poster-tube-lid.scad

   1 // -*- C -*-
   2
   3 include <funcs.scad>
   4
   5 coarse = false;
   6
   7 main_dia = 71.2 + 0.50 - 2.26;
   8 top_thick_middle = 4;
   9 top_thick_by_oring = 3.0;
  10 top_middle_dr = 11;
  11
  12 main_cnr = 6.0;
  13
  14 min_wall = 3;
  15
  16 rivet_posn = 6.0 + 0.30;
  17 rivet_thick = 1.67;
  18 rivet_width = 4.15 + 1.0;
  19 rivet_tall = 5.51 + 1.49;
  20
  21 over_rivet_wall = 1.0;
  22 side_rivet_gap = 1.5;
  23 inside_rivet_gap = 1.5;
  24
  25 bayo_interf = 0.30;
  26 bayo_behind = 3.5;
  27 bayo_interf_width = 2.0;
  28 bayo_interf_slope = 0.5;
  29
  30 oring_thick = 5.0;
  31 oring_bore = 62.0;
  32
  33 oring_upper_embed_angle = 80;
  34 oring_compress = 0.1; // proportion
  35 oring_compress_more = 0.2;
  36
  37 oring_rm_beside = 8;
  38 oring_rm_scale = 2.0;
  39 oring_rm_angle = 20;
  40
  41 side_taper = 1.0;
  42
  43 bayo_gap = 6.0;
  44
  45 bayo_entry = bayo_behind/3;
  46
  47 bayo_slice_size = coarse ? 5 : 1;
  48
  49 brace_hole_width = 1.0;
  50 brace_above_below = 1.2;
  51 brace_end_shorter = 0.3;
  52
  53 jig_thick = 1.4;
  54 jig_hole_dia = 3.0;
  55 jig_rim = 5;
  56 jig_mark = 5;
  57
  58 strap_hoop_thick = 6;
  59 strap_hoop_inside = 10;
  60 strap_hoop_strlen = 10;
  61 strap_hoop_elevation = 45;
  62
  63 sm_inner_circum = 218 - 1.90 - 1.00 - 0.50;
  64 sm_main_thick = 2.0;
  65 sm_main_width = 20;
  66
  67 sm_bolt_dia = 3.5 + 0.1;
  68 sm_bolt_shaft = 21.9;
  69 sm_bolt_head_dia = 6.94 + 1.0;
  70 sm_bolt_head_thick = 2.14;
  71 sm_bolt_nut_width = 5.89 + 0.25;
  72 sm_bolt_nut_thick = 3.68;
  73 sm_bolt_tighten_allow = 2.0;
  74
  75 sm_bolt_y_clear = 0.75;
  76 sm_bolt_y_over = 0.5;
  77
  78 sm_closure_cnr = 3.0;
  79
  80 catch_stalk_h = 3;
  81 catch_stalk_len = 50;
  82 catch_head_th = 3;
  83
  84 catch_pin_slop = 0.25; // each side, and above
  85 catch_pin_slop_x_extra = 0.0; // only on one side
  86 catch_stalk_above_gap = 1.5;
  87 catch_stalk_eff_bend_rad = catch_stalk_len * 0.75;
  88
  89 catch_stalk_base_width = 15;
  90
  91 catch_knob_dia = 6;
  92 catch_knob_above_gap = 5;
  93 catch_knob_height = 5;
  94
  95 catch_stalk_below_gap = 1.0;
  96 catch_stalk_beside_gap = 2.0;
  97
  98 // calculated
  99
 100 TAU = PI*2;
 101
 102 bayo_entry_x = bayo_entry;
 103 bayo_entry_z = bayo_entry;
 104 bayo_inramp_x = bayo_entry;
 105 bayo_inramp_z = bayo_entry;
 106
 107 oring_mid_dia = oring_bore + oring_thick;
 108 oring_outer_dia = oring_mid_dia + oring_thick;
 109
 110 oring_oblate = (1 - oring_compress);
 111
 112 oring_y_rad = oring_thick/2 * oring_oblate;
 113 oring_x_rad = oring_thick/2 / oring_oblate;
 114
 115 by_oring_z = oring_y_rad * (1 + cos(oring_upper_embed_angle));
 116
 117 side_height = rivet_posn + bayo_behind + rivet_thick/2;
 118 side_thick = rivet_tall + over_rivet_wall;
 119
 120 top_z = top_thick_by_oring + oring_y_rad + by_oring_z;
 121
 122 middle_bot_z = top_z - top_thick_middle;
 123
 124 bayo_entry = bayo_behind / 3.0;
 125 bayo_top_z = bayo_behind + bayo_gap;
 126
 127 bayo_nom_rad = main_dia/2 + side_thick;
