4 include <commitid.scad>
24 interlock_fine = 0.66;
26 interlock_fine_slope = 1.0;
27 interlock_fine_lenslop = 1.0;
33 machine_rear_to_front = 85;
35 machine_rear_profile = [
51 machine_front_profile = [
66 cutout_l_end_y_front_slop = 0.5;
67 cutout_l_end_y_rear_slop = 0.5;
68 cutout_l_end_x_slop = 0.25;
71 cutout_l_end_y = machine_rear_to_front;
72 cutout_l_end_curve = 1;
73 cutout_l_end_y_total = cutout_l_end_y
74 + cutout_l_end_y_front_slop + cutout_l_end_y_rear_slop;
76 tile02_tr = [-250, 0];
79 cutout_tile01_y = 170 - 147 + cutout_l_end_y_front_slop;
80 cutout_tile11_x = cutout_l_end_x + cutout_l_end_curve;
81 cutout_tile11_y = cutout_l_end_y_total - cutout_tile01_y;
83 // front and rear curves
87 rearcurve_strt_len = 52;
89 rearcurve_z_slop = 0.75;
91 rearcurve_avoid_y = 35;
93 rearcurve_double_inrad = 26.10 + 8.04;
99 frontcurve_side_skew = 3.5 / 72;
100 frontcurve_avoid_y = 70;
101 frontcurve_z_slop = 0.75;
107 ply_edge_hole_dist = ply_edge_min + ply_hole_dia/2;
109 echo(str("HOLES IN PLY ctr dist from PLY edge = ", ply_edge_hole_dist));
111 hole_slop = (ply_hole_dia - post_dia)/2;
112 tile_hard_edge_hole_dist = ply_edge_hole_dist + hole_slop;
114 echo(str("HOLES IN PLY ctr dist from TILE HARD edge = ",
115 tile_hard_edge_hole_dist));
117 echo(str("HOLES IN PLY ctr dist from TILE ROUND edge = ",
118 tile_hard_edge_hole_dist + round_edge_rad));
120 thehd = [ tile_hard_edge_hole_dist, tile_hard_edge_hole_dist ];
122 thehd_tl = [ -thehd_tr[0], thehd_tr[1] ];
123 thehd_bl = -thehd_tr;
124 thehd_br = -thehd_tl;
126 interlock_rad = interlock_dia/2;
127 interlock_negative_rad = interlock_rad + 0.125;
129 interlock_sq_adj = 0.2; // arbitrary
131 first_front = machine_front_profile[len(machine_front_profile)-1];
133 m4_define(`POST_TCROSSSZ',
134 `2*( tile_hard_edge_hole_dist - test_edge + 1 )')
139 cylinder(r= post_dia/2, h= tile_th + ply_th - post_shorter);
140 translate([0,0, tile_th]) {
141 cylinder(r= screw_big_dia/2, h= screw_big_len);
142 cylinder(r= screw_dia/2, h= ply_th, $fn=20);
146 translate([0,0, tile_th/2]) {
147 cube([post_dia, POST_TCROSSSZ, tile_th], center=true);
148 cube([POST_TCROSSSZ, post_dia, tile_th], center=true);
154 module Posts(posts) {
156 translate(concat(p, [0]))
161 module TileBase(botleft, topright){
162 size = topright - botleft;
163 botleft_post = botleft + thehd_tr;
164 topright_post = topright + thehd_bl;
167 translate(concat(botleft, [0]))
168 cube(concat(size, [tile_th]));
170 cidsz = topright_post-botleft_post
171 + [-post_dia,-post_dia]
173 cidszr = [ min(cidsz[0],50), min(cidsz[1],50) ];
174 echo("CID",cidsz,cidszr);
175 translate( concat(botleft_post, [ -tile_th ])
176 + 0.5 * [ post_dia, post_dia, 0 ]
177 + 0.5 * concat( cidsz - cidszr, [ 0 ]) )
178 Commitid_BestCount_M(cidszr);
