# LulzBot Mini slice settings for use with the simple slice selection. This needs to be further modified to only be used when the Mini machine config is loaded.
if profile.getMachineSetting('machine_type') == 'lulzbot_mini':
+ put('fill_density', '30')
put('print_temperature', '0')
put('print_bed_temperature', '0')
put('retraction_speed', '25')
+ put('retraction_hop', '0.1')
put('bottom_thickness', '0.425')
put('layer0_width_factor', '125')
- put('fan_speed', '10')
- put('fan_speed_max', '50')
+ put('cool_min_layer_time', '15')
put('cool_head_lift', 'True')
put('end.gcode', """;End GCode
- M104 T0 S0 ;extruder heater off
- M104 T1 S0 ;extruder heater off
- M140 S0 ;heated bed heater off (if you have it)
- G91 ;relative positioning
- G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
- G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
- G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
- M84 ;steppers off
- G90 ;absolute positioning
+ M400
+ M104 S0 ; Hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E0 ; set extruder to 0
+ G1 E-3 F300 ; retract a bit to relieve pressure
+ G1 X5 Y5 Z156 F10000 ; move to cooling positioning
+ M190 R60 ; wait for bed to cool
+ G1 X145 Y175 Z156 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
;{profile_string}""")
if self.printMaterialHIPS.GetValue() or self.printMaterialABS.GetValue():
put('solid_layer_thickness', '0.8')
- put('fill_density', '40')
put('retraction_amount', '1.5')
put('travel_speed', '175')
- put('start.gcode', """;LulzBot Mini
- ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ put('fan_speed_max', '75')
+ put('start.gcode', """;This Gcode has been generated specifically for the LulzBot Mini
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
;Filament used: {filament_amount}m {filament_weight}g
;Filament cost: {filament_cost}
;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
;M109 S{print_temperature} ;Uncomment to add your own temperature line
- G21 ; metric values
- G90 ; absolute positioning
- M82 ; set extruder to absolute mode
- M107 ; start with the fan off
- G92 E0 ; set extruder position to 0
- M140 S110 ; get bed heating up
- G28 ; home all
- M109 S150 ; set to cleaning temp and wait
- G1 Z150 E-45 F200 ; suck up XXmm of filament
- M109 S170 ; heat up rest of way
- G1 X45 Y178 F11520 ; move behind scraper
- G1 Z0 F1200 ; CRITICAL: set Z to height of top of scraper
- G1 X45 Y178 Z-1 F4000 ; wiping ; plunge into wipe pad
- G1 X55 Y176 Z-.5 F4000 ; wiping
- G1 X45 Y178 F4000 ; wiping
- G1 X55 Y176 F4000 ; wiping
- G1 X45 Y178 F4000 ; wiping
- G1 X55 Y176 F4000 ; wiping
- G1 X45 Y178 F4000 ; wiping
- G1 X55 Y176 F4000 ; wiping
- G1 X60 Y178 F4000 ; wiping
- G1 X80 Y176 F4000 ; wiping
- G1 X60 Y178 F4000 ; wiping
- G1 X80 Y176 F4000 ; wiping
- G1 X60 Y178 F4000 ; wiping
- G1 X90 Y176 F4000 ; wiping
- G1 X80 Y178 F4000 ; wiping
- G1 X100 Y176 F4000 ; wiping
- G1 X80 Y178 F4000 ; wiping
- G1 X100 Y176 F4000 ; wiping
- G1 X80 Y178 F4000 ; wiping
- G1 X100 Y176 F4000 ; wiping
- G1 X110 Y178 F4000 ; wiping
- G1 X100 Y176 F4000 ; wiping
- G1 X110 Y178 F4000 ; wiping
- G1 X100 Y176 F4000 ; wiping
- G1 X110 Y178 F4000 ; wiping
- G1 X115 Y175 Z-1.5 F1000 ; wipe slower and bury noz in cleanish area
- G1 Z10 ; raise z
- G28 X0 Y0 ; home x and y
- M109 S170 ; set to probing temp
- G29 ; Probe
- G1 X5 Y15 Z10 F5000 ; get out the way
- M109 S230 ; set extruder temp and wait
- G1 Z2 E5 F200 ; extrude filament back into nozzle
- M140 S110 ; get bed temping up during first layer
- M206 X0.0 Y0.0 Z0.0 ; offset home position for fine tuning""")
+ G21 ; metric values
+ G90 ; absolute positioning
+ M82 ; set extruder to absolute mode