 128 bayo_real_rad = main_dia/2 + rivet_tall;
 129
 130 rivet_entry_width = rivet_width + side_rivet_gap;
 131
 132 jig_mark_rad = jig_mark + main_dia/2 + jig_thick;
 133
 134 handling_dia = oring_bore + oring_thick*2 + min_wall*2;
 135 handling_angle = 45;
 136
 137 sm_inner_rad = (sm_inner_circum + sm_bolt_tighten_allow/2) / TAU;
 138 sm_outer_rad = sm_inner_rad + sm_main_thick;
 139
 140 smc_pos = [ 0, sm_inner_rad, 0 ];
 141
 142 smc_bolt_nut_dia = sm_bolt_nut_width / cos(30);
 143 smc_bolt_nut_eff_thick = sm_bolt_nut_thick + sm_bolt_tighten_allow;
 144
 145 smc_bolt_y = sm_bolt_dia/2 + sm_bolt_y_clear;
 146 smc_max_y = smc_bolt_y + sm_bolt_y_over
 147   + max(sm_bolt_head_dia/2, smc_bolt_nut_dia/2);
 148 smc_cnr_c_x = sm_bolt_shaft/2 - sm_closure_cnr
 149   + sm_bolt_head_thick/2 + smc_bolt_nut_eff_thick/2;
 150
 151 catch_cr = catch_knob_dia/2 + catch_stalk_beside_gap;
 152 catch_strap_width = sm_main_width;
 153 catch_strap_thick = sm_main_thick;
 154
 155 echo("R ", sm_inner_rad, bayo_real_rad, bayo_nom_rad);
 156
 157 $fs= coarse ? 2.5 : 0.5;
 158 $fa= coarse ? 5 : 1;
 159
 160 include <poster-tube-lid-parametric.scad>
 161
 162 // bayonet definition
 163
 164 bayo_a = [ bayo_entry_x, 0 ];
 165 bayo_p = [ 0, bayo_entry_z ];
 166 bayo_n = [ 0, bayo_behind-bayo_inramp_z ];
 167 bayo_m = [ bayo_inramp_x, bayo_behind ];
 168 bayo_l = bayo_m + bayo_interf * [ 1/bayo_interf_slope,  1 ];
 169 bayo_k = bayo_l + [ bayo_interf_width, 0 ];
 170 bayo_j = bayo_k + bayo_interf * [ 1/bayo_interf_slope, -1 ];
 171 bayo_i = bayo_j + [ rivet_width + inside_rivet_gap, 0 ];
 172 bayo_h = [ bayo_i[0], bayo_behind + bayo_gap + bayo_interf ];
 173 bayo_g = [ bayo_m[0] - rivet_width, bayo_h[1] ];
 174
 175 bayo_e = [-bayo_p[0], bayo_p[1]] - [rivet_entry_width,0];
 176 bayo_d = [-bayo_a[0], bayo_a[1]] - [rivet_entry_width,0];
 177 bayo_c = bayo_d + [0,-5];
 178 bayo_b = bayo_a + [0,-5];
 179
 180 bayo_f = [ bayo_e[0], bayo_g[1] + (bayo_e[0] - bayo_g[0]) ];
 181
 182 bayo_polygon = [ bayo_a,
 183                  bayo_b,
 184                  bayo_c,
 185                  bayo_d,
 186                  bayo_e,
 187                  bayo_f,
 188                  bayo_g,
 189                  bayo_h,
 190                  bayo_i,
 191                  bayo_j,
 192                  bayo_k,
 193                  bayo_l,
 194                  bayo_m,
 195                  bayo_n,
 196                  bayo_p ];
 197
 198 echo(bayo_polygon);
 199
 200 // CATCH
 201
 202 //cppy6 = -catch_strap_width * 2/3;
 203
 204 cppxC = 0.41 * sm_inner_rad * TAU;
 205
 206 // catch pin
 207
 208 cpp_adj = (bayo_n[0] - bayo_f[0]) * (1 - sm_inner_rad / bayo_nom_rad);
 209 // radius scaling due to nom and actual radius difference in
 210 // bayo entry construction
 211
 212 cppa = bayo_f + [1,-1] * catch_pin_slop + [1,0] * cpp_adj;
 213 cppb = bayo_g + [1,-1] * catch_pin_slop + [1,0] * cpp_adj;
 214 cppd = [ bayo_n[0]
 215          - catch_pin_slop - catch_pin_slop_x_extra,
 216          -catch_stalk_above_gap ];
 217 cppc = [ cppd[0], cppb[1] ];
 218 cpph = cppd + [0,-1] * catch_stalk_h;