181 crossoff = tile_hard_edge_hole_dist + POST_TCROSSSZ/2;
182 cidsz = [ thehd[0], size[1] - 2*crossoff ];
183 cidszr = [ cidsz[0], min(cidsz[1], 50) ];
184 translate( concat(botleft + [0, crossoff] + (cidsz-cidszr)/2, [0]) )
185 Commitid_BestCount(cidszr);
188 translate(concat(botleft + [test_edge,test_edge], [test_tile_th]))
189 cube(concat(size - [test_edge,test_edge]*2, [tile_th]));
190 translate(concat(botleft_post, [-1]))
191 cube(concat(topright_post-botleft_post, [tile_th+2]));
195 cube(max(test_edge, tile_hard_edge_hole_dist)*2, center=true);
202 m4_dnl INREFFRAME(left_cnr, right_cnr, morevars) { body; }
203 m4_define(`INREFFRAME',`
204 length_vec = ($2) - ($1);
205 length = dist2d([0,0], length_vec);
206 length_uvec = length_vec / length;
207 ortho_uvec = [ -length_uvec[1], length_uvec[0] ];
208 m = [ [ length_uvec[0], ortho_uvec[0], 0, ($1)[0], ],
209 [ length_uvec[1], ortho_uvec[1], 0, ($1)[1], ],
216 m4_dnl INREFFRAME(left_cnr, right_cnr, morevars)
217 m4_dnl INREFFRAME_EDGE { body; }
218 m4_define(`INREFFRAME_EDGE',`
219 translate([0,0, -round_edge_rad])
222 module RoundEdge(left_cnr, right_cnr) {
223 INREFFRAME(left_cnr, right_cnr)
227 cylinder(r= round_edge_rad, h= length, $fn=50);
228 translate([-1, 0, -20])
229 cube([length+2, 20, 20]);
234 module RoundCornerCut(ci) {
235 // ci should be [this_cnr, right_cnr]
236 // where right_cnr is to the right (ie, anticlockwise)
239 offr= round_cnr_rad - round_edge_rad;
240 INREFFRAME(this_cnr, right_cnr) INREFFRAME_EDGE {
242 cube(offr*2 - 0.1, center=true);
243 translate([offr, offr, 0])
244 cylinder(center=true, h=20, r= offr);
249 module RoundCornerAdd(ci) {
252 bigr = round_cnr_rad - round_edge_rad;
253 INREFFRAME(this_cnr, right_cnr) INREFFRAME_EDGE {
255 cube(bigr*2 + 0.1, center=true);
256 translate([bigr, bigr, 0])
257 rotate_extrude(convexity=10, $fn=50)
260 circle(r= round_edge_rad, $fn=50);
268 module InterlockLobePlan(negative) {
269 r = negative ? interlock_negative_rad : interlock_rad;
270 ymir = negative ? 0 : 1;
274 translate([thehd[0], 0]){
278 translate([-dx, -0.1])
279 square([ dx*2, r/2 + 0.1 ]);
281 translate([ xi*dx, r ])
289 module InterlockEdgePlan(negative, nlobes, length, dosquare=true) {
290 for (lobei = [ 0 : nlobes-1 ]) {
291 lobex = (length - thehd[0]*2) * (lobei ? lobei / (nlobes-1) : 0);
292 translate([lobex, 0, 0]) {
293 InterlockLobePlan(negative);
299 slotshorter = negative ? -0.1 : interlock_fine_lenslop;
300 mirror([0, negative])
301 translate([slotshorter, iadj])
302 square([length - slotshorter*2, interlock_fine + iadj*2]);
306 module InterlockEdge(left_cnr, right_cnr, negative=0, nlobes=2) {
307 plusth = negative * 1.0;
308 protr = interlock_fine + interlock_sq_adj;
311 z1 = -tile_th/2 - protr / interlock_fine_slope;
312 z3 = -tile_th/2 + protr / interlock_fine_slope;
