setting('layer_height', 0.1, float, 'basic', _('Quality')).setRange(0.0001).setLabel(_("Layer height (mm)"), _("Layer height in millimeters.\nThis is the most important setting to determine the quality of your print. Normal quality prints are 0.1mm, high quality is 0.06mm. You can go up to 0.25mm with an Ultimaker for very fast prints at low quality."))
setting('wall_thickness', 0.8, float, 'basic', _('Quality')).setRange(0.0).setLabel(_("Shell thickness (mm)"), _("Thickness of the outside shell in the horizontal direction.\nThis is used in combination with the nozzle size to define the number\nof perimeter lines and the thickness of those perimeter lines."))
-setting('retraction_enable', False, bool, 'basic', _('Quality')).setLabel(_("Enable retraction"), _("Retract the filament when the nozzle is moving over a none-printed area. Details about the retraction can be configured in the advanced tab."))
+setting('retraction_enable', True, bool, 'basic', _('Quality')).setLabel(_("Enable retraction"), _("Retract the filament when the nozzle is moving over a none-printed area. Details about the retraction can be configured in the advanced tab."))
setting('solid_layer_thickness', 0.6, float, 'basic', _('Fill')).setRange(0).setLabel(_("Bottom/Top thickness (mm)"), _("This controls the thickness of the bottom and top layers, the amount of solid layers put down is calculated by the layer thickness and this value.\nHaving this value a multiple of the layer thickness makes sense. And keep it near your wall thickness to make an evenly strong part."))
setting('fill_density', 20, float, 'basic', _('Fill')).setRange(0, 100).setLabel(_("Fill Density (%)"), _("This controls how densely filled the insides of your print will be. For a solid part use 100%, for an empty part use 0%. A value around 20% is usually enough.\nThis won't affect the outside of the print and only adjusts how strong the part becomes."))
setting('nozzle_size', 0.4, float, 'advanced', _('Machine')).setRange(0.1,10).setLabel(_("Nozzle size (mm)"), _("The nozzle size is very important, this is used to calculate the line width of the infill, and used to calculate the amount of outside wall lines and thickness for the wall thickness you entered in the print settings."))
setting('retraction_dual_amount', 16.5, float, 'advanced', _('Retraction')).setRange(0).setLabel(_("Dual extrusion switch amount (mm)"), _("Amount of retraction when switching nozzle with dual-extrusion, set at 0 for no retraction at all. A value of 16.0mm seems to generate good results."))
setting('retraction_min_travel', 1.5, float, 'expert', _('Retraction')).setRange(0).setLabel(_("Minimum travel (mm)"), _("Minimum amount of travel needed for a retraction to happen at all. To make sure you do not get a lot of retractions in a small area."))
setting('retraction_combing', True, bool, 'expert', _('Retraction')).setLabel(_("Enable combing"), _("Combing is the act of avoiding holes in the print for the head to travel over. If combing is disabled the printer head moves straight from the start point to the end point and it will always retract."))
-setting('retraction_minimal_extrusion',0.1, float,'expert', _('Retraction')).setRange(0).setLabel(_("Minimal extrusion before retracting (mm)"), _("The minimal amount of extrusion that needs to be done before retracting again if a retraction needs to happen before this minimal is reached the retraction is ignored.\nThis avoids retraction a lot on the same piece of filament which flattens the filament and causes grinding issues."))
+setting('retraction_minimal_extrusion',0.02, float,'expert', _('Retraction')).setRange(0).setLabel(_("Minimal extrusion before retracting (mm)"), _("The minimal amount of extrusion that needs to be done before retracting again if a retraction needs to happen before this minimal is reached the retraction is ignored.\nThis avoids retraction a lot on the same piece of filament which flattens the filament and causes grinding issues."))
setting('bottom_thickness', 0.3, float, 'advanced', _('Quality')).setRange(0).setLabel(_("Initial layer thickness (mm)"), _("Layer thickness of the bottom layer. A thicker bottom layer makes sticking to the bed easier. Set to 0.0 to have the bottom layer thickness the same as the other layers."))
setting('object_sink', 0.0, float, 'advanced', _('Quality')).setLabel(_("Cut off object bottom (mm)"), _("Sinks the object into the platform, this can be used for objects that do not have a flat bottom and thus create a too small first layer."))
#setting('enable_skin', False, bool, 'advanced', _('Quality')).setLabel(_("Duplicate outlines"), _("Skin prints the outer lines of the prints twice, each time with half the thickness. This gives the illusion of a higher print quality."))
""", str, 'alteration', 'alteration')
setting('startMode', 'Simple', ['Simple', 'Normal'], 'preference', 'hidden')
+setting('oneAtATime', 'True', bool, 'preference', 'hidden')
setting('lastFile', os.path.normpath(os.path.join(os.path.dirname(os.path.abspath(__file__)), '..', 'resources', 'example', 'UltimakerRobot_support.stl')), str, 'preference', 'hidden')
setting('save_profile', 'False', bool, 'preference', 'hidden').setLabel(_("Save profile on slice"), _("When slicing save the profile as [stl_file]_profile.ini next to the model."))
setting('filament_cost_kg', '0', float, 'preference', 'hidden').setLabel(_("Cost (price/kg)"), _("Cost of your filament per kg, to estimate the cost of the final print."))
~ianmdlvl / cura.git / blobdiff