3 // Hard case for Fairphone 2
5 // Copyright 2018 Ian Jackson. There is NO WARRANTY.
6 // See below for full licensing and disclaimer.
10 // 1. You will want to git clone this repository.
12 // 2. Decide about the notification LED aperture. See the variable
13 // led_window_style, below. The default here is "ad-hoc
14 // multi-colour", which can produces a translucent (clear-ish)
15 // window set into the lid, even on a single-nozzle printer.
16 // See "Ad-hoc multi-colour", below.
18 // 3. use "make" to generate the necessary files:
20 // make -j8 fairphone-case.auto.scads `for f in \
26 // ; do echo fairphone-case,$f.auto.stl; done`
28 // 4. Print them. Case and OneKeeperPrint should probably be
31 // For Lid and LidWindowPrint, if you are doing ad-hoc
33 // i. Set up for clear filament
34 // ii. Print LidWindowPrint. Wait for it to finish.
35 // It won't take long. As soon as it finishes, tell
36 // your printer to warm up (so that in fact it does
38 // iii. Leaving the output so far on the printbed, reload
39 // your printer with the main lid colour.
40 // iv. Print LidPrint. You can let this go unattended.
42 // 5. Assemble the hinge. You will need 4x M2 12mm machine screws
43 // and 8x M2 full nuts.
45 // Make sure you get the hinge the right way round. If you're not
47 // openscad fairphone-case,DemoHinge.auto.scad
48 // to see an assembly diagram.
50 // The nuts recess into the hinge. You will want very fine
51 // pliers. As you screw each screw in, add the second nut when
52 // the screw thread emerges from the first - this will be a
53 // locknut. Screw each screw to an appropriate tightness for the
54 // hinge stiffness. You want the lid-side hinge to be stiffer as
55 // that makes closing the case work better.
57 // When you have the stiffness right, tighten the locknuts onto
62 // - To put the phone in, drop its RH side into the RH side of
63 // the case. Then feed the keeper through the small hole.
64 // Feed it right through.
66 // - The optional prop can be used to prop the phone up (in
67 // portrait orientation only right now). See
68 // openscad fairphone-case,DemoPropAngles.auto.scad
70 // Ad-hoc multi-colour
72 // This file is set up to let you make a translucent window using a
73 // single-extruder printer, using a "two print run" technique. This
74 // works well with our Lulzbot TAZ 5 and Aleph Objects' version of
75 // Cura. If you are using a different printer, you may need to
76 // adjust the parameters or try a different technique. In particular,
77 // initial_layer_thick
78 // set so that the window is one layer thick
79 // initial_layer_width
80 // set so that the slicer draws a rectangle around the whole
81 // object, rather than putting a "skirt" or anything inside
83 // If you have a dual-extruder printer, you can set led_window_style
84 // to 2 and do a single print of LidPrint and LidWindowPrint.
86 // Alternatively you can set it to 1 (just a hole) or 0 (no hole).
88 // Thanks to Clare Boothby for the ad-hoc multi-colour technique (and
89 // the parameters for our Lulzbot TAZ 5 and Aleph Objects's Cura).
93 // It might well be possible to adapt this file for other phones.
94 // If you do, let me know how you get on.
97 // AUTHORSHIP, COPYRIGHT, LICENCE, AND LACK OF WARRANTY
99 // Copyright (C)2018 Ian Jackson.
101 // This program for generating a 3D model is free software: you can
102 // redistribute it and/or modify it under the terms of the GNU
103 // General Public License as published by the Free Software
104 // Foundation, either version 3 of the License, or (at your option)
105 // any later version.
107 // This program is distributed in the hope that it will be useful,
108 // but WITHOUT ANY WARRANTY; without even the implied warranty of
109 // MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
110 // GNU General Public License for more details.
112 // You should have received a copy of the GNU General Public
113 // License along with this program. If not, see
114 // <http://www.gnu.org/licenses/>.
116 // In particular DO NOT BLAME ME IF THIS CASE DOES NOT ADEQUATELY
117 // PROTECT YOUR PHONE ! It is your responsibility to decide whether
118 // this case will meet your needs.
123 phone = [ 75.0, 145.0 ];
125 prop_buildout_less = 3;
127 prop_angles = [ 15, 30, 45, 60 ];
129 bumper = [ 0.250, -0.025 ];
130 // ^ One side. Overall size is increased by twice this.
131 // If no bumpers, is the gap around the phone.