314 negsign = negative ? -1 : +1;
315 yprotr = negsign * protr;
317 INREFFRAME(left_cnr, right_cnr) {
318 for (vsect = [ // zs0 zs1 ys0, ys1
319 [ -tile_th-plusth, plusth, 0, 0],
320 [ z1, z2, 0, yprotr],
321 [ z2, z3, yprotr, 0],
331 [ 0,1, -sl, -ys0 + negsign*interlock_sq_adj ],
335 linear_extrude(height=zsd, convexity=10)
336 InterlockEdgePlan(negative, nlobes, length, !!ysd);
341 function TestPiece_holes2corners(holes) =
342 [ holes[0] + thehd_bl,
345 holes[0] + thehd_tl ];
347 module TestPiece1(){ ////toplevel
351 corners = TestPiece_holes2corners(holes);
352 rcs = [corners[0], corners[1]];
355 TileBase(corners[0], corners[2]);
357 RoundEdge(corners[0], corners[1]);
358 RoundEdge(corners[3], corners[0]);
360 InterlockEdge(corners[1], corners[2], 1, nlobes=1);
366 module TestPiece2(){ ////toplevel
370 corners = TestPiece_holes2corners(holes);
371 TileBase(corners[0], corners[2]);
373 RoundEdge(corners[0], corners[1]);
374 InterlockEdge(corners[3], corners[0], 0, nlobes=1);
377 module TestDemo(){ ////toplevel
378 translate([ -thehd[0], 0 ])
381 translate([ +thehd[0] + demo_slop, 0 ])
385 module Machine_Arm(){
386 ysz = cutout_l_end_y_total;
387 // assume the round end is arc of a circle
388 chordlen = dist2d([0,0], [ cutout_l_end_y, cutout_l_end_curve ]);
389 endrad = cutout_l_end_y / cutout_l_end_curve * chordlen;
391 translate([0,0,-30]) linear_extrude(height=60) {
392 translate(tile01_tr + [0, (-cutout_tile01_y + cutout_tile11_y)/2]) {
394 translate([-50, -ysz/2])
396 translate([ endrad - cutout_tile11_x - cutout_l_end_x_slop, 0 ])
397 circle(r=endrad, $fa=0.01,$fd=5);
403 module Machine_Profile(){
404 first_rear = machine_rear_profile[0];
405 below_point = 0.5 * ( first_rear + first_front ) + [ 0, -10 ];
406 pol = concat( machine_rear_profile,
408 machine_front_profile);
409 skew_angle = atan2( first_front[1] - first_rear[1],
410 first_front[0] - first_rear[0] );
411 echo(below_point, pol, skew_angle);
416 rotate([0,0, -skew_angle ]){
417 //translate( - first_front )
425 module Machine_NewRearProfile(){
426 // figures copied out of xfig edit boxes
427 // best not to edit the posbox size if poss - just move it
428 posbox = 10 * ([7.2333,-14.1267] - [-16.2289,40.0289]); // box, Green
429 sideline = -10 * ([-6.2400,13.5600] - [-2.4467,28.2556]); // line, Blue
430 scaleline = 10 * dist2d([-1.1911,-20.4800], [-11.2600,4.0578]); // Green2
431 scaleline_mm = 12+5+10+5+3;
432 sh = -[abs(posbox[0]), abs(posbox[1])];
433 rot = atan2(-sideline[0], sideline[1]);
434 sc = scaleline_mm / scaleline;
435 echo("SH",sh,rot,sc);
436 scale(sc) rotate(rot) translate(sh){
437 import("sewing-table-rear-profile.dxf", convexity=10); // spline, Pink3
441 module Machine_NewRearCurve(){
442 slant = atan2(4,210-10);
444 translate([0,0, rearcurve_double_inrad]) rotate([slant,0,0]){
