topeak-mtx-tortec-expeditionrack-adapter.scad

   1 // -*- C -*-
   2
   3 // brk_*: "bracket", the Topeak MTX bracket
   4 // rack_*: the Tortec rack
   5 // adapt_*: the adapter, ie this file
   6
   7 include <utils.scad>
   8
   9 // strength factor, set to 1 for real prints
  10 //$strf = 0.25;
  11 $strf = 1;
  12
  13 brk_recess_actual = 5.20;
  14
  15 rack_rail_dia = 10.40 + 0.30;
  16 rack_width_inner = 115.86 - 1.0; // between insides of rails
  17
  18 rear_elevation_nominal = 10.04;
  19 // ^ top of rack to bottom of bracket, at rack cross rail (fam)
  20 rear_to_front_distance = 230; // rack cross rail (fam) to very front end
  21 rear_to_cross_rail = 35.05; // bolt centre to rail centre, rail to rear
  22 rear_bolt_to_front_bolt = 155.4;
  23
  24 general_gap_y = 1.0;
  25
  26 strap_w = 8.0 + 1.0;
  27 strap_th = 2.5;
  28 strap_barrel_dia = 14;
  29 strap_guide_sz = 1;
  30
  31 brk_block_xw = 68.5;
  32 brk_block_z = 14.55 - 0.75;
  33
  34 brk_bolt_dia = 4.0 + 0.5;
  35 brk_nearbolt_recess_dia = 8.86 + 1.5;
  36 brk_nearbolt_recess_depth = 1.09 + 0.25;
  37
  38 brk_bolt_eff_len = 11.78 - 1.0; // inside of recess, to end of bolt
  39 brk_bolt_len_slop = 2.0;;
  40 brk_bolt_nut_th = 3.89;
  41 brk_bolt_nut_across_flats = 7.86 + 0.50;
  42
  43 brk_overall_w = 90.07;
  44
  45 fit_slope_len = 5;
  46
  47 // "foreaftmaint" aka "fam" is the hook-like part that stops
  48 // the adapter sliding forwards/backwards along the rails
  49 foreaftmaint_r_slop = 0.75;
  50
  51 main_sz_y = $strf * 18;
  52 grasp_sz = $strf * 6;
  53 grasp_thin_sz = $strf * 0.5;
  54 beside_strap_sz = $strf * 8;
  55 main_sz_core_z = $strf * 18;
  56
  57 // "length" in for-aft direction of interaction with rack rail
  58 min_on_rail_sz_z = $strf * 25;
  59
  60 $fa=10;
  61 $fs=1;
  62
  63 // calculated
  64
  65 main_sz_rhs_z = max(min_on_rail_sz_z, beside_strap_sz*2 + strap_w);
  66 main_sz_lhs_z = min_on_rail_sz_z;
  67
  68 main_sz_x_fam = main_sz_y;
  69
  70 brk_bottom_y = -brk_recess_actual;
  71 adapt_main_top_y = brk_bottom_y - general_gap_y;
  72
  73 // on LHS, so -ve
  74 rack_rail_x = -(rack_width_inner/2 + rack_rail_dia/2);
  75 rack_rail_outer_x = -(rack_width_inner/2 + rack_rail_dia);
  76
  77 grasp_large_r = (rack_rail_dia + grasp_sz)/2;
  78 grasp_small_r = (rack_rail_dia + grasp_thin_sz)/2;
  79 grasp_large_x = rack_rail_outer_x + grasp_large_r;
  80 grasp_small_x = rack_rail_outer_x + grasp_small_r;
  81
  82 block_x = grasp_large_x + grasp_large_r;
  83 block_y_min = adapt_main_top_y - main_sz_y;
  84
  85 strap_barrel_x = rack_width_inner/2 + strap_barrel_dia/2;
  86
  87 rack_shear_ratio = -rear_elevation_nominal / rear_to_front_distance;
  88
  89 brk_bolt_nut_top_y = -brk_nearbolt_recess_depth
  90   - brk_bolt_eff_len + brk_bolt_nut_th + brk_bolt_len_slop;
  91
  92 brk_bolt_nut_r = brk_bolt_nut_across_flats/2 / cos(360/12);
  93
  94 function elevation_of_bolt_for(z) = rear_elevation_nominal
  95   - (z - brk_block_z/2) * rack_shear_ratio;
  96
  97 function rack_rail_y_of_elevation(elevation_nominal) =
  98   brk_bottom_y - elevation_nominal - general_gap_y  - rack_rail_dia/2;
  99
 100 echo(rack_shear_ratio);
 101
 102 module GraspElevation(){
 103   hull(){
 104     translate([ grasp_large_x, adapt_main_top_y - grasp_large_r ])
 105       circle(grasp_large_r);
 106
 107     translate([ grasp_small_x, $rack_rail_y - rack_rail_dia/2 ])
 108       circle(grasp_small_r);
 109
 110     translate([ rack_rail_x + grasp_large_r/2,
 111                 $rack_rail_y - rack_rail_dia/2 ])
 112       circle(grasp_small_r);
 113
 114     translate([ grasp_large_x, $rack_rail_y + rack_rail_dia/2 ])
 115       circle(grasp_large_r);
 116
 117     translate([ grasp_large_x + grasp_large_r/2,
 118                 $rack_rail_y + rack_rail_dia/2 ])
 119       circle(grasp_large_r);
 120   }
 121 }
 122
 123 module BlockElevation(){
 124   hull(){
 125     rectfromto([ +block_x, adapt_main_top_y ],
 126                [ -block_x, block_y_min ]);
 127     rectfromto([ -grasp_large_x, adapt_main_top_y ],
