setting('filament_flow', 100., float, 'basic', 'Filament').setRange(1,300).setLabel('Flow (%)', 'Flow compensation, the amount of material extruded is multiplied by this value')
#setting('retraction_min_travel', 5.0, float, 'advanced', 'Retraction').setRange(0).setLabel('Minimum travel (mm)', 'Minimum amount of travel needed for a retraction to happen at all. To make sure you do not get a lot of retractions in a small area')
setting('retraction_speed', 40.0, float, 'advanced', 'Retraction').setRange(0.1).setLabel('Speed (mm/s)', 'Speed at which the filament is retracted, a higher retraction speed works better. But a very high retraction speed can lead to filament grinding.')
-setting('retraction_amount', 4.5, float, 'advanced', 'Retraction').setRange(0).setLabel('Distance (mm)', 'Amount of retraction, set at 0 for no retraction at all. A value of 2.0mm seems to generate good results.')
+setting('retraction_amount', 4.5, float, 'advanced', 'Retraction').setRange(0).setLabel('Distance (mm)', 'Amount of retraction, set at 0 for no retraction at all. A value of 4.5mm seems to generate good results.')
#setting('retraction_extra', 0.0, float, 'advanced', 'Retraction').setRange(0).setLabel('Extra length on start (mm)', 'Extra extrusion amount when restarting after a retraction, to better "Prime" your extruder after retraction.')
+setting('retraction_dual_amount', 16.5, float, 'advanced', 'Retraction').setRange(0).setLabel('Dual extrusion switch amount (mm)', 'Amount of retraction when switching nozzle with dual-extrusion, set at 0 for no retraction at all. A value of 16.0mm seems to generate good results.')
setting('bottom_thickness', 0.3, float, 'advanced', 'Quality').setRange(0).setLabel('Initial layer thickness (mm)', 'Layer thickness of the bottom layer. A thicker bottom layer makes sticking to the bed easier. Set to 0.0 to have the bottom layer thickness the same as the other layers.')
setting('object_sink', 0.0, float, 'advanced', 'Quality').setLabel('Cut off object bottom (mm)', 'Sinks the object into the platform, this can be used for objects that do not have a flat bottom and thus create a too small first layer.')
#setting('enable_skin', False, bool, 'advanced', 'Quality').setLabel('Duplicate outlines', 'Skin prints the outer lines of the prints twice, each time with half the thickness. This gives the illusion of a higher print quality.')
G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+M84 ;steppers off
+G90 ;absolute positioning
+""", str, 'alteration', 'alteration')
+#######################################################################################
+setting('start2.gcode', """;Sliced at: {day} {date} {time}
+;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+;Print time: {print_time}
+;Filament used: {filament_amount}m {filament_weight}g
+;Filament cost: {filament_cost}
+G21 ;metric values
+G90 ;absolute positioning
+M107 ;start with the fan off
+
+G28 X0 Y0 ;move X/Y to min endstops
+G28 Z0 ;move Z to min endstops
+
+G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+
+T1
+G92 E0 ;zero the extruded length
+G1 F200 E10 ;extrude 10mm of feed stock
+G92 E0 ;zero the extruded length again
+G1 F200 E-{retraction_dual_amount}
+
+T0
+G92 E0 ;zero the extruded length
+G1 F200 E10 ;extrude 10mm of feed stock
+G92 E0 ;zero the extruded length again
+G1 F{travel_speed}
+M117 Printing...
+""", str, 'alteration', 'alteration')
+#######################################################################################
+setting('end2.gcode', """;End GCode
+M104 T0 S0 ;extruder heater off
+M104 T1 S0 ;extruder heater off
+M140 S0 ;heated bed heater off (if you have it)
+
+G91 ;relative positioning
+G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+
M84 ;steppers off
G90 ;absolute positioning
""", str, 'alteration', 'alteration')
settingsDictionary['filament_diameter3'].addCondition(lambda : int(getPreference('extruder_amount')) > 2)
settingsDictionary['filament_diameter4'].addCondition(lambda : int(getPreference('extruder_amount')) > 3)
settingsDictionary['support_dual_extrusion'].addCondition(lambda : int(getPreference('extruder_amount')) > 1)
+settingsDictionary['retraction_dual_amount'].addCondition(lambda : int(getPreference('extruder_amount')) > 1)
#Heated bed
settingsDictionary['print_bed_temperature'].addCondition(lambda : getPreference('has_heated_bed') == 'True')
postfix = ''
alterationContents = getAlterationFile(filename)
if filename == 'start.gcode':
+ if extruderCount > 1:
+ alterationContents = getAlterationFile("start%d.gcode" % (extruderCount))
#For the start code, hack the temperature and the steps per E value into it. So the temperature is reached before the start code extrusion.
#We also set our steps per E here, if configured.
eSteps = getPreferenceFloat('steps_per_e')
if bedTemp > 0 and not '{print_bed_temperature}' in alterationContents:
prefix += 'M190 S%f\n' % (bedTemp)
elif filename == 'end.gcode':
+ if extruderCount > 1:
+ alterationContents = getAlterationFile("end%d.gcode" % (extruderCount))
#Append the profile string to the end of the GCode, so we can load it from the GCode file later.
postfix = ';CURA_PROFILE_STRING:%s\n' % (getProfileString())
elif filename == 'replace.csv':
'supportLineWidth': int(profile.getProfileSettingFloat('support_rate') * profile.calculateEdgeWidth() * 1000 / 100),
'retractionAmount': int(profile.getProfileSettingFloat('retraction_amount') * 1000) if profile.getProfileSetting('retraction_enable') == 'True' else 0,
'retractionSpeed': int(profile.getProfileSettingFloat('retraction_speed')),
+ 'retractionAmountExtruderSwitch': int(profile.getProfileSettingFloat('retraction_dual_amount') * 1000),
'objectSink': int(profile.getProfileSettingFloat('object_sink') * 1000),
'minimalLayerTime': int(profile.getProfileSettingFloat('cool_min_layer_time')),
'minimalFeedrate': int(profile.getProfileSettingFloat('cool_min_feedrate')),
'coolHeadLift': 1 if profile.getProfileSetting('cool_head_lift') == 'True' else 0,
'startCode': profile.getAlterationFileContents('start.gcode', extruderCount),
- 'endCode': profile.getAlterationFileContents('end.gcode'),
+ 'endCode': profile.getAlterationFileContents('end.gcode', extruderCount),
'extruderOffset[1].X': int(profile.getPreferenceFloat('extruder_offset_x1') * 1000),
'extruderOffset[1].Y': int(profile.getPreferenceFloat('extruder_offset_y1') * 1000),
~ianmdlvl / cura.git / commitdiff