Import release 0.1.0

[secnet] / INSTALL

INSTALLATION INSTRUCTIONS for SECNET

USE AT YOUR OWN RISK.  THIS IS ALPHA TEST SOFTWARE.  I DO NOT
GUARANTEE THAT THERE WILL BE PROTOCOL COMPATIBILITY BETWEEN DIFFERENT
VERSIONS.

PROTOCOL COMPATIBILITY WAS BROKEN BETWEEN secnet-0.06, secnet-0.07 AND
secnet-0.08 FOR ENDIANNESS FIXES.

THERE WILL BE ANOTHER CHANGE IN PROTOCOL IN THE secnet-0.1.x SERIES

* Preparation

** System software support

Ensure that you have libgmp2-dev and adns installed (and bison and
flex, and for that matter gcc...).

[On BSD install /usr/ports/devel/bison and /usr/ports/devel/libgnugetopt]

If you intend to configure secnet to obtain packets from the kernel
through userv-ipif, install and configure userv-ipif.  It is part of
userv-utils, available from ftp.chiark.greenend.org.uk in
/users/ian/userv

If you intend to configure secnet to obtain packets from the kernel
using the universal TUN/TAP driver, make sure it's configured in your
kernel (it's under "network device support" in Linux-2.4) and that
you've created the appropriate device files; see
linux/Documentation/networking/tuntap.txt

If you're using TUN/TAP on a platform other than Linux-2.4, see
http://vtun.sourceforge.net/tun/

Note than TUN comes in two flavours, one (called 'tun' in the secnet
config file) which has only one device file (usually /dev/net/tun) and
the other (called 'tun-old') which has many device files (/dev/tun*).
Linux-2.4 has new-style TUN, Linux-2.2, BSD and Solaris have old-style
TUN.

** System and network configuration

If you intend to start secnet as root, I suggest you create a userid
for it to run as once it's ready to drop its privileges.  Example (on
Debian):
# adduser --system --no-create-home secnet

You will need to allocate two IP addresses for use by secnet.  One
will be for the tunnel interface on your tunnel endpoint machine (i.e.
the address you see in 'ifconfig' when you look at the tunnel
interface).  The other will be for secnet itself.  These addresses
could possibly be allocated from the range used by your internal
network: if you do this, you should think about providing appropriate
proxy-ARP on the internal network interface of the machine running
secnet (eg. add an entry net/ipv4/conf/eth_whatever/proxy_arp = 1 to
/etc/sysctl.conf on Debian systems and run sysctl -p).  Alternatively
the addresses could be from some other range - this works well if the
machine running secnet is the default route out of your network.

http://www.ucam.org/cam-grin/ may be useful.

* Installation

To install secnet do

$ ./configure
$ make
# make install

(Note: you may see the following warning while compiling
conffile.tab.c; I believe this is a bison bug:
/usr/share/bison/bison.simple: In function `yyparse':
/usr/share/bison/bison.simple:285: warning: `yyval' might be used
 uninitialized in this function
)

Any other warnings or errors should be reported to
steve@greenend.org.uk.

If installing for the first time, do

# mkdir /etc/secnet
# cp example.conf /etc/secnet/secnet.conf
# cd /etc/secnet
# ssh-keygen -f key -N ""

[On BSD use
$ LDFLAGS="-L/usr/local/lib" ./configure
$ gmake CFLAGS="-I/usr/local/include" LDFLAGS="-L/usr/local/lib"
XXX this should eventually be worked out automatically by 'configure'.]

Generate a site file fragment for your site (see below), and submit it
for inclusion in your VPN's 'sites' file.  Download the vpn-sites file
to /etc/secnet/sites - MAKE SURE YOU GET AN AUTHENTIC COPY because the
sites file contains public keys for all the sites in the VPN.

* Configuration

Should be reasonably obvious - edit /etc/secnet/secnet.conf as
prompted by the comments.  XXX Fuller documentation of the
configuration file format should be forthcoming in time.  Its syntax
is described in the README file at the moment.

* Constructing your site file fragment

You need the following information:

1. a short name for your site, eg.  "greenend".  This is used to
identify your site in the vpn-sites file.

2. the name your site will use in the key setup protocol,
eg. "greenend" (these two will usually be similar or the same).

3. the DNS name of the machine that will be the "front-end" for your
secnet installation.  This will typically be the name of the gateway
machine for your network, eg.  sinister.dynamic.greenend.org.uk

secnet does not actually have to run on this machine, as long as the
machine can be configured to forward UDP packets to the machine that
is running secnet.

4. the port number used to contact secnet at your site.  This is the
port number on the front-end machine, and does not necessarily have to
match the port number on the machine running secnet.

5. the list of networks accessible at your site over the VPN.

6. the public part of the RSA key you generated during installation
(in /etc/secnet/key.pub if you followed the installation
instructions).  This file contains three numbers and a comment on one
line.  The first number is the key length in bits, and should be
ignored.  The second number (typically small) is the encryption key
'e', and the third number (large) is the modulus 'n'.

If you are running secnet on a particularly slow machine, you may like
to specify a larger value for the key setup retry timeout than the
default, to prevent unnecessary retransmissions of key setup packets.
See the notes in the example configuration file for more on this.

The site file fragment should look something like this:

shortname {
		name "sitename";
		address "your.public.address.org.uk";
		port 5678;
		networks "172.18.45.0/24";
		key rsa-public("35","153279875126380522437827076871354104097683702803616313419670959273217685015951590424876274370401136371563604396779864283483623325238228723798087715987495590765759771552692972297669972616769731553560605291312242789575053620182470998166393580503400960149506261455420521811814445675652857085993458063584337404329");
	};

See 'example-sites-file' for more examples.