Fixed comments in start/end gcode. Marlin doesn't like () style comments

diff --git a/SkeinPyPy_NewUI/skeinforge_application/alterations/end.gcode b/SkeinPyPy_NewUI/skeinforge_application/alterations/end.gcode
index 64fe937ca3d7d57fe161e234e7ecfb1c32194f88..7d83d9b91d5ea334f6ee0f2f52a6fe9464d1cb22 100644 (file)
--- a/SkeinPyPy_NewUI/skeinforge_application/alterations/end.gcode
+++ b/SkeinPyPy_NewUI/skeinforge_application/alterations/end.gcode
@@ -1,9 +1,7 @@
-(start of end.gcode)
-M104 S0                (extruder heat off)
-M106                   (fan on)
-G91                    (relative positioning)
-G1 Z+10 E-5 F400       (move Z up a bit and retract filament by 5mm)
-G28 X0 Y0              (move X/Y to min endstops, so the head is out of the way)
-M84                    (steppers off)
-G90                    (absolute positioning)
-(end of end.gcode)
+M104 S0                ;extruder heat off
+M106                   ;fan on
+G91                    ;relative positioning
+G1 Z+10 E-5 F400       ;move Z up a bit and retract filament by 5mm
+G28 X0 Y0              ;move X/Y to min endstops, so the head is out of the way
+M84                    ;steppers off
+G90                    ;absolute positioning

diff --git a/SkeinPyPy_NewUI/skeinforge_application/alterations/start.gcode b/SkeinPyPy_NewUI/skeinforge_application/alterations/start.gcode
index 4c30955001ed5b519e541e80e62433b6f4a28868..7c3248d3fe6284b4202cd070a18d77adb5556592 100644 (file)
--- a/SkeinPyPy_NewUI/skeinforge_application/alterations/start.gcode
+++ b/SkeinPyPy_NewUI/skeinforge_application/alterations/start.gcode
@@ -1,29 +1,25 @@
-(start of start.txt)
-G21        (metric values)
+G21        ;metric values)
+G90        ;absolute positioning
 G21
-G21        (all the extra G21 commands are comments - skeinforge eats lines without a gcode)
+G28 X0 Y0  ;move X/Y to min endstops
+G28 Z0     ;move Z to min endstops
+
+; if your prints start too high, try changing the Z0.0 below
+; to Z1.0 - the number after the Z is the actual, physical
+; height of the nozzle in mm. This can take some messing around
+; with to get just right...
 G21
-G90        (absolute positioning)
+G92 X0 Y0 Z0 E0 ;reset software position to front/left/z=0.0
 G21
-G28 X0 Y0  (move X/Y to min endstops)
-G28 Z0     (move Z to min endstops)
+G1 Z15.0 F400  ;move the platform down 15mm
+G92 E0         ;zero the extruded length
 G21
-G21        ( if your prints start too high, try changing the Z0.0 below )
-G21        ( to Z1.0 - the number after the Z is the actual, physical )
-G21        ( height of the nozzle in mm. This can take some messing around )
-G21        ( with to get just right... )
+G1 F75 E5      ;extrude 5mm of feed stock
+G1 F75 E3.5    ;reverse feed stock by 1.5mm
+G92 E0         ;zero the extruded length again
 G21
-G92 X0 Y0 Z0 E0 (reset software position to front/left/z=0.0)
+M1             ;Clean the nozzle then press YES to continue...
 G21
-G1 Z15.0 F400  (move the platform down 15mm)
-G92 E0         (zero the extruded length)
-G21
-G1 F75 E5     (extrude 5mm of feed stock)
-G1 F75 E3.5   (reverse feed stock by 1.5mm)
-G92 E0         (zero the extruded length again)
-G21
-M1             (Clean the nozzle then press YES to continue...)
-G21
-G1 X100 Y100 F3500 (go to the middle of the platform)
-G1 Z0.0 F400   (back to Z=0 and start the print!)
-(end of start.txt)
+G1 X100 Y100 F3500 ;go to the middle of the platform
+G1 Z0.0 F400   ;back to Z=0 and start the print!
+