50 ; set bed to cool off
+ G1 Y280 F3000 ; present finished print
M84 ; steppers off
G90 ; absolute positioning
- M117 TAZ 6 Ready. ;{profile_string}
+ M117 Print complete ; progress indicator message
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
perimeter_before_infill = True
nozzle_size = 0.5
print_speed = 50
-print_temperature = 250
+print_temperature = 240
print_temperature2 = 0
print_temperature3 = 0
print_temperature4 = 0
solidarea_speed = 45
inset0_speed = 30
insetx_speed = 35
-cool_min_layer_time = 20
+cool_min_layer_time = 15
fan_enabled = True
skirt_line_count = 1
skirt_gap = 3.0
skirt_minimal_length = 250
-fan_full_height = 0.5
-fan_speed = 40
-fan_speed_max = 50
+fan_full_height = 6
+fan_speed = 20
+fan_speed_max = 40
cool_min_feedrate = 10
cool_head_lift = False
solid_top = True
simplemodematerialtype = Beginner
[alterations]
-start.gcode = G21
+start.gcode = ;This profile is designed specifically for LulzBot Nutmeg 3D Printer
+ ;Basic slice data:
+ ;Sliced at: {day} {date} {time}
+ ;Layer height: {layer_height}
+ ;Walls: {wall_thickness}
+ ;Fill: {fill_density}
+ ;Estimated Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ G26 ; clear potential 'probe fail' condition
+ G21 ; set units to Millimetres
M107 ; disable fans
- G21 ; metric values
G90 ; absolute positioning
M82 ; set extruder to absolute mode
- M107 ; start with the fan off
G92 E0 ; set extruder position to 0
M140 S{print_bed_temperature}; get bed heating up
- G28 ; home all
- M109 S150 ; set to cleaning temp and wait
+ G28 XY ; home X and Y
+ G1 X-19 Y258 F1000 ; move to safe homing position
+ M109 S170 ; soften filament for z homing
+ G28 Z ; home Z
+ M104 S170 ; cool to probing temp during wipe
G1 E-30 F100 ; suck up XXmm of filament
- M109 S170 ; heat to probe temp
G1 X-15 Y100 F3000 ; move above wiper pad
- G1 Z2 ; Push nozzle into wiper
+ G1 Z1 ; push nozzle into wiper
G1 X-17 Y95 F1000 ; slow wipe
G1 X-17 Y90 F1000 ; slow wipe
G1 X-17 Y85 F1000 ; slow wipe
G1 X-15 Y25 Z1.5 F1000 ; slow wipe
G1 X-17 Y23 F1000 ; slow wipe
G1 Z10 ; raise extruder
- G1 Y10 ; move above probe
- M109 S170 ; set to probing temp
+ M109 S170 ; heat to probe temp
+ G1 X-11 Y-8 ; move above probe
M204 S100 ; set accel for probing
- G29 ; Probe
- M204 S700 ; set accel back to normal
+ G29 ; probe sequence (for auto-leveling)
+ M204 S500 ; set accel back to normal
G1 X0 Y0 Z15 F5000 ; get out the way
M400 ; clear buffer
G4 S1 ; pause
+ M117 Heating... ; LCD status message
+ M140 S{print_bed_temperature}; get bed heating up
M109 S{print_temperature} ; set extruder temp and wait
- G4 S25 ; wait for bed to temp up
+ M190 S{print_bed_temperature}; get bed temping up during first layer
G1 Z2 E0 F75 ; extrude filament back into nozzle
- M140 S{print_bed_temperature}; get bed temping up during first layer
- M117 Taz Printing... ; Message
-end.gcode = M400