135 led_window_style = 3;
137 // 1: simply an opening
138 // 2: opening with separate cover model, for printing in clear (two colour)
139 // 3: like 2 but one-layer window for ad-hoc multi-colour
141 initial_layer_thick = 0.400; // ^ needed for mode 3 only
142 initial_layer_width = 0.750; // ^ needed for mode 3 only
143 multicolour_gap = 0.15; // each side
146 phone_rim_depth = 0.80; // includes allowance for a screen protector
148 button_cutout_depth = 9;
150 phone_edge_thick = 9.0;
151 phone_total_thick = 12.0;
152 phone_backside_slope_inner = 1.5; // larger means shallower
153 phone_backside_slope_outer = 1.0; // larger means shallower
155 camera_pos_tl = [ 6.450, 12.750 ]; // measured from tl corner
156 camera_pos_br = [ 22.300, 37.600 ]; // tl/br as seen from back
158 jack_pos = [ 13.83, 8.485 ];
159 jack_dia = 10.64 + .5; // some jack I had lying around
161 led_pos = [ 13.98, 10.00 ];
163 led_window_ledge = 0.75; // each side
165 noisecancelmic_pos = [ 19.54, 7.37 ]; // from rhs
166 noisecancelmic_dia = 4.00;
168 //fingerpushhole_dias = [ 15, 18 ];
169 fingerpushhole_dias = [];
171 lanyard_half_dia = 1.15;
172 lanyard_entry_rel_breadth = 2;
173 lanyard_channel_len = 15;
174 rearspeaker_pos_bl = [ 12.64, 18.72 ];
175 rearspeaker_size = [ 3.76, 7.36 ];
177 microusb_above = 3.27 - 0.25;
178 microusb_below = 0.0;
179 microusb_width = 16.12 + 1.25;
181 case_th_bottom = 2.5;
186 lid_screen_gap_extra = .66;
188 case_struts_count = 6;
189 case_struts_solid_below = 1.00;
190 case_struts_solid_above = 0.75;
191 case_struts_width = 0.10;
195 keeper_inner_width = 2.75;
196 keeper_inner_height = 2.75;
197 keeper_slant_slope = 2; // larger means steeper
199 keeper_gap_z_top = 0.25;
200 keeper_gap_z_bot = 0.75;
202 keeper_gap_x_holes = 0.75;
204 keeper_side = 0; // 0 = lhs; 1 = rhs
211 lid_edgepart_width = 5.0;
212 lid_buttoncover_thick = 1.3;
217 foldover_lever_gap = 0.50;
219 // properties of the hinge fasteners
220 hingescrew_shaft_dia = 2.0 + 0.25; // M2 x 12mm machine screw
221 hingescrew_shaft_len = 12;
222 hingescrew_fasteners_extra_thick = 0.40;
223 // ^ amount of thread protruding if everything was completely nominal
224 // and we are using two nuts
225 hingescrew_nut_access_dia = 4.72 + 0.50;
226 // ^ washer is 4.72 dia
227 // also, want to get pliers or tiny spanner in to do up locknut
228 hingescrew_nut_across = 3.92 + 0.25; // incl. slop around recess slop
229 hingescrew_nut_thick = 1.93;
230 hingescrew_head_th = 1.38 + 0.75;
231 hingescrew_head_dia = 3.92;
233 hingescrew_nut_recess_portion = 2/3; // portion of nut in recess
235 lever_cover_th = 0.75;
237 hingemount_wd = 4.8725;
242 button_l_fudge = 4.4;
243 buttonishleg_default_l_is_fudge = 10;
245 hinge_base_slope = 1.5; // bigger is steeper
247 strut_min_at_end = 1.5;
250 hinge_x_postscrew_gap = 0.75;
251 hinge_x_arms_gap = 0.35;
252 hinge_r_arms_gap = 0.55;
254 rearspeaker_gap = [ 2.0, 2.0 ]; // each side
258 catch_thickness = 1.3;
259 catch_side_gap = 0.75; // each side
263 catch_finger_height = 1.5;
264 catch_finger_depth = 2.5;
265 catch_catch_slope = 0.25;
267 catch_topcurve_r = 5.0;
269 prop_recess_under = 0.50;
270 prop_recess_slop = 0.200; // each side
275 prop_side_gap = 0.75; // each side
276 prop_lidrecess_behind = 0.75;
277 prop_caserecess_behind = 0.75;
278 prop_caserecess_taper = 0.45; // one side only
280 prop_prong_heel_slope = 0.5;
282 lid_fold_clearance_antislop = 0.5;
284 // ---------- calculated ----------
286 phone_width = (phone + bumper*2)[0];
287 phone_height = (phone + bumper*2)[1];
289 inside_br = [phone_width, -phone_height];
291 prop_prong_h = prop_main_th;
293 //echo(camera_pos_tl + bumper,
294 // camera_pos_br + bumper);
296 // ----- could be changed -----
297 lid_buttoncover_gap = lid_gap_x;
298 lid_buttoncover_overlap = case_th_lip + keeper_gap_z_top;
300 phone_backside_slope_thick = phone_total_thick - phone_edge_thick;
302 //prop_lidrecess_depth = case_th_lid - prop_recess_under;
304 //prop_nose_len = case_th_lid - prop_recess_under;
305 //prop_recess_slope = tan(prop_max_angle); // bigger means steeper
306 //prop_recess_width = prop_main_th / cos(prop_max_angle) + prop_backfwd_gap;
309 //lid_lip_overlap_width xxx bad name = ;
310 //lid_lip_inner_slope = [ 5, 5 ]; // xxx
313 epp1 = [0, -phone_edge_thick];
314 epp2i = epp1 + phone_backside_slope_thick * [ phone_backside_slope_inner, -1 ];
315 epp2o = epp1 + phone_backside_slope_thick * [ phone_backside_slope_outer, -1 ];
316 epp3 = epp2i + [10, 0];
317 epp5 = epp0 + [0,1] * (keeper_th_z + keeper_gap_z_top + case_lip);
318 epp4 = epp5 + [-1,0] * case_th_side;
321 kppd = kppe + [1,0] * keeper_inner_width;
322 kppc = kppd + [0,1] * keeper_th_z;
323 kppb = [ kppe[0] - keeper_th_x, kppc[1] ];
324 kppf = kppe - [0,1] * keeper_inner_height;
325 kppa = [ kppb[0], kppf[1] ];
327 lpp10 = [ epp5[0] + lid_gap_x, kppc[1] + lid_gap_z ];
328 lpp11 = [ lpp10[0], epp5[1] + lid_gap_z ];
330 lpp14 = lpp10 + [1,0] * max(keeper_inner_width, lid_edgepart_width);
331 // exact x posn not very important; must extend past end of keeper
334 epp0[1] - phone_rim_depth + 1/2.5 * case_th_lid
335 + lid_screen_gap_extra ];
336 // ^ beam theory says to maximise force before contact,
337 // the gap below the `beam' (the lid) must be 1/3
338 // the thickness (ie the lid thickness) if the beam
339 // is solid, or 1/2 if it has a top and bottom only.
340 // ours is mostly solid.
