# LulzBot Mini slice settings for use with the simple slice selection.
if profile.getMachineSetting('machine_type') == 'lulzbot_mini':
+ put('wall_thickness', '1')
put('fill_density', '30')
put('print_temperature', '0')
put('print_bed_temperature', '0')
put('retraction_hop', '0.1')
put('bottom_thickness', '0.425')
put('layer0_width_factor', '125')
+ put('travel_speed', '175')
put('cool_min_layer_time', '15')
- put('cool_head_lift', 'True')
+ put('skirt_minimal_length', '250')
+ put('brim_line_count', '10')
+ put('raft_airgap', '0.5')
put('end.gcode', """M400
- M104 S0 ; Hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E0 ; set extruder to 0
- G1 E-3 F300 ; retract a bit to relieve pressure
- G1 X5 Y5 Z156 F10000 ; move to cooling positioning
- M190 R60 ; wait for bed to cool
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}""")
+M104 S0 ; Hotend off
+M140 S0 ; heated bed heater off (if you have it)
+M107 ; fans off
+G92 E0 ; set extruder to 0
+G1 E-3 F300 ; retract a bit to relieve pressure
+G1 X5 Y5 Z156 F10000 ; move to cooling positioning
+M190 R60 ; wait for bed to cool
+M140 S0 ; Turn off bed temp
+G1 X145 Y175 Z156 F1000 ; move to cooling positioning
+M84 ; steppers off
+G90 ; absolute positioning
+;{profile_string}
+""")
if self.printMaterialHIPS.GetValue() or self.printMaterialABS.GetValue():
put('solid_layer_thickness', '0.8')
put('retraction_amount', '1.5')
- put('travel_speed', '175')
- put('fan_speed_max', '75')
put('start.gcode', """;This Gcode has been generated specifically for the LulzBot Mini
- ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
- ;Print time: {print_time}
- ;Filament used: {filament_amount}m {filament_weight}g
- ;Filament cost: {filament_cost}
- ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
- ;M109 S{print_temperature} ;Uncomment to add your own temperature line
- G21 ; metric values
- G90 ; absolute positioning
- M82 ; set extruder to absolute mode
- M107 ; start with the fan off
- G92 E0 ; set extruder position to 0
- M140 S110 ; get bed heating up
- G28 ; home all
- M109 S150 ; set to cleaning temp and wait
- G1 Z150 E-30 F75 ; suck up XXmm of filament
- M109 S170 ; heat up rest of way
- G1 X45 Y174 F11520 ; move behind scraper
- G1 Z0 F1200 ; CRITICAL: set Z to height of top of scraper
- G1 X45 Y174 Z-.5 F4000 ; wiping ; plunge into wipe pad
- G1 X55 Y172 Z-.5 F4000 ; wiping
- G1 X45 Y174 Z0 F4000 ; wiping
- G1 X55 Y172 F4000 ; wiping
- G1 X45 Y174 F4000 ; wiping
- G1 X55 Y172 F4000 ; wiping
- G1 X45 Y174 F4000 ; wiping
- G1 X55 Y172 F4000 ; wiping
- G1 X60 Y174 F4000 ; wiping
- G1 X80 Y172 F4000 ; wiping
- G1 X60 Y174 F4000 ; wiping
- G1 X80 Y172 F4000 ; wiping
- G1 X60 Y174 F4000 ; wiping
- G1 X90 Y172 F4000 ; wiping
- G1 X80 Y174 F4000 ; wiping
- G1 X100 Y172 F4000 ; wiping
- G1 X80 Y174 F4000 ; wiping
- G1 X100 Y172 F4000 ; wiping
- G1 X80 Y174 F4000 ; wiping
- G1 X100 Y172 F4000 ; wiping
- G1 X110 Y174 F4000 ; wiping
- G1 X100 Y172 F4000 ; wiping
- G1 X110 Y174 F4000 ; wiping
- G1 X100 Y172 F4000 ; wiping
- G1 X110 Y174 F4000 ; wiping
- G1 X115 Y172 Z-0.5 F1000 ; wipe slower and bury noz in cleanish area
- G1 Z10 ; raise z
- G28 X0 Y0 ; home x and y
- M109 S170 ; set to probing temp
- M204 S300 ; set accel for probing
- G29 ; Probe
- M204 S2000 ; set accel back to normal
- G1 X5 Y15 Z10 F5000 ; get out the way
- M400 ; clear buffer
- G4 S1 ; pause
- M109 S230 ; set extruder temp and wait
- G4 S25 ; wait for bed to temp up