+ M117 TAZ Printing... ; LCD status message
+end.gcode = ;
+ M400 ; wait for moves to finish
M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
M107 ; fans off
G91 ; relative positioning
G1 E-1 F300 ; retract the filament a bit before lifting the nozzle, to release some of the pressure
- G1 Z+0.5 E-5 X-20 Y-20 F3000 ; move Z up a bit and retract filament even more
+ G1 Z+20 E-5 X-20 Y-20 F3000 ; move Z up a bit and retract filament even more
+ M117 Cooling please wait ; progress indicator message
G90 ; absolute positioning
- G1 X0 Y250 ; move to cooling position
+ G1 Y0 F3000 ; move to cooling position
+ M190 S50 ; set bed to cool off
+ G1 Y280 F3000 ; present finished print
M84 ; steppers off
G90 ; absolute positioning
- M117 TAZ 6 Ready. ;{profile_string}
+ M117 Print complete ; progress indicator message
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
+++ /dev/null
-[profile]
-layer_height = 0.38
-wall_thickness = 1.0
-retraction_enable = True
-solid_layer_thickness = 1.04
-fill_density = 20
-perimeter_before_infill = True
-nozzle_size = 0.5
-print_speed = 50
-print_temperature = 270
-print_temperature2 = 0
-print_temperature3 = 0
-print_temperature4 = 0
-print_temperature5 = 0
-print_bed_temperature = 115
-support = None
-platform_adhesion = None
-support_dual_extrusion = Both
-wipe_tower = False
-wipe_tower_volume = 15
-ooze_shield = False
-filament_diameter = 2.85
-filament_diameter2 = 0
-filament_diameter3 = 0
-filament_diameter4 = 0
-filament_diameter5 = 0
-filament_flow = 100.0
-retraction_speed = 10
-retraction_amount = 1
-retraction_dual_amount = 16.5
-retraction_min_travel = 1.5
-retraction_combing = All
-retraction_minimal_extrusion = 0.005
-retraction_hop = 0.1
-bottom_thickness = 0.425
-layer0_width_factor = 125
-object_sink = 0.0
-overlap_dual = 0.15
-travel_speed = 175
-bottom_layer_speed = 15
-infill_speed = 55
-solidarea_speed = 45
-inset0_speed = 45
-insetx_speed = 50
-cool_min_layer_time = 15
-fan_enabled = True
-skirt_line_count = 1
-skirt_gap = 3.0
-skirt_minimal_length = 250
-fan_full_height = 0.5
-fan_speed = 40
-fan_speed_max = 60
-cool_min_feedrate = 10
-cool_head_lift = False
-solid_top = True
-solid_bottom = True
-fill_overlap = 15
-support_type = Lines
-support_angle = 45
-support_fill_rate = 30
-support_xy_distance = 0.7
-support_z_distance = 0.05
-spiralize = False
-simple_mode = False
-brim_line_count = 10
-raft_margin = 5.0
-raft_line_spacing = 3.0
-raft_base_thickness = 0.3
-raft_base_linewidth = 1.0
-raft_interface_thickness = 0.27
-raft_interface_linewidth = 0.4
-raft_airgap_all = 0.0
-raft_airgap = 0.5
-raft_surface_layers = 2
-raft_surface_thickness = 0.27
-raft_surface_linewidth = 0.4
-fix_horrible_union_all_type_a = True
-fix_horrible_union_all_type_b = False
-fix_horrible_use_open_bits = False
-fix_horrible_extensive_stitching = False
-plugin_config = (lp1
- .