 219 cppe = cppd + [0,-1] * (catch_knob_above_gap + catch_knob_dia/2);
 220 cppf = [ cppa[0], cppe[1] ];
 221 cppg = [ cppa[0], cpph[1] ];
 222 cppB = 0.5 * (cppf + cppe);
 223
 224 echo("RR", sm_inner_rad / bayo_nom_rad);
 225
 226 // catch assembly depression below pin
 227
 228 cppy6 = cppB[1] - (catch_knob_dia/2
 229                    + (cppc[1] - cppd[1])
 230                    + catch_stalk_below_gap);
 231 cpp7 = [ cppB[0], cppy6 + catch_cr ];
 232 cpp11 = cpp7 + [1,0] * catch_cr;
 233 cppy9 = cppy6 + catch_strap_width * 1/3;
 234 cpp9 = [ cpp7[0] + catch_cr * 2, cppy9 ];
 235 cpp8 = cpp9 + [0,-1] * catch_cr;
 236 cpp10 = cpp8 + [-1,0] * catch_cr;
 237 cppC = [ cppxC, cpp9[1] ];
 238 cppD = cppC + [0,-1] * catch_strap_width;
 239
 240 // catch assembly stalk and so on
 241
 242 cppF = [ cppg[0] - catch_stalk_eff_bend_rad, cppd[1] ];
 243 cpp4 = [ cppg[0] - catch_stalk_len, cpph[1] ] + [1,-1] * catch_cr;
 244 cpp5 = [ cpp4[0], cppC[1] + catch_cr ];
 245 cpp2 = cpp5 + [-1,0] * (catch_cr * 2 + catch_stalk_base_width);
 246 cpp2r = cpp2 + [1,0] * catch_cr;
 247 cpp2d = cpp2 + [0,-1] * catch_cr;
 248 cpp3 = [ cpp2[0] + catch_cr * 2, cppd[1] - catch_cr ];
 249 cppA = [ -cppxC, cpp9[1] ];
 250 cppE = [ cppA[0], cppD[1] ];
 251
 252 catch_assembly_dy = -cppy9 + catch_strap_width;
 253
 254
 255 module MainProfile(){
 256   main_cnr_pos = [ side_thick, top_z ] - [1,1]*main_cnr;
 257   difference(){
 258     union(){
 259       translate(main_cnr_pos){
 260         intersection(){
 261           difference(){
 262             circle(r = main_cnr);
 263             circle(r = main_cnr * 0.5);
 264           }
 265           square([10,10]);
 266         }
 267       }
 268       polygon([[ -top_middle_dr,        middle_bot_z      ],
 269                [ -top_middle_dr,        top_z             ],
 270                [ main_cnr_pos[0],       top_z             ],
 271                [ side_thick,            main_cnr_pos[1]   ],
 272                [ side_thick,            -side_height      ],
 273                [ side_taper,            -side_height      ],
 274                [ 0,                     -rivet_posn       ],
 275                [ 0,                     by_oring_z        ],
 276                [ -oring_x_rad,          by_oring_z        ],
 277                ],
 278               convexity=10);
 279     }
 280     translate([ oring_mid_dia/2 - main_dia/2, 0 ])
 281       hull(){
 282       translate([ 0, oring_y_rad ])
 283         scale([ 1/oring_oblate * (oring_compress_more+1) , oring_oblate ])
 284         circle(oring_thick/2);
 285       translate([ 0, oring_y_rad*2 - oring_thick/2 ])
 286         circle(oring_thick/2);
 287     }
 288   }
 289 }
 290
 291 module StrapHoopProfile(){
 292   circle(r = strap_hoop_thick/2);
 293 }
 294
 295 module StrapHoop(){ ////toplevel
 296   bigrad = strap_hoop_inside/2 + strap_hoop_thick/2;
 297   extralen = strap_hoop_thick * 5;
 298
 299   intersection(){
 300     rotate([strap_hoop_elevation, 0,0]){
 301       for (x= [ -1, +1 ] * bigrad) {
 302         translate([x, -extralen, 0])