342 lp_r12 = max(case_th_lid - (lpp11[1] - lpp15[1]),
345 lpp12 = [ epp4[0] + lp_r12, lpp11[1] ];
346 lpp13 = [ lpp12[0], lpp12[1] + lp_r12 ];
348 case_bottom_z = epp2o[1] - case_th_bottom;
352 bppN = [ bppM[0] + lid_buttoncover_thick, bppM[1] ];
353 bppR = [ bppN[0] + lid_buttoncover_gap, -button_cutout_depth ];
354 bppS = [ epp1[0], bppR[1] ];
355 bppQ = [ bppM[0], bppR[1] - lid_buttoncover_overlap ];
356 bppP = bppQ + [0,1] * lid_buttoncover_gap;
357 bppO = [ bppN[0], bppP[1] ];
358 bppL = lpp10 + [5,0];
359 bppK = [ bppL[0], bppN[1] ];
360 bppJ = [ bppN[0], bppL[1] ];
361 bppU = [ bppJ[0], lpp12[1] ];
365 echo("BUTTON COVER TH", bppO[0] - bppP[0]);
367 // notification led aperture
369 nla_r0 = led_aperture/2;
370 nla_r1 = nla_r0 + led_window_ledge;
371 nla_r2 = nla_r1 + multicolour_gap;
373 led_window_style >= 3 ? initial_layer_thick :
374 led_window_style >= 2 ? led_window_ledge : 0;
378 hp_rn = hingescrew_nut_access_dia/2;
379 hp_r2_min = hp_rn + lever_cover_th;
380 hp_rs = hingescrew_shaft_dia/2;
381 hp_r1_min = hp_rs + hingemount_th;
383 hp_r1 = max(hp_r1_min, hp_r2_min);
387 hppS = epp2o + [0,-1] * case_th_bottom;
388 hp_k = 0.5 * (hppU[1] - hppS[1] + foldover_gap);
390 hppM = [ epp4[0] - foldover_lever_gap - hp_r2,
391 0.5 * (hppU + hppS)[1] ];
392 hppT = [ hppM[0], hppU[1] - hp_r1 ];
393 hppB = hppT + [0,-1] * hp_k;
395 hppE_y = epp2o[1] - case_th_bottom + hp_r1;
396 hppE_x = hppB[0] + (hppB[1] - hppE_y) * hinge_base_slope;
397 hppE = [ hppE_x, hppE_y ];
399 // hinge elevation x coords
401 hex20 = max(epp2o[0],
403 kppd[0] + hingescrew_head_th + keeper_gap_x_holes);
404 hex21 = hex20 + hingemount_wd;
405 hex22 = hex21 + hinge_x_gap;
406 hex27 = hex20 + hingescrew_shaft_len;
407 hex24 = hex27 + hinge_x_postscrew_gap;
408 hex23 = hex27 - (hingescrew_nut_thick*2
409 + hingescrew_fasteners_extra_thick);
410 hex26 = hex23 + hingescrew_nut_thick * 2/3;
412 echo(hex20, hex21, hex22, hex23, hex24);
413 // 6, 10.8725, 10.9975, 13.74, 18.75
414 module chk(act,exp) {
415 if (abs(act-exp) > 1e-9) echo("WRONG", act, exp);
416 else echo("ok", act);
424 lid_fold_clearance_skew =
425 (lpp10[1] - hppB[1]) /
426 (lpp10[0] - hppB[0]);
428 echo("SK",lid_fold_clearance_skew);
432 cppJ = [ epp4[0] + catch_thickness, lpp10[1] ];
433 cppA = cppJ + [lid_gap_x, -lid_gap_z];
434 cppB = [ epp0[0], cppA[1] ];
435 cppP = [ epp4[0], cppJ[1] ];
437 cppS = cppJ + [0,-1] * catch_len;
438 cppD = [ cppA[0], cppS[1] + catch_slop ];
439 cppC = [ cppB[0], cppD[1] ];
440 cppT = cppS + [1, -catch_catch_slope] * catch_depth;
441 cppU = cppT + [0,-1] * catch_height;
442 cppV = [ cppS[0], cppU[1] - catch_depth ];
444 cppR = 0.5*(cppP + cppJ);
446 cp_rQ = 0.5 * (cppJ[0] - cppP[0]);
448 cppV[1] - (catch_finger_height - cp_rQ) ];
449 cppF = [ cppV[0] + catch_finger_depth, cppC[1] ];
453 ly_r = lanyard_half_dia / 2;
456 ly_theta = -atan2vector(epp2i - epp1);
457 ly_o = epp2i + 3 * ly_r * unitvector2d(epp1 - epp2i);
459 max_case_bottom_edge_thickness =
461 + sin(ly_theta) * (epp2i-epp2o)[0];
463 ly_q_z = -(ly_rc + ly_r);
464 ly_re = max_case_bottom_edge_thickness - (-ly_q_z);
466 ly_oec_y = lanyard_entry_rel_breadth * ly_r;
468 // prop recess in case
470 prop_x_pos = phone_width/2;
472 prop_recess_hw = 0.5 * prop_main_width + prop_side_gap;
474 prc_r1 = prop_end_dia/2;
475 prc_r3 = prc_r1 + prop_recess_slop;
477 prcp2 = [ epp4[0] + prop_buildout_less,
480 prop_caserecess_buildout_r = -1; // prcp2[0] - epp2o[0];
482 prcp1 = [ epp2o[0] + prc_r3 + prop_caserecess_behind,
483 epp2i[1] - prc_r3 - prop_recess_under];
485 // prop recess in lid
487 prl_r10 = prop_end_dia/2;
488 prl_r10o = prl_r10 + prop_recess_slop;
490 prlp10 = lpp10 + [1,1] * prl_r10o
491 + [1,0] * prop_lidrecess_behind
492 + [0,1] * prop_recess_under;
497 $prpp11 = [0, prop_taper_len];
501 // ---------- modules ----------
503 module AdhocMultiprintFrame(phase, z0, zs) {
504 // from z0 to z0 + zs*layer
505 extra = phase * (initial_layer_width + multicolour_gap) + 5;
506 xextra = extra + -epp4[0];
507 xrange = [ 0, phone_width ] + [-1,+1] * xextra;
508 yextra = extra + -epp4[0];
509 yrange = [ -phone_height + +hppB[0] - hp_r2, 0 ] + [-1,+1] * yextra;
510 p0 = [ xrange[0], yrange[0] ];
511 p1 = [ xrange[1], yrange[1] ];
514 mirror([0,0, zs<0 ? 1 : 0])