 128                [ +grasp_large_x, adapt_main_top_y - 0.1 ]);
 129   }
 130   hull(){
 131     rectfromto([ +block_x, adapt_main_top_y ],
 132                [ -block_x, block_y_min ]);
 133     rectfromto([ grasp_large_x, block_y_min ],
 134                [ 0, block_y_min + 0.1 ]);
 135   }
 136 }
 137
 138 module MainExtrude(z){
 139   linextr(0, z)
 140     children();
 141 }
 142 module RackShear(){
 143   s = rack_shear_ratio;
 144   multmatrix([ [ 1, 0,  0, 0 ],
 145                [ 0, 1, s , 0 ],
 146                [ 0, 0,  1, 0 ],
 147                [ 0, 0,  0, 1 ] ])
 148     children();
 149 }
 150
 151 module GraspFixingElevation(){
 152   intersection(){
 153     union(){
 154       hull(){
 155         mirror([1,0]) {
 156           GraspElevation();
 157         }
 158         translate([ -block_x, block_y_min ] + [0,0.1]*1 )
 159           circle(0.1);
 160       }
 161       translate([ strap_barrel_x, $strap_barrel_y ])
 162         circle(strap_barrel_dia/2 + strap_guide_sz);
 163     }
 164     union(){
 165       rectfromto([0, $rack_rail_y],
 166                  [rack_width_inner, 50]);
 167       intersection(){
 168         translate([ rack_rail_x, $rack_rail_y ])
 169           circle(r = rack_width_inner/2 - rack_rail_x);
 170         polygon([ [ -block_x-0.1, 0 ],
 171                   [ rack_width_inner/2, 0 ],
 172                   $rail_fixing_fit_corner,
 173                   $rail_fixing_fit_corner + [-1,-1] * fit_slope_len,
 174                   [ -grasp_large_x - grasp_large_r*2, block_y_min ],
 175                   [ -block_x-0.1 -2, block_y_min +2 ]]);
 176       }
 177     }
 178   }
 179 }
 180
 181 module StrapBarrelElevation(){
 182   translate([ strap_barrel_x, $strap_barrel_y ])
 183     circle(strap_barrel_dia/2);
 184 }
 185
 186 // Bracket support block, goes up inside bracket
 187 // Z origin is bolt hole
 188 module BrkBlock(){
 189   linextr( -brk_block_z/2,
 190            +brk_block_z/2 ) {
 191     rectfromto([ -brk_block_xw/2, adapt_main_top_y - 0.1 ],
 192                [ +brk_block_xw/2, 0 ]);
 193   }
 194 }
 195
 196 // Z origin is bolt hole
 197 module BoltHole(){
 198   linextr_y_xz( -100, 10 )
 199     circle(brk_bolt_dia/2);
 200
 201   linextr_y_xz( -brk_nearbolt_recess_depth, 10)
 202     circle(brk_nearbolt_recess_dia/2);
 203
 204   linextr_y_xz( -100, brk_bolt_nut_top_y ) {
 205     circle( r= brk_bolt_nut_r, $fn = 6 );
 206     translate([ 0, brk_bolt_nut_across_flats/2 ])
 207       circle( r=brk_bolt_nut_r/2, $fn = 4);
 208   }
 209 }
 210
 211 module IfFam(){
 212   if ($foreaftmaint_dz) {
 213     children();
 214   }
 215 }
 216
 217 module FamLinextr(){
 218   IfFam()
 219     linextr_x_yz(-main_sz_x_fam/2, +main_sz_x_fam/2)
 220     children();
 221 }
 222
 223 module Principal(){
 224   // calculated
 225   $rack_rail_y = rack_rail_y_of_elevation($elevation_nominal);
 226
 227   $strap_barrel_y = $rack_rail_y + rack_rail_dia/2 + strap_barrel_dia/2;
 228
 229   $rail_fixing_fit_corner = [
 230     rack_width_inner/2,
 231     $rack_rail_y - rack_rail_dia/2
 232   ];
 233
 234   $foreaftmaint_rail_z = brk_block_z/2 + $foreaftmaint_dz;
 235
 236   difference(){
 237     union(){
 238       MainExtrude(main_sz_lhs_z){
 239         GraspElevation();
 240       }
 241       RackShear() MainExtrude(main_sz_rhs_z){
 242         StrapBarrelElevation();
 243       }
 244       translate([ 0,0, brk_block_z/2]) {
 245         BrkBlock();
 246       }
 247
 248       difference(){
 249         union(){
 250           MainExtrude(main_sz_core_z){
 251             BlockElevation();
 252           }
 253           if ($strf<1) {
 254             MainExtrude(max(brk_block_z, main_sz_rhs_z)){
 255               rectfromto([-8, 0],
 256                          [+8, block_y_min]);
 257               rectfromto([-block_x -5,  adapt_main_top_y],
 258                          [-grasp_large_x, block_y_min]);
 259             }
 260           }
 261           RackShear() MainExtrude(main_sz_rhs_z){
 262             GraspFixingElevation();