 303           rotate([-90,0,0])
 304           linear_extrude(height= extralen + strap_hoop_strlen + 0.1,
 305                          convexity=10)
 306           StrapHoopProfile();
 307       }
 308       translate([0, strap_hoop_strlen, 0]){
 309         intersection(){
 310           rotate_extrude(convexity=10)
 311             translate([bigrad, 0,0])
 312             StrapHoopProfile();
 313           translate([0,50,0])
 314             cube([100,100,100], center=true);
 315         }
 316       }
 317     }
 318     translate([0, 50, 0])
 319       cube(100, center=true);
 320   }
 321 }
 322
 323 module RotateProjectSlice(offset, slice_size, nom_rad, real_rad){
 324   // nom_rad > real_rad
 325   rotate([0,0, atan2(offset, nom_rad) ]){
 326     intersection(){
 327       translate([-offset, -10, 0])
 328         rotate([90,0,0])
 329         linear_extrude(height= nom_rad*2)
 330         children(0);
 331       translate([0,0, -25])
 332         cylinder(h=50, r= real_rad);
 333       translate([0,0, -25])
 334         linear_extrude(height= 50)
 335         polygon([ [ 0,0 ],
 336                   [ -slice_size, -real_rad*2 ],
 337                   [ +slice_size, -real_rad*2 ] ]);
 338     }
 339   }
 340 }
 341
 342 module RotateProject(x_min, x_max, slice_size, nom_rad, real_rad){
 343   offs = [ for (i=[ x_min :
 344                     slice_size :
 345                     x_max + slice_size ]) i ];
 346   echo (offs);
 347   for (off=offs)
 348     RotateProjectSlice(off, slice_size, nom_rad, real_rad)
 349     children(0);
 350 }
 351
 352 module BayonetCutout(){
 353   RotateProject(bayo_c[0], bayo_i[0], bayo_slice_size,
 354                 bayo_nom_rad,
 355                 bayo_real_rad)
 356     translate([-0.5 * (bayo_a[0] + bayo_d[0]), 0])
 357     polygon(bayo_polygon, convexity=10);
 358 }
 359
 360 module ProfilesDemo(){ ////toplevel
 361   translate([-10,0]) MainProfile();
 362   translate([+10, -side_height]) polygon(bayo_polygon, convexity=10);
 363 }
 364
 365 module LimitForHandling(){ ////toplevel
 366   hull() for (r=[0,180])
 367     rotate([0,0,r]) {
 368       for (rs=[-1,+1]) {
 369         for (xd=[0,1]) {
 370           rotate([0,0, rs * handling_angle/2]) {
 371             translate([rs * xd * main_dia/2 * tan(handling_angle/2),
 372                        main_dia/2 + side_thick - main_cnr,
 373                        top_z - main_cnr]) {
 374               mirror([0,0,1])
 375                 cylinder(r= main_cnr, h=50);
 376               sphere(main_cnr);
 377             }
 378           }
 379         }
 380       }
 381     }
 382   hull() rotate_extrude(){
 383     translate([ handling_dia/2 - main_cnr, top_z - main_cnr ]) {
 384       circle(r = main_cnr);
 385       mirror([0,1]) square([ main_cnr, 50 ]);
 386     }
 387   }
 388   //cylinder(r= handling_dia/2, h=20);
 389 }
 390
 391 module Cover(){ ////toplevel
 392   render() difference(){
 393     intersection(){
 394       union(){
 395         rotate_extrude(convexity=10)
 396           translate([main_dia/2, 0])