515 linear_extrude(height= initial_layer_thick)
517 rectfromto(p0 - [1,1] * initial_layer_width,
518 p1 + [1,1] * initial_layer_width);
523 module KeeperProfile(slant=0){
524 use_e = kppe + [0,-1] * slant * keeper_inner_width / keeper_slant_slope;
525 polygon([use_e, kppd, kppc, kppb, kppa, kppf]);
528 module EdgeProfile(){
531 translate(epp3) square(case_th_bottom*2, center=true);
532 circleat(epp2o, r=case_th_bottom);
533 circleat(epp1, r=case_th_side);
534 rectfromto(epp0, epp4);
536 polygon([ epp5 + [0,10],
543 module LanyardLanyardProfile(entry=false){
545 for (xs=[-1,+1] * (entry ? lanyard_entry_rel_breadth : 1))
546 translate(xs * 0.5 * lanyard_half_dia * [1,0])
547 circle(r= lanyard_half_dia/2);
551 module LanyardCurveChannelProfile(){
552 translate([0, -ly_r])
553 LanyardLanyardProfile();
556 module LanyardEntryChannelProfile(){
557 LanyardLanyardProfile(true);
560 module LanyardMainChannelProfile(){
561 LanyardCurveChannelProfile();
563 square(center=true, ly_r * [6, 2]);
565 translate(ly_r * [3 * xs, -1])
570 module LanyardEntryOuterProfile(){
571 circleat([ly_re + ly_r, 0], ly_re);
574 module LanyardEntry(){
580 translate([d_x, 0, q_z]) {
583 rotate_extrude(convexity=10)
586 LanyardCurveChannelProfile();
594 linear_extrude(height=20)
596 LanyardEntryChannelProfile();
598 translate([0, ly_r*2, 0])
600 linear_extrude(height = ly_r*4){
602 rectfromto([d_x, q_z], [ly_r, 0]);
603 circleat([d_x, q_z], ly_rc);
607 translate([0,0,q_z]){
610 translate([0, oec_y, 0]){
612 translate(ly_re * [-1,0,-2])
613 cube(ly_re * [2,1,2]);
614 rotate_extrude(convexity=10)
615 LanyardEntryOuterProfile();
620 translate([-ly_re, -(oec_y + 0.01), -2*ly_re])
621 cube([ly_re*2, 2*(oec_y + 0.01), 2*ly_re]);
626 linear_extrude(height=20)
627 LanyardEntryOuterProfile();
632 module LanyardCutout(l){
634 linear_extrude(height=l)
636 LanyardMainChannelProfile();
639 translate(ee * l * [-1,0])
645 module LidEdgeProfile(){
656 circleat(lpp12, r=lp_r12);
657 rectfromto( lpp12 + [-10, 0],
658 lpp12 + [+10, +10] );
662 module LidEdgeFoldClearanceProfile(){
663 translate([-lid_fold_clearance_antislop, 0])
672 module ButtonCoverProfile(){
674 polygon(concat([ bppM, bppP, bppO, bppJ ],
675 (enable_support && !$button_suppress_over_keeper
676 ? [ bppU, bppV, bppW ] : []),
685 module ButtonPlan(l, deep, cut){
687 (cut ? 0 : lid_buttoncover_gap);
690 (deep ? lid_buttoncover_overlap : 0);
692 C = [0,0]; // by definition
696 B0 = C + [0,-1] * button_cutout_depth;
697 B1 = B0 + [0,1] * epsilon;
699 r0 = 0.5 * (T[1] - B0[1]);
700 A = [ -(l + button_l_fudge)/2 + r0, 0.5 * (T[1] + B0[1]) ];
701 H = A + [0,-1] * delta;
707 E1 = E0 + [1,0] * epsilon;
709 I0 = [ E0[0], H[1] ];
710 I1 = [ E1[0], H[1] ];
713 for (m=[0,1]) mirror([m,0])
714 circleat(H, r0 - epsilon);
716 for (m=[0,1]) mirror([m,0]) {
726 circleat(D, r0 + epsilon);
731 module CatchCatchProfile(){
733 for (c=[ cppR, cppQ ])
737 circleat(lpp12, lp_r12);
738 circleat(lpp12 + [5,0], lp_r12);
739 rectfromto(cppP, cppP + [5,0.1]);
741 polygon([cppJ, cppS, cppT, cppU, cppV, cppQ, cppR]);
744 module CatchCutProfile(){
756 module Flip_rhs(yn=[0,1]) {
758 translate([phone_width/2, 0, 0])
759 mirror([$rhsflip,0,0])
760 translate([-phone_width/2, 0, 0])
765 module Flip_bot(yn=[0,1]) {
767 translate([0, -phone_height/2, 0])
768 mirror([0, $botflip, 0])
769 translate([0, phone_height/2, 0])
774 module AroundEdges(fill_zstart, fill_th, fill_downwards=0){
777 translate([0, -phone_cnr_rad, 0])
779 linear_extrude(height = phone_height - phone_cnr_rad*2)
783 Flip_rhs() Flip_bot() {
784 translate([+1,-1] * phone_cnr_rad)
789 translate([-1,0] * phone_cnr_rad)
791 rectfromto([0,-20],[10,20]);
793 translate([-10, 0, -20] + 0.01 * [+1,-1, 0] )
799 translate([ phone_width - phone_cnr_rad, 0,0 ])
801 linear_extrude(height = phone_width - phone_cnr_rad*2)
805 translate([0,0, fill_zstart])
806 mirror([0,0, fill_downwards])
807 linear_extrude(height = fill_th)
808 rectfromto([+1,-1] * phone_cnr_rad,
809 [phone_width, -phone_height] + [-1,+1] * phone_cnr_rad);
812 module CaseAperture(pos, dia, $fn) {
814 translate([ pos[0] + bumper[0],
817 rotate([-90, theta, 0])
818 cylinder(r = dia/2 / cos(theta),
822 module SideButton(y, y_ref_sign, l, suppress_over_keeper=0){