- G1 Z2 E0 F75 ; extrude filament back into nozzle
- M140 S110 ; get bed temping up during first layer""")
+;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+;Print time: {print_time}
+;Filament used: {filament_amount}m {filament_weight}g
+;Filament cost: {filament_cost}
+;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+;M109 S{print_temperature} ;Uncomment to add your own temperature line
+G21 ; metric values
+G90 ; absolute positioning
+M82 ; set extruder to absolute mode
+M107 ; start with the fan off
+G92 E0 ; set extruder position to 0
+M140 S110 ; get bed heating up
+G28 ; home all
+M109 S150 ; set to cleaning temp and wait
+G1 Z150 E-30 F75 ; suck up XXmm of filament
+M109 S170 ; heat up rest of way
+G1 X45 Y174 F11520 ; move behind scraper
+G1 Z0 F1200 ; CRITICAL: set Z to height of top of scraper
+G1 X45 Y174 Z-.5 F4000 ; wiping ; plunge into wipe pad
+G1 X55 Y172 Z-.5 F4000 ; wiping
+G1 X45 Y174 Z0 F4000 ; wiping
+G1 X55 Y172 F4000 ; wiping
+G1 X45 Y174 F4000 ; wiping
+G1 X55 Y172 F4000 ; wiping
+G1 X45 Y174 F4000 ; wiping
+G1 X55 Y172 F4000 ; wiping
+G1 X60 Y174 F4000 ; wiping
+G1 X80 Y172 F4000 ; wiping
+G1 X60 Y174 F4000 ; wiping
+G1 X80 Y172 F4000 ; wiping
+G1 X60 Y174 F4000 ; wiping
+G1 X90 Y172 F4000 ; wiping
+G1 X80 Y174 F4000 ; wiping
+G1 X100 Y172 F4000 ; wiping
+G1 X80 Y174 F4000 ; wiping
+G1 X100 Y172 F4000 ; wiping
+G1 X80 Y174 F4000 ; wiping
+G1 X100 Y172 F4000 ; wiping
+G1 X110 Y174 F4000 ; wiping
+G1 X100 Y172 F4000 ; wiping
+G1 X110 Y174 F4000 ; wiping
+G1 X100 Y172 F4000 ; wiping
+G1 X110 Y174 F4000 ; wiping
+G1 X115 Y172 Z-0.5 F1000 ; wipe slower and bury noz in cleanish area
+G1 Z10 ; raise z
+G28 X0 Y0 ; home x and y
+M109 S170 ; set to probing temp
+M204 S300 ; set accel for probing
+G29 ; Probe
+M204 S2000 ; set accel back to normal
+G1 X5 Y15 Z10 F5000 ; get out the way
+M400 ; clear buffer
+G4 S1 ; pause
+M109 S230 ; set extruder temp and wait
+G4 S25 ; wait for bed to temp up
+G1 Z2 E0 F75 ; extrude filament back into nozzle
+M140 S110 ; get bed temping up during first layer
+""")
if self.printMaterialHIPS.GetValue():
put('bottom_layer_speed', '30')
put('fan_full_height', '2')
put('fan_speed', '45')
+ put('fan_speed_max', '75')
put('cool_min_feedrate', '45')
- put('raft_airgap', '0.5')
put('plugin_config', """(lp1
(dp2
S'params'
put('inset0_speed', '20')
put('insetx_speed', '25')
if self.printMaterialABS.GetValue():
- put('cool_min_feedrate', '10')
- put('fan_enabled', 'False')
put('fan_full_height', '5')
put('fan_speed', '40')
+ put('fan_speed_max', '75')
+ put('cool_min_feedrate', '10')
if self.printTypeLow.GetValue():
put('layer_height', '0.38')
put('print_speed', '85')
put('insetx_speed', '80')
if self.printTypeNormal.GetValue():
put('layer_height', '0.25')
- put('print_speed', '75')
+ put('print_speed', '50')
put('bottom_layer_speed', '25')
- put('infill_speed', '80')
- put('inset0_speed', '60')
- put('insetx_speed', '70')
+ put('infill_speed', '55')
+ put('inset0_speed', '45')
+ put('insetx_speed', '50')
if self.printTypeHigh.GetValue():
put('layer_height', '0.14')
- put('print_speed', '60')
+ put('print_speed', '50')
put('bottom_layer_speed', '25')
- put('infill_speed', '60')
- put('inset0_speed', '40')
+ put('infill_speed', '55')
+ put('inset0_speed', '45')
put('insetx_speed', '50')
- put('fan_full_height', '5')
-
elif self.printMaterialPLA.GetValue():
put('solid_layer_thickness', '1')