445 translate([ rearcurve_double_inrad,
447 -rearcurve_double_inrad + 10 ]){
448 rotate([180,0,0]) rotate([0,0,90]) linear_extrude(height=30){
450 Machine_NewRearProfile();
451 translate([0,-100]) Machine_NewRearProfile();
455 rotate([0,90,0]) rotate([90,0,0]) {
457 rotate_extrude(convexity=10, $fn=64)
459 translate([ 0, -rearcurve_double_inrad ])
460 Machine_NewRearProfile();
461 translate([0,0,-500])
462 cube([500,500,1000]);
465 translate([1,0,-rearcurve_double_inrad])
466 rotate([0,-90,0]) rotate([0,0,-90])
467 linear_extrude(height= rearcurve_strt_len + 1)
468 Machine_NewRearProfile();
472 module Machine_RearProfile(){ ////toplevel
475 translate([ -200 + machine_rear_to_front/2, -100 ]) {
481 module Machine_FrontProfile(){
484 translate([ machine_rear_to_front/2, -100 ]) {
490 module Machine_Curves(){ ////toplevel
491 translate([ tile01_tr[0] - cutout_l_end_x + rearedge_len,
495 translate([ -reartablet_x,
499 cube([ reartablet_x+1,
503 translate([ tile01_tr[0] - cutout_l_end_x + rearedge_len,
505 frontcurve_z_slop ]){
506 translate([ 0, -first_front[0] , 0 ])
507 multmatrix([[1, -frontcurve_side_skew, 0, 0],
511 translate([ 0, first_front[0] , 0 ])
513 rotate([0,-90,0])rotate([0,0,-90]){
514 linear_extrude(height= 200)
515 Machine_FrontProfile();
518 translate([ rearcurve_strt_len,
521 Machine_NewRearCurve();
526 module Machine(){ ////toplevel
531 function Rectangle_corners(c0, sz) =
532 // returns the corners of a rectangle from c0 to c0+sz
533 // if sz is positive, the corners are anticlockwise starting with c0
536 c0 + [ sz[0], sz[1] ],
539 function Rectangle_corners2posts(c) =
545 module Rectangle_TileBase(c) { TileBase(c[0], c[2]); }
547 function Posts_interpolate_one(c0,c1) = [c0, (c0+c1)/2, c1];
550 m4_dnl c is from Rectangle_corners and
551 m4_dnl ix is a corner number
552 m4_dnl expands to two comma-separated corners:
553 m4_dnl that denoted by ix, and the next one anticlockwise
554 m4_define(`R_EDGE',`$1[$2],$1[(($2)+1)%4]')
556 module FitTest_general(c0,sz){
557 c = Rectangle_corners(c0, sz);
561 Rectangle_TileBase(c);
562 translate(concat(c0, [-brace[2] + 0.1])){
564 cube(concat(sz,[brace[2]]) - [5,0,0]);
565 translate(brace + [0,0, -25])
566 cube(concat(sz, [50]) - brace*2 + [10,0,0]);
569 RoundEdge(R_EDGE(c,1));
575 module FitTest_Entire(){ ////toplevel
576 FitTest_general([-40,-80], [275,180]);
579 module FitTest_RearCurve(){ ////toplevel
580 FitTest_general([110,0], [170,100]);
583 module FitTest_FrontCurve(){ ////toplevel
584 FitTest_general([110,-80], [170,80]);
587 module Tile02(){ ////toplevel
589 c0 = tile02_tr + -sz;
590 c = Rectangle_corners(c0, sz);
591 posts = Rectangle_corners2posts(c);
595 Rectangle_TileBase(c);
597 RoundEdge(R_EDGE(c,0));
598 RoundEdge(R_EDGE(c,3));
599 InterlockEdge(R_EDGE(c,2), 0);