-object_center_x = -1
-object_center_y = -1
-simplemodesettings =
-simplemodeprofile = 2_normal
-simplemodematerial = 1_pla
-simplemodematerialtype = Beginner
-
-[alterations]
-start.gcode = G21
- M107 ; disable fans
- G21 ; metric values
- G90 ; absolute positioning
- M82 ; set extruder to absolute mode
- M107 ; start with the fan off
- G92 E0 ; set extruder position to 0
- M140 S{print_bed_temperature}; get bed heating up
- G28 ; home all
- M109 S150 ; set to cleaning temp and wait
- G1 E-30 F100 ; suck up XXmm of filament
- M109 S170 ; heat to probe temp
- G1 X-15 Y100 F3000 ; move above wiper pad
- G1 Z2 ; Push nozzle into wiper
- G1 X-17 Y95 F1000 ; slow wipe
- G1 X-17 Y90 F1000 ; slow wipe
- G1 X-17 Y85 F1000 ; slow wipe
- G1 X-15 Y90 F1000 ; slow wipe
- G1 X-17 Y80 F1000 ; slow wipe
- G1 X-15 Y95 F1000 ; slow wipe
- G1 X-17 Y75 F2000 ; fast wipe
- G1 X-15 Y65 F2000 ; fast wipe
- G1 X-17 Y70 F2000 ; fast wipe
- G1 X-15 Y60 F2000 ; fast wipe
- G1 X-17 Y55 F2000 ; fast wipe
- G1 X-15 Y50 F2000 ; fast wipe
- G1 X-17 Y40 F2000 ; fast wipe
- G1 X-15 Y45 F2000 ; fast wipe
- G1 X-17 Y35 F2000 ; fast wipe
- G1 X-15 Y40 F2000 ; fast wipe
- G1 X-17 Y70 F2000 ; fast wipe
- G1 X-15 Y30 Z2 F2000 ; fast wipe
- G1 X-17 Y35 F2000 ; fast wipe
- G1 X-15 Y25 F2000 ; fast wipe
- G1 X-17 Y30 F2000 ; fast wipe
- G1 X-15 Y25 Z1.5 F1000 ; slow wipe
- G1 X-17 Y23 F1000 ; slow wipe
- G1 Z10 ; raise extruder
- G1 Y10 ; move above probe
- M109 S170 ; set to probing temp
- M204 S100 ; set accel for probing
- G29 ; Probe
- M204 S700 ; set accel back to normal
- G1 X0 Y0 Z15 F5000 ; get out the way
- M400 ; clear buffer
- G4 S1 ; pause
- M109 S{print_temperature} ; set extruder temp and wait
- G4 S25 ; wait for bed to temp up
- G1 Z2 E0 F75 ; extrude filament back into nozzle
- M140 S{print_bed_temperature}; get bed temping up during first layer
- M117 Taz Printing... ; Message
-end.gcode = M400
- M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G91 ; relative positioning
- G1 E-1 F300 ; retract the filament a bit before lifting the nozzle, to release some of the pressure
- G1 Z+0.5 E-5 X-20 Y-20 F3000 ; move Z up a bit and retract filament even more
- G90 ; absolute positioning
- G1 X0 Y250 ; move to cooling position
- M84 ; steppers off
- G90 ; absolute positioning
- M117 TAZ 6 Ready.
- ;{profile_string}
-start2.gcode = ;Sliced at: {day} {date} {time}
- ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
- ;Print time: {print_time}
- ;Filament used: {filament_amount}m {filament_weight}g
- ;Filament cost: {filament_cost}
- ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
- ;M104 S{print_temperature} ;Uncomment to add your own temperature line
- ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
- ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
- G21 ;metric values
- G90 ;absolute positioning
- M107 ;start with the fan off
- G28 X0 Y0 ;move X/Y to min endstops
- G28 Z0 ;move Z to min endstops
- G1 Z15.0 F{travel_speed} ;move the platform down 15mm
- T1 ;Switch to the 2nd extruder
- G92 E0 ;zero the extruded length
- G1 F200 E10 ;extrude 10mm of feed stock
- G92 E0 ;zero the extruded length again
- G1 F200 E-{retraction_dual_amount}
- T0 ;Switch to the first extruder
- G92 E0 ;zero the extruded length
- G1 F200 E10 ;extrude 10mm of feed stock
- G92 E0 ;zero the extruded length again
- G1 F{travel_speed}
- ;Put printing message on LCD screen
- M117 Printing...
-end2.gcode = ;End GCode
- M104 T0 S0 ;extruder heater off
- M104 T1 S0 ;extruder heater off
- M140 S0 ;heated bed heater off (if you have it)
- G91 ;relative positioning
- G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
- G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
- G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
- M84 ;steppers off
- G90 ;absolute positioning
- ;{profile_string}
-start3.gcode = ;Sliced at: {day} {date} {time}
- ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
- ;Print time: {print_time}
- ;Filament used: {filament_amount}m {filament_weight}g
- ;Filament cost: {filament_cost}
- ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
- ;M104 S{print_temperature} ;Uncomment to add your own temperature line
- ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
- ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
- G21 ;metric values
- G90 ;absolute positioning
- M107 ;start with the fan off
- G28 X0 Y0 ;move X/Y to min endstops
- G28 Z0 ;move Z to min endstops
- G1 Z15.0 F{travel_speed} ;move the platform down 15mm
- T2 ;Switch to the 2nd extruder
- G92 E0 ;zero the extruded length
- G1 F200 E10 ;extrude 10mm of feed stock
- G92 E0 ;zero the extruded length again
- G1 F200 E-{retraction_dual_amount}
- T1 ;Switch to the 2nd extruder
- G92 E0 ;zero the extruded length
- G1 F200 E10 ;extrude 10mm of feed stock
- G92 E0 ;zero the extruded length again
- G1 F200 E-{retraction_dual_amount}
- T0 ;Switch to the first extruder
- G92 E0 ;zero the extruded length
- G1 F200 E10 ;extrude 10mm of feed stock
- G92 E0 ;zero the extruded length again
- G1 F{travel_speed}
- ;Put printing message on LCD screen
- M117 Printing...
