From: Ian Jackson Date: Tue, 1 Mar 2022 20:43:18 +0000 (+0000) Subject: fairphone4-case: docs X-Git-Url: http://www.chiark.greenend.org.uk/ucgi/~ianmdlvl/git?a=commitdiff_plain;h=5cdd4b2ce1090e58dc6d87e45c32a4005e049ada;p=reprap-play.git fairphone4-case: docs Signed-off-by: Ian Jackson --- diff --git a/fairphone4-case.scad b/fairphone4-case.scad index d795f0e..eee4ddb 100644 --- a/fairphone4-case.scad +++ b/fairphone4-case.scad @@ -9,17 +9,12 @@ // // 1. You will want to git clone this repository. // -// 2. Decide about the notification LED aperture. See the variable -// led_window_style, below. The default here is "ad-hoc -// multi-colour", which can produces a translucent (clear-ish) -// window set into the lid, even on a single-nozzle printer. -// See "Ad-hoc multi-colour", below. +// 2. // // 3. use "make" to generate the necessary files: // // make -j8 fairphone-case.auto.scads `for f in \ // HingePrint \ -// LidWindowPrint \ // LidPrint \ // OneKeeperPrint \ // Case \ @@ -28,34 +23,12 @@ // 4. Print them. Case and OneKeeperPrint should probably be // the same colour. // -// For Lid and LidWindowPrint, if you are doing ad-hoc -// multi-colour: -// i. Set up for clear filament -// ii. Print LidWindowPrint. Wait for it to finish. -// It won't take long. As soon as it finishes, tell -// your printer to warm up (so that in fact it does -// not cool down). -// iii. Leaving the output so far on the printbed, reload -// your printer with the main lid colour. -// iv. Print LidPrint. You can let this go unattended. +// 5. Assemble the hinge. // -// 5. Assemble the hinge. You will need 4x M2 12mm machine screws -// and 8x M2 full nuts. -// -// Make sure you get the hinge the right way round. If you're not -// sure, run -// openscad fairphone-case,DemoHinge.auto.scad -// to see an assembly diagram. -// -// The nuts recess into the hinge. You will want very fine -// pliers. As you screw each screw in, add the second nut when -// the screw thread emerges from the first - this will be a -// locknut. Screw each screw to an appropriate tightness for the -// hinge stiffness. You want the lid-side hinge to be stiffer as -// that makes closing the case work better. -// -// When you have the stiffness right, tighten the locknuts onto -// each first nut. +// Cut short bits of wire +// Push in with long bit of wire +// Use gas flame to melt end of 2.85mm PLA +// Dab // // 6. In use: // @@ -67,27 +40,6 @@ // portrait orientation only right now). See // openscad fairphone-case,DemoPropAngles.auto.scad // -// Ad-hoc multi-colour -// -// This file is set up to let you make a translucent window using a -// single-extruder printer, using a "two print run" technique. This -// works well with our Lulzbot TAZ 5 and Aleph Objects' version of -// Cura. If you are using a different printer, you may need to -// adjust the parameters or try a different technique. In particular, -// initial_layer_thick -// set so that the window is one layer thick -// initial_layer_width -// set so that the slicer draws a rectangle around the whole -// object, rather than putting a "skirt" or anything inside -// -// If you have a dual-extruder printer, you can set led_window_style -// to 2 and do a single print of LidPrint and LidWindowPrint. -// -// Alternatively you can set it to 1 (just a hole) or 0 (no hole). -// -// Thanks to Clare Boothby for the ad-hoc multi-colour technique (and -// the parameters for our Lulzbot TAZ 5 and Aleph Objects's Cura). -// // Other phones // // It might well be possible to adapt this file for other phones. @@ -96,7 +48,7 @@ // // AUTHORSHIP, COPYRIGHT, LICENCE, AND LACK OF WARRANTY // -// Copyright (C)2018 Ian Jackson. +// Copyright (C) 2018-2022 Ian Jackson. // // This program for generating a 3D model is free software: you can // redistribute it and/or modify it under the terms of the GNU