601 InterlockEdge(R_EDGE(c,1), 1);
607 module Tile12(){ ////toplevel
609 c0 = tile02_tr + [-sz[0], 0];
610 c = Rectangle_corners(c0, sz);
611 posts = Rectangle_corners2posts(c);
615 Rectangle_TileBase(c);
617 RoundEdge(R_EDGE(c,2));
618 RoundEdge(R_EDGE(c,3));
620 InterlockEdge(R_EDGE(c,0), 1);
621 InterlockEdge(R_EDGE(c,1), 1);
627 tile_01_11_cnr = tile01_tr + [-cutout_tile11_x, 0];
628 tile_11_10_cnr = tile01_tr + [0, cutout_tile11_y];
629 tile_01_00_cnr = tile01_tr - [0, cutout_tile01_y];
631 module Tile11(){ ////toplevel
633 c0 = tile01_tr + [-sz[0],0];
634 c = Rectangle_corners(c0, sz);
635 cnr_posts = Rectangle_corners2posts(c);
637 Posts_interpolate_one(cnr_posts[0],
638 cnr_posts[1] - [cutout_tile11_x, 0]),
639 [ cnr_posts[1] + [0, cutout_tile11_y],
645 Rectangle_TileBase(c);
647 RoundEdge(R_EDGE(c,2));
648 InterlockEdge(R_EDGE(c,3));
650 InterlockEdge(c[0], tile_01_11_cnr, 1);
651 InterlockEdge(tile_11_10_cnr, c[2], 1);
656 module Tile01(){ ////toplevel
658 c0 = tile01_tr + -sz;
659 c = Rectangle_corners(c0, sz);
660 cnr_posts = Rectangle_corners2posts(c);
662 Posts_interpolate_one(R_EDGE(cnr_posts,0)),
663 [ cnr_posts[2] + [0, -cutout_tile01_y] ],
664 Posts_interpolate_one(cnr_posts[2] - [cutout_tile11_x, 0],
669 Rectangle_TileBase(c);
671 RoundEdge(R_EDGE(c,0));
672 InterlockEdge(tile_01_11_cnr, c[3]);
673 InterlockEdge(R_EDGE(c,3));
675 InterlockEdge(c[1], tile_01_00_cnr, 1);
680 module Tile10(){ ////toplevel
682 c0 = tile01_tr + [0,0];
683 c = Rectangle_corners(c0, sz);
684 cnr_posts = Rectangle_corners2posts(c);
685 cty = cutout_tile11_y;
686 rcy = cty + rearcurve_avoid_y;
687 posts = [ cnr_posts[0] + [ 0, cty ],
688 cnr_posts[1] + [ -sz[0] + rearedge_len - cutout_l_end_x, cty ],
689 cnr_posts[1] + [ 0, rcy ],
695 Rectangle_TileBase(c);
697 RoundEdge(R_EDGE(c,1));
698 RoundEdge(R_EDGE(c,2));
699 InterlockEdge(c[3], tile_11_10_cnr);
707 module Tile00(){ ////toplevel
709 c0 = tile01_tr + [0,-sz[1]];
710 c = Rectangle_corners(c0, sz);
711 cnr_posts = Rectangle_corners2posts(c);
712 cty = cutout_tile01_y;
713 rcy = cty + frontcurve_avoid_y;
714 posts = [ cnr_posts[0],
716 cnr_posts[2] + [ 0, -rcy ],
717 cnr_posts[2] + [ -sz[0] + rearedge_len - cutout_l_end_x, -cty ],
718 cnr_posts[3] + [ 0, -cty ]
723 Rectangle_TileBase(c);
725 RoundEdge(R_EDGE(c,0));
726 RoundEdge(R_EDGE(c,1));
727 InterlockEdge(tile_01_00_cnr, c[0]);
735 module Demo(){ ////toplevel
736 translate(demo_slop*[-2,1]) color("blue") Tile12();
737 translate(demo_slop*[-2,0]) color("red") Tile02();
738 translate(demo_slop*[-2,1]) color("orange") Tile11();
739 translate(demo_slop*[-2,0]) color("purple") Tile01();
740 translate(demo_slop*[-3,1]) color("blue") Tile10();
741 translate(demo_slop*[-3,0]) color("red") Tile00();
750 //Machine_NewRearProfile();
751 //Machine_NewRearCurve();