-end3.gcode = ;End GCode
- M104 T0 S0 ;extruder heater off
- M104 T1 S0 ;extruder heater off
- M104 T2 S0 ;extruder heater off
- M140 S0 ;heated bed heater off (if you have it)
- G91 ;relative positioning
- G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
- G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
- G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
- M84 ;steppers off
- G90 ;absolute positioning
- ;{profile_string}
-start4.gcode = ;Sliced at: {day} {date} {time}
- ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
- ;Print time: {print_time}
- ;Filament used: {filament_amount}m {filament_weight}g
- ;Filament cost: {filament_cost}
- ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
- ;M104 S{print_temperature} ;Uncomment to add your own temperature line
- ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
- ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
- ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
- G21 ;metric values
- G90 ;absolute positioning
- M107 ;start with the fan off
- G28 X0 Y0 ;move X/Y to min endstops
- G28 Z0 ;move Z to min endstops
- G1 Z15.0 F{travel_speed} ;move the platform down 15mm
- T3 ;Switch to the 4th extruder
- G92 E0 ;zero the extruded length
- G1 F200 E10 ;extrude 10mm of feed stock
- G92 E0 ;zero the extruded length again
- G1 F200 E-{retraction_dual_amount}
- T2 ;Switch to the 3th extruder
- G92 E0 ;zero the extruded length
- G1 F200 E10 ;extrude 10mm of feed stock
- G92 E0 ;zero the extruded length again
- G1 F200 E-{retraction_dual_amount}
- T1 ;Switch to the 2nd extruder
- G92 E0 ;zero the extruded length
- G1 F200 E10 ;extrude 10mm of feed stock
- G92 E0 ;zero the extruded length again
- G1 F200 E-{retraction_dual_amount}
- T0 ;Switch to the first extruder
- G92 E0 ;zero the extruded length
- G1 F200 E10 ;extrude 10mm of feed stock
- G92 E0 ;zero the extruded length again
- G1 F{travel_speed}
- ;Put printing message on LCD screen
- M117 Printing...
-end4.gcode = ;End GCode
- M104 T0 S0 ;extruder heater off
- M104 T1 S0 ;extruder heater off
- M104 T2 S0 ;extruder heater off
- M104 T3 S0 ;extruder heater off
- M140 S0 ;heated bed heater off (if you have it)
- G91 ;relative positioning
- G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
- G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
- G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
- M84 ;steppers off
- G90 ;absolute positioning
- ;{profile_string}
-support_start.gcode =
-support_end.gcode =
-cool_start.gcode =
-cool_end.gcode =
-replace.csv =
-preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
- ;This code is added before the T(n)
-postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
- ;This code is added after the T(n)
-
skirt_line_count = 1
skirt_gap = 3.0
skirt_minimal_length = 250
-fan_full_height = 0.5
-fan_speed = 75
+fan_full_height = 6
+fan_speed = 80
fan_speed_max = 100
cool_min_feedrate = 10
cool_head_lift = False
simplemodematerialtype = Beginner
[alterations]