 397           MainProfile();
 398         translate([0,0, middle_bot_z])
 399           cylinder(h= top_thick_middle, r = main_dia/2 - top_middle_dr + 1);
 400       }
 401       LimitForHandling();
 402     }
 403     for (r=[0,180]){
 404       rotate([0,0, r])
 405         translate([0,0, -side_height])
 406         BayonetCutout();
 407       rotate([0,0, r + asin((-oring_rm_beside) / (main_dia/2))])
 408         translate([0,
 409                    oring_mid_dia/2 + oring_thick/4 * oring_rm_scale,
 410                    oring_y_rad * 1.5])
 411         rotate([-oring_rm_angle, 0, 0])
 412         mirror([0,0,1])
 413         cylinder(r = oring_thick/4 * oring_rm_scale, h=20);
 414     }
 415     for (r=[0 : 60 : 179]) {
 416       rotate([0,0, r]) {
 417         height = top_thick_middle - brace_above_below*2;
 418         translate([0,0, middle_bot_z + brace_above_below + height/2 ])
 419         cube(center=true, [ oring_bore - brace_end_shorter,
 420                             brace_hole_width, height ]);
 421       }
 422     }
 423   }
 424   for (r=[0,180])
 425     rotate([0,0,r])
 426       translate([-implheadcup_large_dia * .5 - implheadcup_thick/2,
 427                  -implheadcup_large_dia * .0,
 428                  middle_bot_z + 0.1])
 429       ImplHeadCup();
 430 //  translate(strap_hoop_thick * [-0.5, 0, +1])
 431 //    translate([handling_dia/2, 0, -side_height])
 432 //    rotate([0,180,0]) rotate([0,0,90])
 433 //    StrapHoop();
 434 }
 435
 436 module SavingHole(){
 437   translate([0,0, -10])
 438     cylinder(r= main_dia/2 - jig_rim, h=20);
 439 }
 440
 441 module Jig(){ ////toplevel
 442   difference(){
 443     union(){
 444       translate([0,0, -side_height]){
 445         cylinder(r= main_dia/2 + jig_thick, h= side_height + jig_thick);
 446       }
 447       translate([-jig_mark_rad, 0, jig_thick - jig_mark])
 448         cube([jig_mark_rad*2, jig_mark, jig_mark]);
 449     }
 450     translate([0,0, -side_height-1])
 451       cylinder(r= main_dia/2, h= side_height + 1);
 452     SavingHole();
 453     translate([0,0, -rivet_posn])
 454       rotate([90, 0,0])
 455       translate([0,0, -100])
 456       cylinder(r= jig_hole_dia/2, h = 200);
 457   }
 458 }
 459
 460 module CoverTest2(){ ////toplevel
 461   difference(){
 462     Cover();
 463     SavingHole();
 464   }
 465 }
 466
 467 module CoverTest1(){ ////toplevel
 468   difference(){
 469     CoverTest2();
 470     difference(){
 471       for (r= [ 40, 147 ]){
 472         rotate([0,0, r]){
 473           translate([0,0, -10]) {
 474             cube([ main_dia*3, main_dia * .53, 18], center=true);
 475           }
 476         }
 477       }
 478 //      translate([ 50, 0, 0 ])
 479 //      cube([ 100,
 480 //             strap_hoop_inside + strap_hoop_thick*2 + 1,
 481 //             100 ],
 482 //           center=true);
 483     }
 484   }
 485 }
 486
 487 module ImplHeadCupTest(){ ////toplevel
 488   for (r=[0,180])
 489     rotate([0,0,r])
 490       translate([-17,0,0])
 491       ImplHeadCup();
 492 }
 493