put('retraction_amount', '3')
- put('skirt_minimal_length', '250')
- put('skirt_line_count', '3')
+ put('bottom_layer_speed', '25')
+ put('infill_speed', '55')
+ put('inset0_speed', '45')
+ put('insetx_speed', '50')
put('fan_full_height', '1')
put('fan_speed', '75')
put('fan_speed_max', '100')
put('cool_min_feedrate', '15')
- put('start.gcode', """;LulzBot Mini
- ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
- ;Print time: {print_time}
- ;Filament used: {filament_amount}m {filament_weight}g
- ;Filament cost: {filament_cost}
- ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
- ;M109 S{print_temperature} ;Uncomment to add your own temperature line
-
- G21 ; metric values
- G90 ; absolute positioning
- M82 ; set extruder to absolute mode
- M107 ; start with the fan off
- G92 E0 ; set extruder position to 0
- M140 S65 ; get bed heating up
- G28 ; home all
- M109 S130 ; set to cleaning temp and wait
- G1 Z150 E-45 F200 ; suck up XXmm of filament
- M109 S140 ; heat up rest of way
- G1 X45 Y174 F11520 ; move behind scraper
- G1 Z0 F1200 ; CRITICAL: set Z to height of top of scraper
- G1 X45 Y174 Z-.5 F4000 ; wiping ; plunge into wipe pad
- G1 X55 Y172 Z-.5 F4000 ; wiping
- G1 X45 Y174 Z0 F4000 ; wiping
- G1 X55 Y172 F4000 ; wiping
- G1 X45 Y174 F4000 ; wiping
- G1 X55 Y172 F4000 ; wiping
- G1 X45 Y174 F4000 ; wiping
- G1 X55 Y172 F4000 ; wiping
- G1 X60 Y174 F4000 ; wiping
- G1 X80 Y172 F4000 ; wiping
- G1 X60 Y174 F4000 ; wiping
- G1 X80 Y172 F4000 ; wiping
- G1 X60 Y174 F4000 ; wiping
- G1 X90 Y172 F4000 ; wiping
- G1 X80 Y174 F4000 ; wiping
- G1 X100 Y172 F4000 ; wiping
- G1 X80 Y174 F4000 ; wiping
- G1 X100 Y172 F4000 ; wiping
- G1 X80 Y174 F4000 ; wiping
- G1 X100 Y172 F4000 ; wiping
- G1 X110 Y174 F4000 ; wiping
- G1 X100 Y172 F4000 ; wiping
- G1 X110 Y174 F4000 ; wiping
- G1 X100 Y172 F4000 ; wiping
- G1 X110 Y174 F4000 ; wiping
- G1 X115 Y172 Z-0.5 F1000 ; wipe slower and bury noz in cleanish area
- G1 Z10 ; raise z
- G28 X0 Y0 ; home x and y
- M109 S140 ; set to probing temp
- G29 ; Probe
- G1 X5 Y15 Z10 F5000 ; get out the way
- M109 S190 ; set extruder temp and wait
- G1 Z2 E5 F200 ; extrude filament back into nozzle
- M140 S65 ; get bed temping up during first layer
- M206 X0.0 Y0.0 Z0.0 ; offset home position for fine tuning""")
- put("end.gcode", """M400
- M104 S0 ; Hotend off
- M140 S0 ; heated bed heater off (if you have it)
- M107 ; fans off
- G92 E0 ; set extruder to 0
- G1 E-3 F300 ; retract a bit to relieve pressure
- G1 X5 Y5 Z156 F10000 ; move to cooling positioning
- M190 R60 ; wait for bed to cool
- G1 X145 Y175 Z156 F1000 ; move to cooling positioning
- M84 ; steppers off
- G90 ; absolute positioning
- ;{profile_string}""")
+ put('print_speed', '50')
+ put('start.gcode', """;This Gcode has been generated specifically for the LulzBot Mini
+;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+;Print time: {print_time}
+;Filament used: {filament_amount}m {filament_weight}g
+;Filament cost: {filament_cost}
+;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+;M109 S{print_temperature} ;Uncomment to add your own temperature line
+G21 ; metric values
+G90 ; absolute positioning
+M82 ; set extruder to absolute mode
+M107 ; start with the fan off
+G92 E0 ; set extruder position to 0
+M140 S75 ; get bed heating up
+G28 ; home all
+M109 S140 ; set to cleaning temp and wait
+G1 Z150 E-30 F75 ; suck up XXmm of filament
+M109 S140 ; heat up rest of way
