// -*- C -*-
-main_dia = 71.2 + 0.50;
-top_thick = 4;
+coarse = false;
-main_cnr = 4.0;
+main_dia = 71.2 + 0.50 - 2.26;
+top_thick_middle = 4;
+top_thick_by_oring = 3.0;
+top_middle_dr = 11;
-rivet_posn = 6.0;
+main_cnr = 6.0;
+
+min_wall = 3;
+
+rivet_posn = 6.0 + 0.6;
rivet_thick = 1.67;
rivet_width = 4.15 + 1.0;
-rivet_tall = 5.51 + 0.49;
+rivet_tall = 5.51 + 1.49;
-over_rivet_wall = 0.5;
+over_rivet_wall = 1.0;
side_rivet_gap = 1.5;
+inside_rivet_gap = 1.5;
-bayo_interf = 0.75;
+bayo_interf = 0.85;
bayo_behind = 3.5;
bayo_interf_width = 2.0;
-bayo_interf_slope = 0.75;
+bayo_interf_slope = 0.5;
+
+oring_thick = 5.0;
+oring_bore = 62.0;
+
+oring_upper_embed_angle = 80;
+oring_compress = 0.1; // proportion
-seal_thick = 0.1;
-seal_recess = [ 2.0, 2.0 ]; // recess depth, recess height
+oring_rm_beside = 8;
+oring_rm_scale = 2.0;
+oring_rm_angle = 20;
side_taper = 1.0;
-bayo_above_gap = 1.0;
+bayo_gap = 6.0;
bayo_entry = bayo_behind/3;
-bayo_slice_size = 1;
+bayo_slice_size = coarse ? 5 : 1;
+
+brace_hole_width = 1.0;
+brace_above_below = 1.2;
+brace_end_shorter = 0.3;
+
+jig_thick = 1.4;
+jig_hole_dia = 3.0;
+jig_rim = 5;
+jig_mark = 5;
+
+strap_hoop_thick = 6;
+strap_hoop_inside = 10;
+strap_hoop_strlen = 10;
+strap_hoop_elevation = 45;
// calculated
bayo_inramp_x = bayo_entry;
bayo_inramp_z = bayo_entry;
+oring_mid_dia = oring_bore + oring_thick;
+oring_outer_dia = oring_mid_dia + oring_thick;
+
+oring_oblate = (1 - oring_compress);
+
+oring_y_rad = oring_thick/2 * oring_oblate;
+oring_x_rad = oring_thick/2 / oring_oblate;
+
+by_oring_z = oring_y_rad * (1 + cos(oring_upper_embed_angle));
+
side_height = rivet_posn + bayo_behind + rivet_thick/2;
side_thick = rivet_tall + over_rivet_wall;
-top_z = top_thick + seal_thick;
+top_z = top_thick_by_oring + oring_y_rad + by_oring_z;
+
+middle_bot_z = top_z - top_thick_middle;
bayo_entry = bayo_behind / 3.0;
-bayo_top_z = bayo_behind + rivet_thick + bayo_above_gap;
-bayo_entry_ramp = bayo_entry + bayo_interf;
+bayo_top_z = bayo_behind + bayo_gap;
rivet_entry_width = rivet_width + side_rivet_gap;
-$fs=0.5;
-$fa=1;
+jig_mark_rad = jig_mark + main_dia/2 + jig_thick;
+
+handling_dia = oring_bore + oring_thick*2 + min_wall*2;
+handling_angle = 45;
+
+$fs= coarse ? 2.5 : 0.5;
+$fa= coarse ? 5 : 1;
// bayonet definition
bayo_l = bayo_m + bayo_interf * [ 1/bayo_interf_slope, 1 ];
bayo_k = bayo_l + [ bayo_interf_width, 0 ];
bayo_j = bayo_k + bayo_interf * [ 1/bayo_interf_slope, -1 ];
-bayo_i = bayo_j + [ rivet_width, 0 ];
-bayo_h = [ bayo_i[0], bayo_behind + rivet_thick + bayo_above_gap ];
+bayo_i = bayo_j + [ rivet_width + inside_rivet_gap, 0 ];
+bayo_h = [ bayo_i[0], bayo_behind + bayo_gap + bayo_interf ];
bayo_g = [ bayo_m[0] - rivet_width, bayo_h[1] ];
bayo_e = [-bayo_p[0], bayo_p[1]] - [rivet_entry_width,0];
module MainProfile(){
main_cnr_pos = [ side_thick, top_z ] - [1,1]*main_cnr;
- translate(main_cnr_pos){
- intersection(){
- difference(){
- circle(r = main_cnr);
- circle(r = main_cnr * 0.5);