 494 module SomeStrap(){
 495   // children(0) is to add, (1) subtract
 496   difference(){
 497     union(){
 498       cylinder(r=sm_outer_rad, h=sm_main_width);
 499       StrapMountProtrusion(smc_cnr_c_x + sm_closure_cnr,
 500                            smc_max_y,
 501                            sm_closure_cnr);
 502       children(0);
 503     }
 504     translate([0,0,-1])
 505       cylinder(r=sm_inner_rad, h=sm_main_width+2);
 506     translate(smc_pos)
 507       StrapMountBolt(10);
 508     translate(smc_pos)
 509       cube([ sm_bolt_tighten_allow, 40,100 ], center=true);
 510     children(1);
 511   }
 512 }
 513
 514 module StrapMountBolt(l_delta){ ///toplevel
 515   // positioned relative to smc_pos
 516   translate([(smc_bolt_nut_eff_thick - sm_bolt_head_thick)/2,
 517              smc_bolt_y,
 518              sm_main_width/2]){
 519     translate([ -sm_bolt_shaft/2-1, 0,0 ]){
 520       rotate([0,90,0]) cylinder(r= sm_bolt_dia/2, h= sm_bolt_shaft+2);
 521     }
 522     translate([ -sm_bolt_shaft/2, 0,0 ])
 523       rotate([0,-90,0])
 524       cylinder($fn=6, r=smc_bolt_nut_dia/2,
 525                h=smc_bolt_nut_eff_thick + l_delta);
 526     translate([ sm_bolt_shaft/2, 0,0 ])
 527       rotate([0,90,0])
 528       cylinder(r=sm_bolt_head_dia/2, h=sm_bolt_head_thick + l_delta);
 529   }
 530 }
 531
 532 module StrapMountProtrusion(half_x, max_y, cnr){
 533   translate(smc_pos){
 534     linear_extrude(height=sm_main_width, convexity=10){
 535       hull(){
 536         for (m = [0,1]) mirror([m,0,0]) {
 537           translate([-(half_x - cnr), max_y - cnr])
 538             circle(r=cnr);
 539           translate([-half_x, -sm_inner_rad])
 540             square([1,1]);
 541         }
 542       }
 543     }
 544   }
 545 }
 546
 547 module StrapMount(){ ////toplevel
 548   SomeStrap(){
 549     rotate([0,0,180]){
 550       StrapMountProtrusion(strap_hoop_inside/2 + strap_hoop_thick,
 551                            strap_hoop_thick,
 552                            sm_closure_cnr);
 553       translate(smc_pos +
 554                 [0,0, sm_main_width] +
 555                 strap_hoop_thick * [ 0, 0.5, -1.0 ])
 556         StrapHoop();
 557     }
 558     union(){ };
 559   }
 560 }
 561
 562 module CatchAssemblyCoreProfile(){
 563   difference(){
 564     union(){
 565       hull(){
 566         translate(cpp3) circle(r= catch_cr);
 567         polygon([ cpp3,
 568                   cpp2r,
 569                   cpp5,
 570                   cpph,
 571                   cppd
 572                   ]);
 573       }
 574       polygon([cppD,
 575                cppC,
 576                cpp9,
 577                cpp10,
 578                cpp11,
 579                cpp4,
 580                cpp2r,
 581                cpp2d,
 582                cppA,
 583                cppE
 584                ]);
 585       translate(cpp8) circle(r= catch_cr);
 586     }
 587     hull(){
 588       translate(cpp4) circle(r= catch_cr);
 589       translate(cpp5) circle(r= catch_cr);
 590       translate(cpp7) circle(r= catch_cr);
