Add raft settings (unused)

diff --git a/Cura/util/profile.py b/Cura/util/profile.py
index ac8d9d16b91e8f3af5acd9cde3c8bacb9b6d3f89..0c7a88d86aa26717d604fe9c081dc436ac331ca5 100644 (file)
--- a/Cura/util/profile.py
+++ b/Cura/util/profile.py
@@ -110,7 +110,7 @@ class setting(object):
 #########################################################
 ## Settings
 #########################################################
-setting('layer_height',              0.2, float, 'basic',    'Quality').setRange(0.0001).setLabel('Layer height (mm)', 'Layer height in millimeters.\n0.2 is a good value for quick prints.\n0.1 gives high quality prints.\nDepending on your printer you can go as low as 0.02mm')
+setting('layer_height',              0.1, float, 'basic',    'Quality').setRange(0.0001).setLabel('Layer height (mm)', 'Layer height in millimeters.\nThis is the most important setting to determen the quality of your print. Normal quality prints are 0.1mm, high quality is 0.06mm. You can go up to 0.25mm with an Ultimaker for very fast prints at low quality.')
 setting('wall_thickness',            0.8, float, 'basic',    'Quality').setRange(0.0001).setLabel('Wall thickness (mm)', 'Thickness of the walls.\nThis is used in combination with the nozzle size to define the number\nof perimeter lines and the thickness of those perimeter lines.')
 setting('retraction_enable',       False, bool,  'basic',    'Quality').setLabel('Enable retraction', 'Retract the filament when the nozzle is moving over a none-printed area. Details about the retraction can be configured in the advanced tab.')
 setting('solid_layer_thickness',     0.6, float, 'basic',    'Fill').setRange(0).setLabel('Bottom/Top thickness (mm)', 'This controls the thickness of the bottom and top layers, the amount of solid layers put down is calculated by the layer thickness and this value.\nHaving this value a multiply of the layer thickness makes sense. And keep it near your wall thickness to make an evenly strong part.')
@@ -163,9 +163,11 @@ setting('solid_bottom', True, bool, 'expert', 'Infill').setLabel('Solid infill b
 #setting('support_distance',  0.5, float, 'expert', 'Support').setRange(0).setLabel('Distance from object (mm)', 'Distance between the support structure and the object. Empty gap in which no support structure is printed.')
 #setting('joris', False, bool, 'expert', 'Joris').setLabel('Spiralize the outer contour', '[Joris] is a code name for smoothing out the Z move of the outer edge. This will create a steady Z increase over the whole print. It is intended to be used with a single walled wall thickness to make cups/vases.')
 #setting('bridge_speed', 100, int, 'expert', 'Bridge').setRange(0,100).setLabel('Bridge speed (%)', 'Speed at which layers with bridges are printed, compared to normal printing speed.')
-#setting('raft_margin', 5, float, 'expert', 'Raft').setRange(0).setLabel('Extra margin (mm)', 'If the raft is enabled, this is the extra raft area around the object which is also rafted. Increasing this margin will create a stronger raft.')
-#setting('raft_base_material_amount', 100, int, 'expert', 'Raft').setRange(0,100).setLabel('Base material amount (%)', 'The base layer is the first layer put down as a raft. This layer has thick strong lines and is put firmly on the bed to prevent warping. This setting adjust the amount of material used for the base layer.')
-#setting('raft_interface_material_amount', 100, int, 'expert', 'Raft').setRange(0,100).setLabel('Interface material amount (%)', 'The interface layer is a weak thin layer between the base layer and the printed object. It is designed to has little material to make it easy to break the base off the printed object. This setting adjusts the amount of material used for the interface layer.')
+setting('raft_margin', 5, float, 'expert', 'Raft').setRange(0).setLabel('Extra margin (mm)', 'If the raft is enabled, this is the extra raft area around the object which is also rafted. Increasing this margin will create a stronger raft while using more material and leaving less are for your print.')
+setting('raft_base_thickness', 0.3, float, 'expert', 'Raft').setRange(0).setLabel('Base thickness (mm)', 'When you are using the raft this is the thickness of the base layer which is put down.')
+setting('raft_base_linewidth', 0.7, float, 'expert', 'Raft').setRange(0).setLabel('Base line width (mm)', 'When you are using the raft this is the width of the base layer lines which are put down.')
+setting('raft_interface_thickness', 0.2, float, 'expert', 'Raft').setRange(0).setLabel('Interface thickness (mm)', 'When you are using the raft this is the thickness of the interface layer which is put down.')
+setting('raft_interface_linewidth', 0.2, float, 'expert', 'Raft').setRange(0).setLabel('Interface line width (mm)', 'When you are using the raft this is the width of the interface layer lines which are put down.')
 setting('brim_line_count', 20, int, 'expert', 'Brim').setRange(1,100).setLabel('Brim line amount', 'The amount of lines used for a brim, more lines means a larger brim which sticks better, but this also makes your effective print area smaller.')
 #setting('hop_on_move', False, bool, 'expert', 'Hop').setLabel('Enable hop on move', 'When moving from print position to print position, raise the printer head 0.2mm so it does not knock off the print (experimental).')