+ difference(){
+ union(){
+ translate(main_cnr_pos){
+ intersection(){
+ difference(){
+ circle(r = main_cnr);
+ circle(r = main_cnr * 0.5);
+ }
+ square([10,10]);
+ }
+ }
+ polygon([[ -top_middle_dr, middle_bot_z ],
+ [ -top_middle_dr, top_z ],
+ [ main_cnr_pos[0], top_z ],
+ [ side_thick, main_cnr_pos[1] ],
+ [ side_thick, -side_height ],
+ [ side_taper, -side_height ],
+ [ 0, -rivet_posn ],
+ [ 0, by_oring_z ],
+ [ -oring_x_rad, by_oring_z ],
+ ],
+ convexity=10);
+ }
+ translate([ oring_mid_dia/2 - main_dia/2, 0 ])
+ hull(){
+ translate([ 0, oring_y_rad ])
+ scale([ 1/oring_oblate, oring_oblate ])
+ circle(oring_thick/2);
+ translate([ 0, oring_y_rad*2 - oring_thick/2 ])
+ circle(oring_thick/2);
+ }
+ }
+}
+
+module StrapHoopProfile(){
+ circle(r = strap_hoop_thick/2);
+}
+
+module StrapHoop(){ ////toplevel
+ bigrad = strap_hoop_inside/2 + strap_hoop_thick/2;
+ extralen = strap_hoop_thick * 5;
+
+ intersection(){
+ rotate([strap_hoop_elevation, 0,0]){
+ for (x= [ -1, +1 ] * bigrad) {
+ translate([x, -extralen, 0])
+ rotate([-90,0,0])
+ linear_extrude(height= extralen + strap_hoop_strlen + 0.1,
+ convexity=10)
+ StrapHoopProfile();
+ }
+ translate([0, strap_hoop_strlen, 0]){
+ intersection(){
+ rotate_extrude(convexity=10)
+ translate([bigrad, 0,0])
+ StrapHoopProfile();
+ translate([0,50,0])
+ cube([100,100,100], center=true);
+ }
}
- square([10,10]);
}
+ translate([0, 50, 0])
+ cube(100, center=true);
}
- polygon([[ -1, seal_thick ],
- [ -1, top_z ],
- [ main_cnr_pos[0], top_z ],
- [ side_thick, main_cnr_pos[1] ],
- [ side_thick, -side_height ],
- [ side_taper, -side_height ],
- [ 0, -rivet_posn ],
- [ 0, -(seal_recess[0] + seal_recess[1]) ],
- [ seal_recess[0], -(seal_recess[0]) ],
- [ seal_recess[0], seal_thick ],
- ]);
}
-module RotateProjectSlice(offset, poly, slice_size, nom_rad, real_rad){
+module HandlingProfile(){
+// translate([
+}
+
+module RotateProjectSlice(offset, slice_size, nom_rad, real_rad){
// nom_rad > real_rad
rotate([0,0, atan2(offset, nom_rad) ]){
intersection(){
translate([-offset, -10, 0])
rotate([90,0,0])
linear_extrude(height= nom_rad*2)
- polygon(poly);
+ children(0);
translate([0,0, -25])
cylinder(h=50, r= real_rad);
translate([0,0, -25])
}
}
-module RotateProject(poly, x_min, x_max, slice_size, nom_rad, real_rad){
+module RotateProject(x_min, x_max, slice_size, nom_rad, real_rad){
offs = [ for (i=[ x_min :
slice_size :
x_max + slice_size ]) i ];
echo (offs);
for (off=offs)
- RotateProjectSlice(off, poly, slice_size, nom_rad, real_rad);
+ RotateProjectSlice(off, slice_size, nom_rad, real_rad)
+ children(0);
}
module BayonetCutout(){
- RotateProject(bayo_polygon,
- bayo_c[0], bayo_i[0], bayo_slice_size,
+ RotateProject(bayo_c[0], bayo_i[0], bayo_slice_size,
main_dia/2 + side_thick,
- main_dia/2 + rivet_tall);
+ main_dia/2 + rivet_tall)
+ translate([-0.5 * (bayo_a[0] + bayo_d[0]), 0])
+ polygon(bayo_polygon, convexity=10);
+}
+
+module ProfilesDemo(){ ////toplevel
