+udev - userspace device management
-udev - a userspace implementation of devfs
+For more information see the files in the docs/ directory.
-For more information on the design, and structure of this project, see the
-files in the docs/ directory.
+Important Note:
+ Integrating udev in the system has complex dependencies and differs from distro
+ to distro. All major distros depend on udev these days and the system may not
+ work without a properly installed version. The upstream udev project does not
+ recommend to replace a distro's udev installation with the upstream version.
-To use:
+Requirements:
+ - Version 2.6.25 of the Linux kernel with sysfs, procfs, signalfd, inotify,
+ unix domain sockets, networking and hotplug enabled.
-- You must be running a 2.6 version of the Linux kernel.
+ - For reliable operation, the kernel must not use the CONFIG_SYSFS_DEPRECATED*
+ option.
-- Your 2.6 kernel must have had CONFIG_HOTPLUG enabled when it was built.
+ - Unix domain sockets (CONFIG_UNIX) as a loadable kernel module is not
+ supported.
-- Make sure sysfs is mounted. udev will figure out where sysfs is mounted, but
- the traditional place for it is at /sys. You can mount it by hand by running:
- mount -t sysfs none /sys
+ - The proc filesystem must be mounted on /proc/, the sysfs filesystem must
+ be mounted at /sys/. No other locations are supported by udev.
-- Make sure you have the latest version of the linux-hotplug scripts. They are
- available at linux-hotplug.sf.net or from your local kernel.org mirror at:
- kernel.org/pub/linux/utils/kernel/hotplug/
- They are required in order for udev to work properly.
+ - The system must have the following group names resolvable at udev startup:
+ disk, cdrom, floppy, tape, audio, video, lp, tty, dialout, kmem.
+ Especially in LDAP setups, it is required, that getgrnam() is able to resolve
+ these group names with only the rootfs mounted, and while no network is
+ available.
- If for some reason you do not install the hotplug scripts, you must tell the
- kernel to point the hotplug binary at wherever you install udev at. This can
- be done by:
- echo "/sbin/udev" > /proc/sys/kernel/hotplug
+Operation:
+ Udev creates and removes device nodes in /dev/, based on events the kernel
+ sends out on device discovery or removal.
-- Build the project:
- make
-
- Note:
- There are a number of different flags that you can use when building
- udev. They are as follows:
- prefix
- set this to the default root that you want udev to be
- installed into. This works just like the 'configure --prefix'
- script does. Default value is ''. Only override this if you
- really know what you are doing.
- USE_KLIBC
- if set to 'true', udev is built and linked against the
- included version of klibc. Default value is 'false'.
- USE_LOG
- if set to 'true', udev will emit messages to the syslog when
- it creates or removes device nodes. This is helpful to see
- what udev is doing. This is enabled by default. Note, if you
- are building udev against klibc it is recommended that you
- disable this option (due to klibc's syslog implementation.)
- USE_DBUS
- if set to 'true', DBUS messages will be sent everytime udev
- creates or removes a device node. This requires that DBUS
- development headers and libraries be present on your system to
- build properly. Default value is 'false'.
- USE_SELINUX
- if set to 'true', SELinux support for udev will be built in.
- This requires that SELinux development headers and libraries be
- present on your system to build properly. Default value is
- 'false'.
- DEBUG
- if set to 'true', debugging messages will be sent to the syslog
- as udev is run. Default value is 'false'.
- KERNEL_DIR
- If this is not set it will default to /lib/modules/`uname -r`/build
- This is used if USE_KLIBC=true to find the kernel include
- directory that klibc needs to build against. This must be set
- if you are not building udev while running a 2.6 kernel.
-
- So, if you want to build udev using klibc with debugging messages, you
- would do:
- make USE_KLIBC=true DEBUG=true
-
-- Install the project:
- make install
-
- This will put the udev binary in /sbin, create the /udev and /etc/udev
- directories, and place the udev configuration files in /etc/udev. You
- will probably want to edit the namedev.* files to create custom naming
- rules. More info on how the config files are set up are contained in
- comments in the files, and is located in the documentation.
-
-- Add and remove devices from the system and marvel as nodes are created
- and removed in /udev/ based on the device types.
-
-- If you later get sick of it, uninstall it:
- make uninstall
-
-
-Things are still quite rough, but it should work properly. If nothing
-seems to happen, make sure your build worked properly by running the
-udev-test.pl script as root in the test/ subdirectory of the udev source
-tree.
-
-Development and documentation help is very much appreciated, see the TODO
-file for a list of things left to be done.
-
-
-Any comment/questions/concerns please let me and the other udev developers
-know by sending a message to the linux-hotplug-devel mailing list at:
- linux-hotplug-devel@lists.sourceforge.net
-
-greg k-h
-greg@kroah.com
+ - Early in the boot process, the /dev/ directory should get a 'tmpfs'
+ filesystem mounted, which is maintained by udev. Created nodes or changed
+ permissions will not survive a reboot, which is intentional.
+ - The content of /lib/udev/devices/ directory which contains the nodes,
+ symlinks and directories, which are always expected to be in /dev, should
+ be copied over to the tmpfs mounted /dev, to provide the required nodes
+ to initialize udev and continue booting.
+ - The old hotplug helper /sbin/hotplug should be disabled in the kernel
+ configuration, it is not needed, and may render the system unusable
+ because of a fork-bombing behavior.
+ - All kernel events are matched against a set of specified rules in
+ /lib/udev/rules.d/ which make it possible to hook into the event
+ processing to load required kernel modules and setup devices. For all
+ devices the kernel exports a major/minor number, udev will create a
+ device node with the default kernel name, or the one specified by a
+ matching udev rule.
+Please direct any comment/question/concern to the linux-hotplug mailing list at:
+ linux-hotplug@vger.kernel.org