824 // +1 measured from top of actual phone to top of button
825 // -1 measured from bottom of actual phone to bottom of button
826 // 0 y is centre of button in coordinate system
828 $button_suppress_over_keeper= suppress_over_keeper;
829 eff_y = y_ref_sign > 0 ? -bumper [1] -y -l/2 :
830 y_ref_sign < 0 ? (-phone -bumper)[1] +y +l/2 :
833 translate([0, eff_y, 0])
837 module LidButtonishLeg(y, y_ref_sign, l=buttonishleg_default_l_is_fudge) {
838 $button_leg_only = true;
839 SideButton(y, y_ref_sign, l) children();
843 Flip_rhs(1) SideButton(15.580, +1, 8.9 ) children(); // power
844 Flip_rhs(1) SideButton(48.700, -1, 8.920 ) children(); // camera
845 Flip_rhs(0) SideButton(30.800, +1, 21.96, 1) children(); // volume
846 Flip_rhs( ) LidButtonishLeg(14, -1) children();
847 // Flip_rhs(0) LidButtonishLeg(20, +1, 20) children();
850 module Struts(x_start, z_min, th){
851 // if th is negative, starts at z_min and works towards -ve z
852 // and object should then be printed other way up
853 for (i= [1 : 1 : case_struts_count]) {
857 mirror([0,0, th<0 ? 1 : 0])
859 -phone_height * i / (case_struts_count+1),
860 case_struts_solid_below])
861 linear_extrude(height= abs(th)
862 -(case_struts_solid_below+case_struts_solid_above))
863 rectfromto([ x_start, -0.5 * case_struts_width ],
864 [ phone_width - x_start, +0.5 * case_struts_width ]);
868 module OrdinaryRearAperture(rhs,bot, pos){
869 Flip_rhs(rhs) Flip_bot(bot)
872 translate(pos + bumper)
880 linextr(-epp2i[0], 60)
881 translate([0.5 * phone_width, 0, 0])
882 rectfromto([-microusb_width/2, epp2i[1] + microusb_below],
883 [+microusb_width/2, epp0[1] + -microusb_above]);
887 module OrdinaryRearApertures(){
889 OrdinaryRearAperture(1,1, rearspeaker_pos_bl)
890 rectfromto(-rearspeaker_gap,
891 rearspeaker_size + rearspeaker_gap);
893 // finger hole to remove phone
894 if (len(fingerpushhole_dias))
895 OrdinaryRearAperture(1,0, [ fingerpushhole_dias[0]/2 + epp2i[0],
897 scale(fingerpushhole_dias)
901 module RearCameraAperture(){
904 linear_extrude(height = 20)
907 rectfromto(camera_pos_tl, camera_pos_br);
910 module HingeLidProfile(){
912 circleat(hppT, hp_r1);
913 circleat(lpp12, lp_r12);
921 module HingeBaseProfile(){
924 circleat(hppB, hp_r1);
925 circleat(hppE, hp_r1);
926 circleat(epp2o, case_th_bottom);
927 circleat(hppB + [10,0], hp_r1);
929 polygon([epp5, epp1, epp2i, epp3, bppL]);
933 module HingeLeverOuterProfile(){
935 circleat(hppT, hp_r2);
936 circleat(hppB, hp_r2);
940 module HingeLeverInnerProfile(){
942 c = s > 0 ? hppT : hppB;
945 rotate(s<0 ? -40 : 0)
954 module HingeLeverNutProfile(){
955 for (c= [hppB, hppT]) {
957 circle($fn=6, r= 0.5 * hingescrew_nut_across / cos(30));
961 module Flip_hinge(doflip=1){
962 hinge_origin = [0, -(phone_height - hppB[0]), hppB[1]];
963 translate(hinge_origin)
964 rotate([doflip*180,0,0])
965 translate(-hinge_origin)
969 module HingePortion(x0,x1){
970 Flip_rhs() Flip_bot(1)
974 linear_extrude(height=x1-x0)
978 module CatchPortion(xwidth, ztop){
979 width = catch_width + xwidth;
980 w = width + catch_topcurve_r*2 + 1;
981 translate([phone_width/2, 0,0]){
986 translate([0, 50, 0])
988 linear_extrude(height=100){
989 for (m=[0,1]) mirror([m,0,0]) {
991 translate([w/2, ztop - catch_topcurve_r])
992 circle(catch_topcurve_r);
993 translate([w/2, -50])
994 square(catch_topcurve_r*2, center=true);
1003 AroundEdges(epp3[1], case_th_bottom, 1)
1007 function prop_x(gamma) = hp_k / (2 * sin(gamma/2)) - hppT[0];
1009 module PropProfileAssignments(gamma){
1010 // https://en.wikipedia.org/wiki/Solution_of_triangles#Two_sides_and_the_included_angle_given_(SAS)
1012 p = phone_height + prlp10[0] - hppB[0];
1015 q = phone_height - hppT[0] - prcp1[0]; // $prpp7[0] is 0 by definition
1017 c = sqrt(a*a + b*b - 2*a*b*cos(gamma));
1018 $prp_alpha = acos( (b*b + c*c - a*a) / (2*b*c) );
1020 $prp_theta = 90 - $prp_alpha;
1021 beta = 180 - $prp_alpha - gamma;
1024 //echo("abc", a,b,c);
1026 v1 = [ [ cos(psi), -sin(psi) ], // x
1027 [ sin(psi), cos(psi) ] ]; // y
1029 $prpp7 = [0, c + (lpp13[1] - $prpp10[1] - hp_k) ];
1032 $prp_r11 = prop_main_th/2;
1034 $prpp1 = $prpp7 + [1,0] *
1035 // this is approximate, but will do
1036 (prop_main_th/2 + prop_prop_gap + prcp1[0] - cppA[0]);
1039 v1[1] * ((prcp2[1] - prcp1[1]) - prop_prop_gap);