-start.gcode = G21
+start.gcode = ;This profile is designed specifically for LulzBot Nutmeg 3D Printer
+ ;Basic slice data:
+ ;Sliced at: {day} {date} {time}
+ ;Layer height: {layer_height}
+ ;Walls: {wall_thickness}
+ ;Fill: {fill_density}
+ ;Estimated Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ G26 ; clear potential 'probe fail' condition
+ G21 ; set units to Millimetres
M107 ; disable fans
- G21 ; metric values
G90 ; absolute positioning
M82 ; set extruder to absolute mode
- M107 ; start with the fan off
G92 E0 ; set extruder position to 0
M140 S{print_bed_temperature}; get bed heating up
- G28 ; home all
- M109 S130 ; set to cleaning temp and wait
+ G28 XY ; home X and Y
+ G1 X-19 Y258 F1000 ; move to safe homing position
+ M109 S170 ; soften filament for z homing
+ G28 Z ; home Z
+ M104 S170 ; cool to probing temp during wipe
G1 E-30 F100 ; suck up XXmm of filament
- M109 S140 ; heat to probe temp
G1 X-15 Y100 F3000 ; move above wiper pad
- G1 Z2 ; Push nozzle into wiper
+ G1 Z1 ; push nozzle into wiper
G1 X-17 Y95 F1000 ; slow wipe
G1 X-17 Y90 F1000 ; slow wipe
G1 X-17 Y85 F1000 ; slow wipe
G1 X-15 Y25 Z1.5 F1000 ; slow wipe
G1 X-17 Y23 F1000 ; slow wipe
G1 Z10 ; raise extruder
- G1 Y10 ; move above probe
- M109 S170 ; set to probing temp
+ M109 S150 ; heat to probe temp
+ G1 X-11 Y-8 ; move above probe
M204 S100 ; set accel for probing
- G29 ; Probe
- M204 S700 ; set accel back to normal
+ G29 ; probe sequence (for auto-leveling)
+ M204 S500 ; set accel back to normal
G1 X0 Y0 Z15 F5000 ; get out the way
M400 ; clear buffer
G4 S1 ; pause
+ M117 Heating... ; LCD status message
+ M140 S{print_bed_temperature}; get bed heating up
M109 S{print_temperature} ; set extruder temp and wait
- G4 S25 ; wait for bed to temp up
+ M190 S{print_bed_temperature}; get bed temping up during first layer
G1 Z2 E0 F75 ; extrude filament back into nozzle
- M140 S{print_bed_temperature}; get bed temping up during first layer
- M117 Taz Printing... ; Message
-end.gcode = M400
+ M117 TAZ Printing... ; LCD status message
+end.gcode = ;
+ M400 ; wait for moves to finish
M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
M107 ; fans off
G91 ; relative positioning
G1 E-1 F300 ; retract the filament a bit before lifting the nozzle, to release some of the pressure
- G1 Z+0.5 E-5 X-20 Y-20 F3000 ; move Z up a bit and retract filament even more
+ G1 Z+20 E-5 X-20 Y-20 F3000 ; move Z up a bit and retract filament even more
+ M117 Cooling please wait ; progress indicator message
G90 ; absolute positioning
- G1 X0 Y250 ; move to cooling position
+ G1 Y0 F3000 ; move to cooling position
+ M190 S50 ; set bed to cool off
+ G1 Y280 F3000 ; present finished print
M84 ; steppers off
G90 ; absolute positioning
- M117 TAZ 6 Ready. ;{profile_string}
+ M117 Print complete ; progress indicator message
+ ;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
[profile]
-layer_height = 0.22
+layer_height = 0.38
wall_thickness = 1.0
retraction_enable = True