+ M107 ; start with the fan off
+ G92 E0 ; set extruder position to 0
+ M140 S110 ; get bed heating up
+ G28 ; home all
+ M109 S150 ; set to cleaning temp and wait
+ G1 Z150 E-30 F75 ; suck up XXmm of filament
+ M109 S170 ; heat up rest of way
+ G1 X45 Y174 F11520 ; move behind scraper
+ G1 Z0 F1200 ; CRITICAL: set Z to height of top of scraper
+ G1 X45 Y174 Z-.5 F4000 ; wiping ; plunge into wipe pad
+ G1 X55 Y172 Z-.5 F4000 ; wiping
+ G1 X45 Y174 Z0 F4000 ; wiping
+ G1 X55 Y172 F4000 ; wiping
+ G1 X45 Y174 F4000 ; wiping
+ G1 X55 Y172 F4000 ; wiping
+ G1 X45 Y174 F4000 ; wiping
+ G1 X55 Y172 F4000 ; wiping
+ G1 X60 Y174 F4000 ; wiping
+ G1 X80 Y172 F4000 ; wiping
+ G1 X60 Y174 F4000 ; wiping
+ G1 X80 Y172 F4000 ; wiping
+ G1 X60 Y174 F4000 ; wiping
+ G1 X90 Y172 F4000 ; wiping
+ G1 X80 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X80 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X80 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X110 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X110 Y174 F4000 ; wiping
+ G1 X100 Y172 F4000 ; wiping
+ G1 X110 Y174 F4000 ; wiping
+ G1 X115 Y172 Z-0.5 F1000 ; wipe slower and bury noz in cleanish area
+ G1 Z10 ; raise z
+ G28 X0 Y0 ; home x and y
+ M109 S170 ; set to probing temp
+ M204 S300 ; set accel for probing
+ G29 ; Probe
+ M204 S2000 ; set accel back to normal
+ G1 X5 Y15 Z10 F5000 ; get out the way
+ M400 ; clear buffer
+ G4 S1 ; pause
+ M109 S230 ; set extruder temp and wait
+ G4 S25 ; wait for bed to temp up
+ G1 Z2 E0 F75 ; extrude filament back into nozzle
+ M140 S110 ; get bed temping up during first layer""")
+ if self.printMaterialHIPS.GetValue():
+ put('bottom_layer_speed', '30')
+ put('fan_full_height', '2')
+ put('fan_speed', '45')
+ put('cool_min_feedrate', '45')
+ put('brim_line_count', '10')
+ put('raft_airgap', '0.5')
+ put('plugin_config', """(lp1
+ (dp2
+ S'params'
+ p3
+ (dp4
+ S'targetL'
+ p5
+ V
+ sS'extruderTwo'
+ p6
+ V
+ sS'flowrateTwo'
+ p7
+ V
+ sS'targetZ'
+ p8
+ V2
+ sS'flowrate'
+ p9
+ V
+ sS'fanSpeed'
+ p10
+ V
+ sS'platformTemp'
+ p11
+ V85
+ p12
+ sS'speed'
+ p13
+ V
+ sS'flowrateOne'
+ p14
+ V
+ sS'extruderOne'
+ p15
+ V
+ ssS'filename'
+ p16
+ S'TweakAtZ.py'
+ p17
+ sa.""")
+ if self.printTypeLow.GetValue():
+ put('layer_height', '0.38')
+ put('print_speed', '85')
+ put('infill_speed', '110')
+ put('inset0_speed', '70')
+ put('insetx_speed', '80')
+ if self.printTypeNormal.GetValue():
+ put('layer_height', '0.25')
+ put('print_speed', '65')
+ put('infill_speed', '85')
+ put('inset0_speed', '45')
+ put('insetx_speed', '50')
+ put('skirt_minimal_length', '200')
+ if self.printTypeHigh.GetValue():
+ put('layer_height', '0.14')
+ put('print_speed', '30')
+ put('infill_speed', '50')
+ put('inset0_speed', '20')
+ put('insetx_speed', '25')
+ if self.printMaterialABS.GetValue():
+ put('cool_min_feedrate', '10')
+ put('fan_enabled', 'False')
+ put('fan_full_height', '5')
+ put('fan_speed', '40')
+ if self.printTypeLow.GetValue():
+ put('layer_height', '0.38')
+ put('print_speed', '85')
+ put('bottom_layer_speed', '30')
+ put('infill_speed', '110')
+ put('inset0_speed', '70')
+ put('insetx_speed', '80')
+ put('brim_line_count', '8')
+ if self.printTypeNormal.GetValue():
+ put('layer_height', '0.25')
+ put('print_speed', '75')
+ put('bottom_layer_speed', '25')
+ put('infill_speed', '80')
+ put('inset0_speed', '60')
+ put('insetx_speed', '70')
+ if self.printTypeHigh.GetValue():
+ put('layer_height', '0.14')
+ put('print_speed', '60')
+ put('bottom_layer_speed', '25')
+ put('infill_speed', '60')
+ put('inset0_speed', '40')
+ put('insetx_speed', '50')
+ put('fan_full_height', '5')