+ translate([-10,0]) MainProfile();
+ translate([+10, -side_height]) polygon(bayo_polygon, convexity=10);
+}
+
+module LimitForHandling(){ ////toplevel
+ hull() for (r=[0,180])
+ rotate([0,0,r]) {
+ for (rs=[-1,+1]) {
+ for (xd=[0,1]) {
+ rotate([0,0, rs * handling_angle/2]) {
+ translate([rs * xd * main_dia/2 * tan(handling_angle/2),
+ main_dia/2 + side_thick - main_cnr,
+ top_z - main_cnr]) {
+ mirror([0,0,1])
+ cylinder(r= main_cnr, h=50);
+ sphere(main_cnr);
+ }
+ }
+ }
+ }
+ }
+ hull() rotate_extrude(){
+ translate([ handling_dia/2 - main_cnr, top_z - main_cnr ]) {
+ circle(r = main_cnr);
+ mirror([0,1]) square([ main_cnr, 50 ]);
+ }
+ }
+ //cylinder(r= handling_dia/2, h=20);
+}
+
+module Cover(){ ////toplevel
+ render() difference(){
+ intersection(){
+ union(){
+ rotate_extrude(convexity=10)
+ translate([main_dia/2, 0])
+ MainProfile();
+ translate([0,0, middle_bot_z])
+ cylinder(h= top_thick_middle, r = main_dia/2 - top_middle_dr + 1);
+ }
+ LimitForHandling();
+ }
+ for (r=[0,180]){
+ rotate([0,0, r])
+ translate([0,0, -side_height])
+ BayonetCutout();
+ rotate([0,0, r + asin((-oring_rm_beside) / (main_dia/2))])
+ translate([0,
+ oring_mid_dia/2 + oring_thick/4 * oring_rm_scale,
+ oring_y_rad * 1.5])
+ rotate([-oring_rm_angle, 0, 0])
+ mirror([0,0,1])
+ cylinder(r = oring_thick/4 * oring_rm_scale, h=20);
+ }
+ for (r=[0 : 60 : 179]) {
+ rotate([0,0, r]) {
+ height = top_thick_middle - brace_above_below*2;
+ translate([0,0, middle_bot_z + brace_above_below + height/2 ])
+ cube(center=true, [ oring_bore - brace_end_shorter,
+ brace_hole_width, height ]);
+ }
+ }
+ }
+ translate(strap_hoop_thick * [-0.5, 0, +1])
+ translate([handling_dia/2, 0, -side_height])
+ rotate([0,180,0]) rotate([0,0,90])
+ StrapHoop();
+}
+
+module SavingHole(){
+ translate([0,0, -10])
+ cylinder(r= main_dia/2 - jig_rim, h=20);
+}
+
+module Jig(){ ////toplevel
+ difference(){
+ union(){
+ translate([0,0, -side_height]){
+ cylinder(r= main_dia/2 + jig_thick, h= side_height + jig_thick);
+ }
+ translate([-jig_mark_rad, 0, jig_thick - jig_mark])
+ cube([jig_mark_rad*2, jig_mark, jig_mark]);
+ }
+ translate([0,0, -side_height-1])
+ cylinder(r= main_dia/2, h= side_height + 1);
+ SavingHole();
+ translate([0,0, -rivet_posn])
+ rotate([90, 0,0])
+ translate([0,0, -100])
+ cylinder(r= jig_hole_dia/2, h = 200);
+ }
+}
+
+module CoverTest2(){ ////toplevel
+ difference(){
+ Cover();
+ SavingHole();
+ }
}
-module ProfilesDemo(){
- translate([-20,0]) MainProfile();
- polygon(bayo_polygon);
+module CoverTest1(){ ////toplevel
+ difference(){
+ CoverTest2();
+ difference(){
+ for (r= [ 40, 147 ]){
+ rotate([0,0, r]){
+ translate([0,0, -10]) {
+ cube([ main_dia*3, main_dia * .55, 18], center=true);
+ }
+ }
+ }
+ translate([ 50, 0, 0 ])
+ cube([ 100,
+ strap_hoop_inside + strap_hoop_thick*2 + 1,
+ 100 ],
+ center=true);
+ }
+ }
}
//ProfilesDemo();
-BayonetCutout();
+//BayonetCutout();
+//MainProfile();
+//Cover();
+//Jig();
+//CoverTest();
~ianmdlvl / reprap-play.git / blobdiff