X-Git-Url: http://www.chiark.greenend.org.uk/ucgi/~ianmdlvl/git?p=dgit.git;a=blobdiff_plain;f=dgit-maint-gbp.7.pod;h=b8abd66cb6dcce1713ddc6dcb9b15114f412339b;hp=3c438ab101b41f069ed9cbfa29b46b12c01c3b02;hb=3193ca2bad512d2563797eca11ceb9d707a65004;hpb=1d01e5ebb230a058093afa0058cde2429545fc54

diff --git a/dgit-maint-gbp.7.pod b/dgit-maint-gbp.7.pod
index 3c438ab1..b8abd66c 100644
--- a/dgit-maint-gbp.7.pod
+++ b/dgit-maint-gbp.7.pod
@@ -31,6 +31,15 @@ normally used with patches-unapplied.
 
 =head1 GIT CONFIGURATION
 
+If you have configured an I<export-dir> in your gbp.conf, you should
+tell dgit about it:
+
+=over 4
+
+    % git config --global dgit.default.build-products-dir /home/spwhitton/build-area
+
+=back
+
 If you run
 
 =over 4
@@ -46,20 +55,24 @@ branch, never the dgit patches-applied branch.
 
 =head1 BUILDING
 
-You can perform builds like this:
+You can perform test builds like this:
 
 =over 4
 
-    % dgit [--allow-dirty] gbp-build [OPTIONS]
+    % dgit [--include-dirty] gbp-build [OPTIONS]
 
 =back
 
-where I<--allow-dirty> is needed for testing uncommitted changes, and
+where I<--include-dirty> is needed for testing uncommitted changes, and
 I<OPTIONS> are any further options to be passed on to
 gbp-buildpackage(1).
 
-When you are ready to build for upload, you will probably want to use
-sbuild(1) or pbuilder(1), or do a source-only upload.  Either
+If you are doing a source-only upload, you do not need to prepare a
+I<_source.changes>, as B<dgit push-source> will take of that on your
+behalf.
+
+If you need to include binaries with your upload, you will probably
+want to use sbuild(1), pbuilder(1) or cowbuilder(1):
 
 =over 4
 
@@ -67,37 +80,33 @@ sbuild(1) or pbuilder(1), or do a source-only upload.  Either
 
 =back
 
-or
+replacing 'sbuild' with 'pbuilder' or 'cowbuilder' if appropriate.
 
-=over 4
+We use I<--rm-old-changes> to ensure that there is exactly one changes
+file corresponding to this package, so we can be confident we're
+uploading what we intend (though B<dgit push> will do some safety
+checks).
 
-    % dgit --rm-old-changes gbp-build --git-pbuilder
+Note that none of the commands in this section are required to upload
+with dgit.  You can invoke gbp-buildpackage(1), pbuilder(1),
+cowbuilder(1) and sbuild(1) directly.  However, the defaults for these
+tools may leave you with something that dgit will refuse to upload
+because it doesn't match your git HEAD.
 
-=back
+As a general rule, leave all signing and tagging to dgit.
+
+=head1 UPLOADING
 
-or
+Don't use I<--git-tag>: B<dgit push> will do this for you.  To do a
+source-only upload:
 
 =over 4
 
-    % dgit --rm-old-changes --gbp build-source
+    % dgit --gbp push-source
 
 =back
 
-We use I<--rm-old-changes> to ensure that there is exactly one changes
-file corresponding to this package, so we can be confident we're
-uploading what we intend (though B<dgit push> will do some safety
-checks).
-
-Note that all of the commands in this section are not required to
-upload with dgit.  You can invoke gbp-buildpackage(1), pbuilder(1) and
-sbuild(1) directly.  However, the defaults for these tools may leave
-you with something that dgit will refuse to upload because it doesn't
-match your git HEAD.  As a general rule, leave all signing and tagging
-to dgit.
-
-=head1 UPLOADING
-
-Don't use I<--git-tag>: B<dgit push> will do this for you.  To upload:
+or if you need to include binaries,
 
 =over 4
 
@@ -106,7 +115,7 @@ Don't use I<--git-tag>: B<dgit push> will do this for you.  To upload:
 =back
 
 This will push your git history to the dgit-repos, but you probably
-want to follow it up with a push to alioth.
+want to follow it up with a push to salsa.
 
 You will need to pass I<--overwrite> if the previous upload was not
 performed with dgit.