solid_layer_thickness = 0.88
skirt_line_count = 1
skirt_gap = 3.0
skirt_minimal_length = 250
-fan_full_height = 0.5
-fan_speed = 60
+fan_full_height = 6
+fan_speed = 80
fan_speed_max = 100
cool_min_feedrate = 10
cool_head_lift = False
simplemodematerialtype = Beginner
[alterations]
-start.gcode = G21
+start.gcode = ;This profile is designed specifically for LulzBot Nutmeg 3D Printer
+ ;Basic slice data:
+ ;Sliced at: {day} {date} {time}
+ ;Layer height: {layer_height}
+ ;Walls: {wall_thickness}
+ ;Fill: {fill_density}
+ ;Estimated Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ G26 ; clear potential 'probe fail' condition
+ G21 ; set units to Millimetres
M107 ; disable fans
- G21 ; metric values
G90 ; absolute positioning
M82 ; set extruder to absolute mode
- M107 ; start with the fan off
G92 E0 ; set extruder position to 0
M140 S{print_bed_temperature}; get bed heating up
- G28 ; home all
- M109 S130 ; set to cleaning temp and wait
+ G28 XY ; home X and Y
+ G1 X-19 Y258 F1000 ; move to safe homing position
+ M109 S170 ; soften filament for z homing
+ G28 Z ; home Z
+ M104 S170 ; cool to probing temp during wipe
G1 E-30 F100 ; suck up XXmm of filament
G1 X-15 Y100 F3000 ; move above wiper pad
- G1 Z2 ; Push nozzle into wiper
+ G1 Z1 ; push nozzle into wiper
G1 X-17 Y95 F1000 ; slow wipe
G1 X-17 Y90 F1000 ; slow wipe
G1 X-17 Y85 F1000 ; slow wipe
G1 X-17 Y30 F2000 ; fast wipe
G1 X-15 Y25 Z1.5 F1000 ; slow wipe
G1 X-17 Y23 F1000 ; slow wipe
- M109 S140 ; heat to probe temp
G1 Z10 ; raise extruder
+ M109 S150 ; heat to probe temp
G1 X-11 Y-8 ; move above probe
M204 S100 ; set accel for probing
- G29 ; Probe
- M204 S700 ; set accel back to normal
+ G29 ; probe sequence (for auto-leveling)
+ M204 S500 ; set accel back to normal
G1 X0 Y0 Z15 F5000 ; get out the way
M400 ; clear buffer
G4 S1 ; pause
+ M117 Heating... ; LCD status message
+ M140 S{print_bed_temperature}; get bed heating up
M109 S{print_temperature} ; set extruder temp and wait
- G4 S25 ; wait for bed to temp up
+ M190 S{print_bed_temperature}; get bed temping up during first layer
G1 Z2 E0 F75 ; extrude filament back into nozzle
- M140 S{print_bed_temperature}; get bed temping up during first layer
- M117 Taz Printing... ; Message
-end.gcode = M400
+ M117 TAZ Printing... ; LCD status message
+end.gcode = ;
+ M400 ; wait for moves to finish
M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
M107 ; fans off
G91 ; relative positioning
G1 E-1 F300 ; retract the filament a bit before lifting the nozzle, to release some of the pressure
- G1 Z+0.5 E-5 X-20 Y-20 F3000 ; move Z up a bit and retract filament even more
+ G1 Z+20 E-5 X-20 Y-20 F3000 ; move Z up a bit and retract filament even more
+ M117 Cooling please wait ; progress indicator message
G90 ; absolute positioning
- G1 X0 Y250 ; move to cooling position
+ G1 Y0 F3000 ; move to cooling position
+ M190 S50 ; set bed to cool off
+ G1 Y280 F3000 ; present finished print
M84 ; steppers off
G90 ; absolute positioning
- M117 TAZ 6 Ready.
