From fc24d245486a02d968985bfbe2c8153c18066b36 Mon Sep 17 00:00:00 2001 From: Ian Jackson Date: Sat, 16 Sep 2023 12:30:11 +0100 Subject: [PATCH] Update Huxley-INSTRUCTIONS to point to old commit. Signed-off-by: Ian Jackson --- Huxley-INSTRUCTIONS | 80 ++------------------------------------------- 1 file changed, 2 insertions(+), 78 deletions(-) diff --git a/Huxley-INSTRUCTIONS b/Huxley-INSTRUCTIONS index c5efa32..45f9b77 100644 --- a/Huxley-INSTRUCTIONS +++ b/Huxley-INSTRUCTIONS @@ -1,79 +1,3 @@ -To prepare file: +Go back to revision e1cdc45 aka "last-with-huxley". - * Make stl file. - openscad -o test-object.tmp.stl test-object.scad - or equivalent. - - * Slice the file. On appropriate OS run Slic3r. - I was using 0.9.7. - Download from here: - http://slic3r.org/download - - Then - - /home/reprap/Slic3r/bin/slic3r --load /home/reprap/play/slic3r-config.ini test-object.stl - - Produces test-object.gcoce. - -To print: - - * Turn on printer and connect computer. - * Start pronterface - cd /home/reprap/reprappro-software.git/ - ./pronterface/pronterface.py - * Select "connect" (make sure it's ttyUSB0 115200), - wait for printer to connect - * Tick "watch" - * Turn on the hotend and bed heaters - * Remove MicroSD card from printer and copy the file to it - (give it an 8.3 filename ending in .G) - * Insert MicroSD card back into printer - * Wait for bed (and hotend) to get up to temperature - * If there's lots of ooze, pick off nozzle with fine-nosed pliers - * "SD" / "Print", select the file you uploaded earlier - * Watch while it starts and make sure that the skirt sticks to - printbed and nothing gets tangled - * Check that filament feed path from feedstock coil looks good. - -After printing: - - * You can right away unclip the bed plate. - * Wait for the object and bed plate to cool before removing it. - -*** DO NOT TURN PRINTER OFF WHILE HOT END IS HOT *** - -Levelling (occasionally, or after transport): - - * Home in pronterface - * Set level: - Use FL/FR to move to front left / right - Use Home Z to make it go up and down - Observe motion of bed - should be just none - Turn RH thread with fingers to adjust so above is true - (Levelling screws front/back are at RH of bed plate.) - -Bed cleaning: use isopropanol - ------------------------------------------------------------- - -make these symlinks -~/.pronsolerc -> /home/reprap/play/pronsolerc (adjust to taste) - -Slic3r - is from slic3r-linux-x86-0-9-7.tar.gz - /home/reprap/Slic3r/bin/slic3r --load /home/reprap/play/slic3r-config.ini --ignore-nonexistent-config - -repsnapper - only used this so far for its gcode viewer - ------------------------------------------------------------- - -firmware upgrade: - - firmware is in marlin.git#iwj and works with make - various other firmwares for comparison only - sprinter-reprappro.git sprinter.git - produces Marlin.hex - depends on stuff in arduino-0022 (doesn't work with other arduino - versions, incompatible) - program with - avrdude -b 38400 -v -P /dev/ttyUSB0 -p atmega644P -c arduino -U flash:w:Marlin.hex - needs the reset jumper (which is right next to the mcu) fitted +The files for our old Huxley have been removed from this tree since then. -- 2.30.2