+
elif self.printMaterialPLA.GetValue():
+ put('solid_layer_thickness', '1')
+ put('retraction_amount', '3')
+ put('skirt_minimal_length', '250')
+ put('skirt_line_count', '3')
+ put('fan_full_height', '1')
+ put('fan_speed', '75')
+ put('fan_speed_max', '100')
+ put('cool_min_feedrate', '15')
+ put('brim_line_count', '2')
put('start.gcode', """;LulzBot Mini
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
M84 ;steppers off
G90 ;absolute positioning
;{profile_string}""")
-
- nozzle_size = float(get('nozzle_size'))
- if self.printMaterialHIPS.GetValue():
- put('retraction_hop', '0.6')
- put('bottom_layer_speed', '30')
- put('fan_full_height', '5')
- put('cool_min_feedrate', '45')
- if self.printTypeLow.GetValue():
- put('layer_height', '0.38')
- put('print_speed', '85')
- put('infill_speed', '115')
- put('inset0_speed', '75')
- put('insetx_speed', '80')
- if self.printTypeNormal.GetValue():
- put('layer_height', '0.25')
- put('print_speed', '65')
- put('infill_speed', '85')
- put('inset0_speed', '45')
- put('insetx_speed', '50')
- if self.printTypeHigh.GetValue():
- put('layer_height', '0.14')
- put('print_speed', '40')
- put('infill_speed', '65')
- put('inset0_speed', '30')
- put('insetx_speed', '35')
- if self.printMaterialABS.GetValue():
- put('retraction_hop', '0.6')
- put('cool_min_feedrate', '10')
- put('fan_enabled', 'False')
- if self.printTypeLow.GetValue():
- put('layer_height', '0.38')
- put('print_speed', '85')
- put('bottom_layer_speed', '30')
- put('infill_speed', '110')
- put('inset0_speed', '70')
- put('insetx_speed', '80')
- put('brim_line_count', '8')
- if self.printTypeNormal.GetValue():
- put('layer_height', '0.25')
- put('print_speed', '75')
- put('bottom_layer_speed', '25')
- put('infill_speed', '80')
- put('inset0_speed', '60')
- put('insetx_speed', '70')
- if self.printTypeHigh.GetValue():
- put('layer_height', '0.14')
- put('print_speed', '60')
- put('bottom_layer_speed', '25')
- put('infill_speed', '60')
- put('inset0_speed', '40')
- put('insetx_speed', '50')
- put('fan_full_height', '5')
- put('skirt_line_count', '4')
- if self.printMaterialPLA.GetValue():
- put('solid_Layer_thickness', '1')
- put('fill_density', '70')
- put('retraction_amount', '3')
- put('retraction_hop', '0.5')
- put('travel_speed', '150')
- put('bottom_travel_speed', '30')
- put('fan_full_height', '1')
- put('cool_min_feedrate', '15')
- put('skirt_line_count', '2')
+ put("end.gcode", """M400
+ M104 S0 ; Hotend off
+ M140 S0 ; heated bed heater off (if you have it)
+ M107 ; fans off
+ G92 E0 ; set extruder to 0
+ G1 E-3 F300 ; retract a bit to relieve pressure
+ G1 X5 Y5 Z156 F10000 ; move to cooling positioning
+ M190 R60 ; wait for bed to cool
+ G1 X145 Y175 Z156 F1000 ; move to cooling positioning
+ M84 ; steppers off
+ G90 ; absolute positioning
+ ;{profile_string}""")
if self.printTypeLow.GetValue():
put('layer_height', '0.38')
put('print_speed', '90')
- put('infill_speed', '125')
+ put('infill_speed', '115')
put('inset0_speed', '75')
put('insetx_speed', '85')
if self.printTypeNormal.GetValue():
put('layer_height', '0.25')
- put('print_speed', '70')
+ put('print_speed', '50')
put('infill_speed', '95')
put('inset0_speed', '65')
put('insetx_speed', '75')
+ put('raft_airgap', '0.5')
if self.printTypeHigh.GetValue():
- pass
-
+ put('layer_height', '0.14')
+ put('print_speed', '30')
+ put('bottom_layer_speed', '25')
+ put('infill_speed', '75')
+ put('inset0_speed', '45')
+ put('insetx_speed', '55')
+ put('raft_airgap', '0.5')
nozzle_size = float(get('nozzle_size'))
put('filament_diameter', self.printMaterialDiameter.GetValue())
put('plugin_config', '')
~ianmdlvl / cura.git / commitdiff