1040 $prpp12 = $prpp3 + v1[0] *
1041 (prop_end_dia + prop_caserecess_taper * ($prpp1[1] - $prpp3[1]));
1042 $prp_r8 = prop_main_th;
1043 $prpp4 = [ prop_main_th/2, $prpp3[1] ];
1045 $prpp5 = [ $prpp12[0] - $prp_r5,
1046 $prpp3[1] - prop_prong_h + $prp_r5 ];
1047 $prpp6 = $prpp4 + [0,-1] * (prop_prong_h +
1048 prop_prong_heel_slope * ($prpp5[0] - $prpp4[0]));
1049 $prpp8 = $prpp4 + [0,-1] * $prp_r8;
1050 $prpp9 = $prpp8 + [-1,0] * $prp_r8;
1055 module PropProfile(gamma, cut=0, rot=0){
1056 PropProfileAssignments(gamma){
1058 //#circleat($prpp3,1);
1059 //#circleat($prpp12,1);
1066 polygon([[-20,-0], [20,20], [0,0]]);
1068 rectfromto($prpp6, $prpp9);
1069 translate($prpp5) intersection(){
1071 polygon([[-10,-10], [0,0], [10,0]]);
1073 rectfromto($prpp12 + [0,-0.1], $prpp3);
1076 circleat($prpp1, $prp_r1);
1077 rectfromto($prpp12 + [0,-0.1], $prpp3);
1081 rotate([0,0, rot*-$prp_theta]){
1083 extra = cut ? prop_recess_slop : 0;
1084 rectfromto($prpp6, $prpp9);
1085 circleat($prpp11, $prp_r11 + extra);
1086 circleat($prpp10, $prp_r10 + extra);
1092 module PropAggregateProfile(){
1093 for (angle = prop_angles)
1094 PropProfile(angle, 0,0);
1097 module Prop(){ ////toplevel
1098 hw = prop_main_width/2;
1100 PropAggregateProfile();
1103 module Case(){ ////toplevel
1108 // ledge (fixed keeper)
1109 Flip_rhs(1-keeper_side) intersection(){
1111 linear_extrude(height = phone_height + phone_cnr_rad * 2)
1114 // outline of the whole case, to stop it protruding
1115 translate([0,0, -25])
1116 linear_extrude(height = 50)
1119 circleat([+1,-1] * phone_cnr_rad, phone_cnr_rad + case_th_side/2);
1123 HingePortion(hex20, hex21) HingeBaseProfile();
1125 // buildout for prop recess
1126 if (prop_caserecess_buildout_r > 0) Flip_rhs(1)
1127 linextr(case_bottom_z, epp2i[1])
1130 circleat([ prop_x_pos + dxs * prop_caserecess_buildout_r,
1132 r = epp2o[0] - prcp2[0]);
1137 Flip_rhs(keeper_side)
1138 translate([0, -phone_cnr_rad, 0])
1140 linear_extrude(height = phone_height + phone_cnr_rad * 2)
1143 rectfromto([ -keeper_gap_x, -keeper_gap_z_bot ],
1144 [ keeper_gap_x_holes, +keeper_gap_z_top ]);
1148 RearCameraAperture();
1150 // struts (invisible, because they're buried in the case)
1151 Struts(epp2i[0], epp2i[1] - case_th_bottom, case_th_bottom);
1156 if (!($button_leg_only && enable_support))
1158 translate([0,0,-10])
1159 linear_extrude(height= 20)
1160 ButtonPlan($button_l, 0,1);
1161 if ($button_leg_only)
1163 translate([phone_width/2, -400, kppe[1]])
1164 mirror([1-abs($rhsflip - keeper_side),0,0])
1165 cube([400, 800, 50]);
1166 if (enable_support && !$button_suppress_over_keeper)
1168 translate([-400, -400, kppd[1]])
1170 cube([800,800,100]);
1172 translate([0,0, -bppR[0]])
1173 linear_extrude(height= 20)
1174 ButtonPlan($button_l, 1,1);
1179 // apertures along top edge
1180 CaseAperture(jack_pos, jack_dia, 8);
1182 CaseAperture(noisecancelmic_pos, noisecancelmic_dia, 8);
1184 OrdinaryRearApertures();
1188 // gaps for the lid's hinge arms
1189 HingePortion(hex20 - hinge_x_arms_gap,
1190 hex21 + hinge_x_arms_gap)
1193 circle(r= hinge_r_arms_gap, $fn= 8);
1196 // screw holes in the hinge arms
1200 CatchPortion(catch_side_gap*2, epp4[1])
1205 translate([ly_o[0], -(phone_cnr_rad + ly_re), ly_o[1]])
1206 rotate([0, ly_theta, 0])
1208 LanyardCutout(lanyard_channel_len);
1212 translate([prop_x_pos,0,0])
1215 linextr(-prop_recess_hw, +prop_recess_hw)
1217 for (d=[ [0,0], [0,-1], [+1,-1/prop_caserecess_taper] ])
1218 circleat(prcp1 + 20*d,
1224 module LidAdhocMultiprintFrame(phase){
1225 if (led_window_style >= 3) {
1226 AdhocMultiprintFrame(phase, lpp13[1], -1);
1230 module LidAroundEdges(){
1231 AroundEdges(lpp15[1], lpp13[1] - lpp15[1], 0)
1235 module Lid(){ ////toplevel
1236 skew_centre = [0, lpp11[0], lpp11[1]];
1243 translate(skew_centre)
1244 multmatrix([[ 1, 0, 0, 0 ],
1245 [ 0, 1, -lid_fold_clearance_skew, 0 ],
1248 translate(-skew_centre)
1250 LidEdgeFoldClearanceProfile();
1257 translate([0,0,-10])
1258 linear_extrude(height= 20)
1259 ButtonPlan($button_l, 1,0);
1261 translate([0,0,-100])
1262 linear_extrude(height= 200)
1263 ButtonCoverProfile();
1268 HingePortion(hex20, hex21) {
1274 CatchPortion(0, lpp12[1])
1275 CatchCatchProfile();
1277 Struts(lpp10[0] + strut_min_at_end, lpp13[1], -case_th_lid);
