-#Name: Tweak At Z 3.1.2
+#Name: Tweak At Z 3.2
#Info: Change printing parameters at a given height
#Help: TweakAtZ
#Depend: GCode
#Param: targetZ(float:5.0) Z height to tweak at (mm)
#Param: targetL(int:) (ALT) Layer no. to tweak at
#Param: speed(int:) New Speed (%)
-#Param: flowrate(int:) New Flow Rate (%)
+#Param: flowrate(int:) New General Flow Rate (%)
+#Param: flowrateOne(int:) New Flow Rate Extruder 1 (%)
+#Param: flowrateTwo(int:) New Flow Rate Extruder 2 (%)
#Param: platformTemp(int:) New Bed Temp (deg C)
#Param: extruderOne(int:) New Extruder 1 Temp (deg C)
#Param: extruderTwo(int:) New Extruder 2 Temp (deg C)
## Written by Steven Morlock, smorloc@gmail.com
## Modified by Ricardo Gomez, ricardoga@otulook.com, to add Bed Temperature and make it work with Cura_13.06.04+
-## Modified by Stefan Heule, Dim3nsioneer@gmx.ch, to add Flow Rate, restoration of initial values when returning to low Z, extended stage numbers, direct stage manipulation by GCODE-comments, UltiGCode regocnition, addition of fan speed, alternative selection by layer no., disabling extruder three
+## Modified by Stefan Heule, Dim3nsioneer@gmx.ch, to add Flow Rate, restoration of initial values when returning to low Z, extended stage numbers, direct stage manipulation by GCODE-comments, UltiGCode regocnition, addition of fan speed, alternative selection by layer no., disabling extruder three, addition of flow rate for specific extruder
## This script is licensed under the Creative Commons - Attribution - Share Alike (CC BY-SA) terms
# Uses -
# M220 S<factor in percent> - set speed factor override percentage
# M221 S<factor in percent> - set flow factor override percentage
+# M221 S<factor in percent> T<0-#toolheads> - set flow factor override percentage for single extruder
# M104 S<temp> T<0-#toolheads> - set extruder <T> to target temperature <S>
# M140 S<temp> - set bed target temperature
# M106 S<PWM> - set fan speed to target speed <S>
#V3.0.1: TweakAtZ-state default 1 (i.e. the plugin works without any TweakAtZ comment)
#V3.1: Recognizes UltiGCode and deactivates value reset, fan speed added, alternatively layer no. to tweak at, extruder three temperature disabled by '#Ex3'
#V3.1.1: Bugfix reset flow rate
-#V3.1.2: Bugfix disable TweakAtZ on Cool Head Lift / Retraction Hop
+#V3.1.2: Bugfix disable TweakAtZ on Cool Head Lift
+#V3.2: Flow rate for specific extruder added (only for 2 extruders), bugfix parser, added speed reset at the end of the print
-version = '3.1.2'
+version = '3.2'
import re
elif ";LAYER:" in key:
m = re.search('^[+-]?[0-9]*', subPart)
else:
- m = re.search('^[0-9]+\.?[0-9]*', subPart)
+ m = re.search('^[-]?[0-9]+\.?[0-9]*', subPart) #the minus at the beginning allows for negative values, e.g. for delta printers
if m == None:
return default
try:
old_speed = 100
old_flowrate = 100
+old_flowrateOne = 100
+old_flowrateTwo = 100
old_platformTemp = -1
old_extruderOne = -1
old_extruderTwo = -1
with open(filename, "w") as f:
for line in lines:
- f.write(line)
+ if not ('M84' in line or 'M25' in line):
+ f.write(line)
if 'FLAVOR:UltiGCode' in line: #Flavor is UltiGCode! No reset of values
no_reset = 1
if ';TweakAtZ-state' in line: #checks for state change comment
if 'M106' in line and state < 3: #looking for fan speed
old_fanSpeed = getValue(line, 'S', old_fanSpeed)
if 'M221' in line and state < 3: #looking for flow rate
- old_flowrate = getValue(line, 'S', old_flowrate)
+ tmp_extruder = getValue(line,'T',None)
+ if tmp_extruder == None: #check if extruder is specified
+ old_flowrate = getValue(line, 'S', old_flowrate)
+ else:
+ if tmp_extruder == 0: #first extruder
+ old_flowrateOne = getValue(line, 'S', old_flowrateOne)
+ if tmp_extruder == 1: #second extruder
+ old_flowrateOne = getValue(line, 'S', old_flowrateOne)
+ if ('M84' in line or 'M25' in line):
+ if state>0 and speed is not None and speed != '': #'finish' commands for UM Original and UM2
+ f.write("M220 S100 ; speed reset to 100% at the end of print\n");
+ f.write("M117 \n")
+ f.write(line)
if 'G1' in line or 'G0' in line:
newZ = getValue(line, 'Z', z)
x = getValue(line, 'X', None)
state = 3
if targetL_i > -100000:
f.write(";TweakAtZ V%s: executed at Layer %d\n" % (version,targetL_i))
+ f.write("M117 Printing... tw@L%4d\n" % targetL_i)
else:
f.write(";TweakAtZ V%s: executed at %1.2f mm\n" % (version,targetZ))
+ f.write("M117 Printing... tw@%5.1f\n" % targetZ)
if speed is not None and speed != '':
f.write("M220 S%f\n" % float(speed))
if flowrate is not None and flowrate != '':
f.write("M221 S%f\n" % float(flowrate))
+ if flowrateOne is not None and flowrateOne != '':
+ f.write("M221 T0 S%f\n" % float(flowrateOne))
+ if flowrateTwo is not None and flowrateTwo != '':
+ f.write("M221 T1 S%f\n" % float(flowrateTwo))
if platformTemp is not None and platformTemp != '':
f.write("M140 S%f\n" % float(platformTemp))
if extruderOne is not None and extruderOne != '':
f.write("M220 S%f\n" % float(old_speed))
if flowrate is not None and flowrate != '':
f.write("M221 S%f\n" % float(old_flowrate))
+ if flowrateOne is not None and flowrateOne != '':
+ f.write("M221 T0 S%f\n" % float(old_flowrateOne))
+ if flowrateTwo is not None and flowrateTwo != '':
+ f.write("M221 T1 S%f\n" % float(old_flowrateTwo))
if platformTemp is not None and platformTemp != '':
f.write("M140 S%f\n" % float(old_platformTemp))
if extruderOne is not None and extruderOne != '':
~ianmdlvl / cura.git / commitdiff