+G1 X45 Y174 F11520 ; move behind scraper
+G1 Z0 F1200 ; CRITICAL: set Z to height of top of scraper
+G1 X45 Y174 Z-.5 F4000 ; wiping ; plunge into wipe pad
+G1 X55 Y172 Z-.5 F4000 ; wiping
+G1 X45 Y174 Z0 F4000 ; wiping
+G1 X55 Y172 F4000 ; wiping
+G1 X45 Y174 F4000 ; wiping
+G1 X55 Y172 F4000 ; wiping
+G1 X45 Y174 F4000 ; wiping
+G1 X55 Y172 F4000 ; wiping
+G1 X60 Y174 F4000 ; wiping
+G1 X80 Y172 F4000 ; wiping
+G1 X60 Y174 F4000 ; wiping
+G1 X80 Y172 F4000 ; wiping
+G1 X60 Y174 F4000 ; wiping
+G1 X90 Y172 F4000 ; wiping
+G1 X80 Y174 F4000 ; wiping
+G1 X100 Y172 F4000 ; wiping
+G1 X80 Y174 F4000 ; wiping
+G1 X100 Y172 F4000 ; wiping
+G1 X80 Y174 F4000 ; wiping
+G1 X100 Y172 F4000 ; wiping
+G1 X110 Y174 F4000 ; wiping
+G1 X100 Y172 F4000 ; wiping
+G1 X110 Y174 F4000 ; wiping
+G1 X100 Y172 F4000 ; wiping
+G1 X110 Y174 F4000 ; wiping
+G1 X115 Y172 Z-0.5 F1000 ; wipe slower and bury noz in cleanish area
+G1 Z10 ; raise z
+G28 X0 Y0 ; home x and y
+M109 S140 ; set to probing temp
+M204 S300 ; Set probing acceleration
+G29 ; Probe
+M204 S2000 ; Restore standard acceleration
+G1 X5 Y15 Z10 F5000 ; get out the way
+G4 S1 ; pause
+M400 ; clear buffer
+M109 S195 ; set extruder temp and wait
+G4 S15 ; wait for bed to temp up
+G1 Z2 E0 F75 ; extrude filament back into nozzle
+M140 S75 ; get bed temping up during first layer
+""")
if self.printTypeLow.GetValue():
put('layer_height', '0.38')
- put('print_speed', '90')
- put('infill_speed', '115')
- put('inset0_speed', '75')
- put('insetx_speed', '85')
if self.printTypeNormal.GetValue():
put('layer_height', '0.25')
- put('print_speed', '50')
- put('infill_speed', '95')
- put('inset0_speed', '65')
- put('insetx_speed', '75')
- put('raft_airgap', '0.5')
if self.printTypeHigh.GetValue():
- put('layer_height', '0.14')
- put('print_speed', '30')
- put('bottom_layer_speed', '25')
- put('infill_speed', '75')
- put('inset0_speed', '45')
- put('insetx_speed', '55')
- put('raft_airgap', '0.5')
+ put('layer_height', '0.14')
nozzle_size = float(get('nozzle_size'))
put('filament_diameter', self.printMaterialDiameter.GetValue())
put('plugin_config', '')
put('nozzle_size', '0.35')
put('print_temperature', '0')
put('print_bed_temperature', '0')
- put('start.gcode', """;Sliced at: {day} {date} {time}
+ put('start.gcode', """;This Gcode has been generated specifically for the LulzBot TAZ
+ ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
;Filament used: {filament_amount}m {filament_weight}g
put('fan_full_height', '5')
put('fan_speed', '40')
put('fan_speed_max', '75')
- put('skirt_line_count', '4')
elif self.printMaterialPLA.GetValue():
if self.printTypeLow.GetValue():
put('layer_height', '0.28')
put('fan_full_height', '1')
put('fan_speed', '75')
put('cool_min_feedrate', '15')
- put('skirt_line_count', '3')
put('fill_overlap', '0')
if self.printTypeNormal.GetValue():
put('layer_height', '0.21')
put('fan_full_height', '1')
put('fan_speed', '75')
put('cool_min_feedrate', '15')
- put('skirt_line_count', '3')
if self.printTypeHigh.GetValue():
put('layer_height', '0.14')
put('wall_thickness', '1.05')
put('cool_min_layer_time', '20')
put('skirt_minimal_length', '0')
put('fan_full_height', '0.28')
- put('skirt_line_count', '2')
put('fill_overlap', '10')
elif not profile.getMachineSetting('machine_type') == 'lulzbot_mini' and not profile.getMachineSetting('machine_type') == 'lulzbot_TAZ':
nozzle_size = float(get('nozzle_size'))
~ianmdlvl / cura.git / commitdiff