 591       polygon([cpp4,
 592                cppg,
 593                cpph,
 594                cpp10,
 595                cpp11,
 596                ]);
 597     }
 598     translate(cpp2) circle(r= catch_cr);
 599   }
 600 }
 601
 602 module CatchHeadProfile(){
 603   intersection(){
 604     translate(cppF){
 605       difference(){
 606         circle(r = dist2d(cppF, cppd));
 607         //circle(r = dist2d(cppF, cppa));
 608       }
 609     }
 610     polygon([ cppa,
 611               cppg,
 612               cpph,
 613               cppd,
 614               cppc,
 615               cppb ]);
 616   }
 617   polygon([ cppd,
 618             cppg,
 619             cppf,
 620             cppe,
 621             cpph ]);
 622 }
 623
 624
 625 module CatchCore(){ /////toplevel
 626   linear_extrude(height=catch_strap_thick, convexity=10)
 627     CatchAssemblyCoreProfile();
 628
 629   linear_extrude(height=catch_head_th, convexity=10)
 630     CatchHeadProfile();
 631
 632   translate(concat(cppB,[0])) hull(){
 633     translate([0,0, catch_knob_height + catch_head_th - catch_knob_dia/2])
 634       sphere(r = catch_knob_dia/2);
 635     cylinder(r = catch_knob_dia/2, h = 0.1);
 636   }
 637 }
 638
 639 module CatchPreDistort(){ /////toplevel
 640   scale(100 / sm_inner_rad)
 641     rotate([90,0,0])
 642     CatchCore();
 643 }
 644
 645 module CatchAssembly(){ /////toplevel
 646   rotate([0,0, -(cppe[0] + cppB[0] + catch_pin_slop) / sm_inner_rad * 360/TAU])
 647     translate([0,0, catch_assembly_dy])
 648     scale(sm_inner_rad / 100)
 649     import(str("poster-tube-lid,CatchPostDistort-fa",
 650                (coarse ? 20 : 3),
 651                ".stl"),
 652            convexity=20);
 653
 654   SomeStrap(){
 655     union(){ }
 656     union(){
 657       translate([-200, -200, -200])
 658         cube([400, 200, 400]);
 659     }
 660   }
 661 }
 662
 663 module CatchDemo(){ /////toplevel
 664   color("blue") translate([0,0,
 665                            -catch_assembly_dy
 666              ])
 667     CatchAssembly();
 668   translate([0,0,+side_height
 669              ])
 670     Cover();
 671 }
 672
 673 module CatchDemoS(){ /////toplevel
 674   color("blue") translate([0,0,
 675              -catch_assembly_dy
 676              ])
 677     CatchAssembly();
 678   intersection(){
 679     translate([0,0,+side_height
 680                ])
 681       Cover();
 682     mirror([0,1,0]) translate([-250,33,0]) cube([500,500,500]);
 683   }
 684   color("black")
 685     translate([0,-33,0])
 686     cube([6.15, 2,2], center=true);
 687 }
 688
 689 module CatchPinProfileDemo(){ /////toplevel
 690   echo("G ",
 691        cpp2[0] - cpp1[0],
 692        bayo_n[0] - bayo_e[0]);
 693   color("blue") translate([0,0,
 694                            +1,
 695              ]) {
 696     CatchAssemblyCoreProfile();
 697     CatchHeadProfile();
 698   }
 699   polygon(bayo_polygon, convexity=10);
 700 }
 701
 702 //ProfilesDemo();
 703 //BayonetCutout();
 704 //MainProfile();
 705 //Cover();
 706 //Jig();
 707 //CoverTest();