1279 // screw holes in the hinge arms
1283 translate([prop_x_pos, -prlp10[0], prlp10[1]])
1286 linextr(-prop_recess_hw, +prop_recess_hw)
1288 for (pa = prop_angles)
1289 PropProfile(pa, 1,1);
1291 // notification led aperture
1292 if (led_window_style)
1293 translate([led_pos[0], -led_pos[1], lpp13[1]]) {
1294 translate([0,0,-10])
1295 cylinder(r=nla_r0, h=20);
1296 if (led_window_style >= 2)
1297 translate([0,0, -nla_t])
1298 cylinder(r=nla_r2, height=20);
1303 LidAdhocMultiprintFrame(1);
1306 module HingeLever(){ ////toplevel
1308 // outer body, positive
1309 HingePortion(hex22, hex22 + phone_width/2)
1310 HingeLeverOuterProfile();
1312 // space for the screws
1313 HingePortion(hex26, hex24)
1314 HingeLeverInnerProfile();
1316 // recesses for the nuts
1317 HingePortion(hex23, hex26+1)
1318 HingeLeverNutProfile();
1320 // bores for the screws
1323 // space for the charging cable
1325 Flip_hinge() MicroUSB();
1329 module LidWindow(){ ////toplevel
1330 translate([led_pos[0], -led_pos[1], lpp13[1]])
1332 cylinder(r= nla_r1, h=nla_t);
1333 LidAdhocMultiprintFrame(0);
1336 module LidWindowPrint(){ ////toplevel
1341 module DemoLidWindowSelect(){
1342 translate([led_pos[0], led_pos[1], -100]) {
1343 translate([0, -30, 0]) cube([400, 400, 200]);
1347 module DemoLidWindow(){ ////toplevel
1350 translate([0,40,0]){
1351 color("blue") intersection(){ Lid(); DemoLidWindowSelect(); }
1352 color("red") intersection(){ LidWindow(); DemoLidWindowSelect(); }
1356 module HingeLeverPrint(){ ////toplevel
1358 translate([-phone_width/2, phone_height, 0])
1362 module TestSelectLength(){
1363 translate([-30, -200, -20])
1364 cube([30 + 15, 250, 40]);
1367 module TestLength(){ ////toplevel
1374 module TestLengthRight(){ ////toplevel
1382 module TestSelectWidth(){
1383 translate([-30, -(phone_height - 25), -20])
1385 cube([200, 50, 40]);
1388 module TestWidth(){ ////toplevel
1395 module TestLidWidthPrint(){ ////toplevel
1396 rotate([0,180.0]) intersection(){
1402 module TestSelectRearAperture(){
1405 translate([20, 0,0])
1406 cube([42, 2, 1], center=true);
1410 module TestSelectCamera(){
1412 TestSelectRearAperture()
1413 RearCameraAperture();
1414 cube([0.1, 50, 0.1]);
1418 module TestSelectOrdinaryRearApertures(){
1419 TestSelectRearAperture()
1420 OrdinaryRearApertures();
1423 module TestCamera(){ ////toplevel
1430 module TestLidByCamera(){ ////toplevel
1437 module TestLidByCameraPrint(){ ////toplevel
1438 rotate([180,0,0]) TestLidByCamera();
1441 module DemoByCamera(){ ////toplevel
1442 color("blue") TestLidByCamera();
1443 color("red") TestCamera();
1446 module OneKeeper(){ ////toplevel
1447 translate([0, -phone_cnr_rad, 0])
1449 linear_extrude(height = phone_height - phone_cnr_rad * 2)
1453 module OneKeeperPrint(){ ////toplevel
1458 module LidPrint(){ ////toplevel
1463 module TestSelectFrame(){
1464 include = [1,-1] * (epp2i[0] + 4);
1467 cube(1000, center=true);
1468 translate([0,0, -100])
1469 linear_extrude(height=200)
1470 rectfromto(include, inside_br - include);
1474 module TestSelectLidFrame(){
1476 translate([led_pos[0], -led_pos[1], -50])
1477 cylinder(r= nla_r2+3, h=100);
1480 module TestFrameCase(){ ////toplevel
1486 TestSelectOrdinaryRearApertures();
1491 module TestSelectTopApertures(){
1492 translate([-100, -35, -100])
1493 cube([400, 100, 200]);
1494 LidAdhocMultiprintFrame(0);
1495 LidAdhocMultiprintFrame(1);
1498 module TestTopApertures(){ ////toplevel
1502 TestSelectTopApertures();
1506 module TestLidTopAperturesPrint(){ ////toplevel
1507 rotate([0,180,0]) intersection(){
1509 TestSelectLidFrame();
1510 TestSelectTopApertures();
1514 module TestLidWindowTopAperturesPrint(){ ////toplevel
1515 rotate([0,180,0]) intersection(){
1517 TestSelectTopApertures();
1521 module TestFrameLidPrint(){ ////toplevel
1522 rotate([0,180,0]) intersection(){
1524 TestSelectLidFrame();
1528 module ButtonPlanForDemo(z, deep, cut){
1530 ButtonPlan(8, deep, cut);
1533 module HingeScrews(){
1534 Flip_rhs() Flip_bot(1){
1535 for (c= [ hppT, hppB ])
1540 translate([0,0,-.2])
1541 cylinder( r= hingescrew_shaft_dia/2,
1542 h = hingescrew_shaft_len+0.2 );
1544 translate([0,0,+.1])
1545 cylinder( r= hingescrew_head_dia/2, h = hingescrew_head_th );
1550 module DemoPropAngleSelect(c){