+ M117 Print complete ; progress indicator message
;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
[profile]
-layer_height = 0.38
+layer_height = 0.25
wall_thickness = 1.0
retraction_enable = True
-solid_layer_thickness = 0.88
+solid_layer_thickness = 0.75
fill_density = 20
perimeter_before_infill = True
nozzle_size = 0.5
overlap_dual = 0.15
travel_speed = 175
bottom_layer_speed = 15
-infill_speed = 55
-solidarea_speed = 45
-inset0_speed = 45
-insetx_speed = 50
-cool_min_layer_time = 15
+infill_speed = 50
+solidarea_speed = 40
+inset0_speed = 40
+insetx_speed = 45
+cool_min_layer_time = 10
fan_enabled = True
skirt_line_count = 1
skirt_gap = 3.0
skirt_minimal_length = 250
-fan_full_height = 0.5
-fan_speed = 40
-fan_speed_max = 60
+fan_full_height = 6
+fan_speed = 80
+fan_speed_max = 100
cool_min_feedrate = 10
cool_head_lift = False
solid_top = True
simplemodematerialtype = Beginner
[alterations]
-start.gcode = G21
+start.gcode = ;This profile is designed specifically for LulzBot Nutmeg 3D Printer
+ ;Basic slice data:
+ ;Sliced at: {day} {date} {time}
+ ;Layer height: {layer_height}
+ ;Walls: {wall_thickness}
+ ;Fill: {fill_density}
+ ;Estimated Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ G26 ; clear potential 'probe fail' condition
+ G21 ; set units to Millimetres
M107 ; disable fans
- G21 ; metric values
G90 ; absolute positioning
M82 ; set extruder to absolute mode
- M107 ; start with the fan off
G92 E0 ; set extruder position to 0
M140 S{print_bed_temperature}; get bed heating up
- G28 ; home all
- M109 S130 ; set to cleaning temp and wait
+ G28 XY ; home X and Y
+ G1 X-19 Y258 F1000 ; move to safe homing position
+ M109 S170 ; soften filament for z homing
+ G28 Z ; home Z
+ M104 S170 ; cool to probing temp during wipe
G1 E-30 F100 ; suck up XXmm of filament
- M109 S140 ; heat to probe temp
G1 X-15 Y100 F3000 ; move above wiper pad
- G1 Z2 ; Push nozzle into wiper
+ G1 Z1 ; push nozzle into wiper
G1 X-17 Y95 F1000 ; slow wipe
G1 X-17 Y90 F1000 ; slow wipe
G1 X-17 Y85 F1000 ; slow wipe
G1 X-15 Y25 Z1.5 F1000 ; slow wipe
G1 X-17 Y23 F1000 ; slow wipe
G1 Z10 ; raise extruder
- G1 Y10 ; move above probe
- M109 S170 ; set to probing temp
+ M109 S150 ; heat to probe temp
+ G1 X-11 Y-8 ; move above probe
M204 S100 ; set accel for probing
- G29 ; Probe
- M204 S700 ; set accel back to normal
+ G29 ; probe sequence (for auto-leveling)
+ M204 S500 ; set accel back to normal
G1 X0 Y0 Z15 F5000 ; get out the way
M400 ; clear buffer
G4 S1 ; pause
+ M117 Heating... ; LCD status message
+ M140 S{print_bed_temperature}; get bed heating up
M109 S{print_temperature} ; set extruder temp and wait
- G4 S25 ; wait for bed to temp up
+ M190 S{print_bed_temperature}; get bed temping up during first layer
G1 Z2 E0 F75 ; extrude filament back into nozzle
- M140 S{print_bed_temperature}; get bed temping up during first layer
- M117 Taz Printing... ; Message
-end.gcode = M400
+ M117 TAZ Printing... ; LCD status message
+end.gcode = ;
+ M400 ; wait for moves to finish
M104 S0 ; hotend off
- M140 S0 ; heated bed heater off (if you have it)
M107 ; fans off
G91 ; relative positioning
G1 E-1 F300 ; retract the filament a bit before lifting the nozzle, to release some of the pressure
- G1 Z+0.5 E-5 X-20 Y-20 F3000 ; move Z up a bit and retract filament even more
+ G1 Z+20 E-5 X-20 Y-20 F3000 ; move Z up a bit and retract filament even more
+ M117 Cooling please wait ; progress indicator message
G90 ; absolute positioning
- G1 X0 Y250 ; move to cooling position
+ G1 Y0 F3000 ; move to cooling position
+ M190 S50 ; set bed to cool off
+ G1 Y280 F3000 ; present finished print
M84 ; steppers off
G90 ; absolute positioning
- M117 TAZ 6 Ready.
+ M117 Print complete ; progress indicator message
;{profile_string}
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
if ((material == "HIPS_eSUN" and machine_type.startswith("lulzbot_mini")) or \
(material == "ABS_VP" and machine_type.startswith("lulzbot_TAZ_4")) or \
(material == "ABS_VP" and machine_type.startswith("lulzbot_TAZ_5")) or \
- (material == "PLA_eSUN" and machine_type.startswith("lulzbot_TAZ_6"))):
+ (material == "PLA_VP" and machine_type.startswith("lulzbot_TAZ_6"))):
types = types + "|First Run"
order = 0
f.write("material_types = %s\n" % types)
~ianmdlvl / cura.git / commitdiff