 263           }
 264         }
 265
 266         translate([0,0, main_sz_rhs_z/2]) linextr(-strap_w/2, +strap_w/2) {
 267           translate([ rack_width_inner/2 - strap_th, 0 ])
 268             rectfromto([ 0, -50 ], [ 50, 50 ]);
 269         }
 270       }
 271
 272       RackShear()
 273         FamLinextr(){
 274           rotate(-90)
 275           difference(){
 276             union(){
 277               rectfromto([ -$foreaftmaint_rail_z, adapt_main_top_y ],
 278                          [ 0, block_y_min]);
 279               hull(){
 280                 ybot = $rack_rail_y - rack_rail_dia/2 + grasp_large_r
 281                   - fit_slope_len * 0.5;
 282                 for (y = [
 283                           ybot,
 284                           adapt_main_top_y - grasp_large_r
 285                           ])
 286                   for (dx= [-1,+1] * rack_rail_dia/2)
 287                     translate([ -$foreaftmaint_rail_z + dx, y ])
 288                       circle(r= grasp_large_r);
 289               }
 290             }
 291             translate([0, adapt_main_top_y])
 292                rectfromto([-500, 0], [500, 500]);
 293           }
 294         }
 295     }
 296
 297     RackShear() linextr(-10, main_sz_lhs_z+main_sz_rhs_z) {
 298       for (mx=[0,1]) {
 299         mirror([mx,0]) {
 300           translate([ rack_rail_x, $rack_rail_y ]){
 301             hull(){
 302               for (dx = [-rack_rail_dia, 0])
 303                 translate([dx, 0])
 304                   circle(r= rack_rail_dia/2);
 305             }
 306           }
 307         }
 308       }
 309     }
 310
 311     RackShear() IfFam(){
 312       // Distance from bolt hole, in backwards direction
 313       cr = rack_rail_dia/2 + foreaftmaint_r_slop;
 314       translate([ 0, $rack_rail_y, $foreaftmaint_rail_z ])
 315         linextr_x_yz(+rack_rail_x,
 316                      -rack_rail_x) {
 317         hull(){
 318           for (dy=[0,50]) {
 319             translate([-dy,0])
 320               circle(r= cr);
 321           }
 322         }
 323         hull(){
 324           for (dd=[[0,0], [-1,-1], [-1,+1]]) {
 325             translate(
 326                       [-1, 0] * (rack_rail_dia - fit_slope_len)
 327                       + 20 * dd
 328                       )
 329               circle(r= cr);
 330           }
 331         }
 332       }
 333     }
 334
 335     translate([ 0,0, brk_block_z/2]) BoltHole();
 336   }
 337 }
 338
 339 module RackForDemo(){ ////toplevel
 340   elevation = elevation_of_bolt_for(rear_to_cross_rail);
 341   rack_rail_y = rack_rail_y_of_elevation(elevation);
 342
 343   rotate([-atan(rack_shear_ratio), 0,0])
 344     translate([0, rack_rail_y, brk_block_z/2 + rack_rail_y*rack_shear_ratio]) {
 345       for (m=[0]) mirror([m,0,0]) {
 346         linextr(-50, 50 + rear_to_cross_rail)
 347           translate([rack_rail_x, 0])
 348           circle(r= rack_rail_dia/2);
 349         }
 350       translate([0,0, rear_to_cross_rail])
 351         linextr_x_yz(rack_rail_x, -rack_rail_x)
 352         circle(r= rack_rail_dia/2);
 353     }
 354 }
 355
 356 module Front(){ ////toplevel
 357   // xxx elevation is wrong
 358   Principal($elevation_nominal=
 359       elevation_of_bolt_for(rear_to_cross_rail + rear_bolt_to_front_bolt),
 360             $foreaftmaint_dz= 0);
 361 }
 362
 363 module Rear(){ ////toplevel
 364   Principal($elevation_nominal=
 365       elevation_of_bolt_for(rear_to_cross_rail),
 366             $foreaftmaint_dz= rear_to_cross_rail);
 367 }
 368
 369 module SomeDemo(){
 370   rotate([90, 0, 0]){
 371     children();
 372
 373     color("blue")
 374       translate([ 0, -2, -4 ])
 375       square(center=true, [ brk_overall_w, 1 ]);
 376
 377   }
 378 }
 379
 380 module FrontDemo(){ ////toplevel
 381   SomeDemo() Front();
 382 }
 383 module RearDemo(){ ////toplevel
 384   SomeDemo() Rear();
 385 }
 386 module RearRackDemo(){ ////toplevel
 387   rotate([atan(rack_shear_ratio),0,0]) SomeDemo() {
 388     Rear();
 389     %RackForDemo();
 390   }
 391 }