1551 color(c) difference(){
1552 union(){ children(); }
1553 translate([ prop_x_pos, -400, -200 ])
1554 cube([ 400,800,400 ]);
1558 module DemoPropAngle(ang){
1559 hL = [0, -(phone_height - hppT[0]), hppT[1] - hp_k*2];
1560 hC = [0, -(phone_height - hppB[0]), hppB[1]];
1568 DemoPropAngleSelect("red") Case();
1571 translate([prop_x_pos, -prcp1[0], prcp1[1]])
1572 PropProfileAssignments(ang) {
1574 rotate([-$prp_theta, 0, 0])
1575 translate([0, $prpp1[0], -$prpp1[1]])
1581 translate([0,0, -hp_k*2])
1582 DemoPropAngleSelect("blue")
1586 module DemoPropAngles(){ ////toplevel
1587 for (i=[0 : len(prop_angles)-1])
1588 translate(i * [0, -100, 100])
1589 DemoPropAngle(prop_angles[i]);
1592 module DemoHingeAngle(ang1,ang2){
1593 hL = [0, -(phone_height - hppT[0]), hppT[1]];
1594 hC = [0, -(phone_height - hppB[0]), hppB[1]];
1605 color("blue") intersection(){
1608 translate([bppJ[0], -400, -200])
1610 cube([400, 800, 400]);
1611 translate([10, -400, -200])
1612 cube([10, 800, 400]);
1617 module DemoHingeAngles(){ ////toplevel
1618 angles = [ 0, 4, 8, 12 ];
1619 echo("angles",angles);
1620 for (i=[0 : len(angles)-1]) {
1621 translate(i * [0, 0, 30]) {
1622 DemoHingeAngle(0,angles[i]);
1623 translate([0, 200, 0])
1624 DemoHingeAngle(angles[i],0);
1629 module DemoSelectAdhocLeftRight(right=0) {
1630 translate([phone_width/2, -400, -100]) // , -15, -100 to cross-section
1631 mirror([1-right, 0,0])
1632 cube([400, 800, 200]);
1635 module DemoLeft(){ ////toplevel
1636 color("red") intersection(){ Case(); DemoSelectAdhocLeftRight(); }
1637 color("blue") intersection(){ Lid(); DemoSelectAdhocLeftRight(); }
1640 module DemoFrame(){ ////toplevel
1641 color("red") TestFrameCase();
1642 color("blue") intersection(){ Lid(); TestSelectLidFrame(); }
1643 color("black") HingeScrews();
1647 module DemoLanyardCutout(){ ////toplevel
1651 module DemoHingedFrame(){ ///toplevel
1652 color("red") TestFrameCase();
1653 translate([0,0, -2*hp_k])
1654 color("blue") intersection(){ Lid(); TestSelectLidFrame(); }
1657 color("orange") HingeLever();
1658 color("black") HingeScrews();
1662 module DemoHinge(){ ////toplevel
1663 translate([ -0.5*phone_width, phone_height, hp_k*3 ]) {
1665 translate([0,0, -hp_k*3])
1670 module DemoProfiles(){ ////toplevel
1674 translate([0,0,-1]) color("black") KeeperProfile(1);
1677 translate([0,0,+1]) color("purple") LanyardMainChannelProfile();
1678 translate([0,0,+2]) color("red") LanyardCurveChannelProfile();
1679 translate([0, ly_q_z]){
1680 translate([0,0,-1]) color("blue") LanyardEntryChannelProfile();
1681 translate([ly_oec_y,0,-2]) color("black") LanyardEntryOuterProfile();
1685 translate([0,0,-5]) color("white") translate(epp2i)
1687 rectfromto([-15, 0],
1688 [+15, -max_case_bottom_edge_thickness]);
1691 LanyardMainChannelProfile();
1692 translate([0,0,1]) color("purple") LanyardCurveChannelProfile();
1693 translate([0,0,-1]) color("red") LanyardEntryChannelProfile();
1700 demopoint_QR = [ bppS[0], bppQ[1] - 0.1];
1702 color("blue") ButtonCoverProfile();
1704 rectfromto(bppQ, demopoint_QR);
1705 rectfromto(bppR, demopoint_QR);
1709 translate([-20,0]) {
1710 color("black") ButtonPlanForDemo(-2, 0,1);
1711 color("red" ) ButtonPlanForDemo(-4, 1,1);
1712 color("blue") ButtonPlanForDemo(-6, 1,0);
1715 translate([0, -30]) {
1718 color("blue") HingeLidProfile();
1719 color("red") HingeBaseProfile();
1720 color("black") translate([0,0,-2]) HingeLeverOuterProfile();
1724 translate([-30, -60 + 30*f]) {
1725 translate([0,0,-4]) EdgeProfile();
1726 %translate([0,0,-10]) HingeBaseProfile();
1727 translate([0,-2] * f * hp_k) {
1728 translate([0,0,-4]) LidEdgeProfile();
1729 %translate([0,0,-10]) %HingeLidProfile();
1731 translate(+hppB) rotate([0,0,180*f]) translate(-hppB) {
1732 translate([0,0,-2]) color("black") HingeLeverOuterProfile();
1733 translate([0,0,0]) color("red") difference(){
1734 HingeLeverOuterProfile();
1735 HingeLeverInnerProfile();
1737 translate([0,0,3]) color("yellow") HingeLeverNutProfile();
1742 translate([20,-30]) {
1745 //translate([0,0,1]) CatchCutProfile();
1746 color("blue") CatchCatchProfile();
1747 color("red") difference(){ EdgeProfile(); CatchCutProfile(); }
1750 translate([40,-30]) {
1754 PropProfile(10, 1, 0);
1759 translate([60,-30]) {
1760 PropAggregateProfile();