extruder_amount = 1
[profile]
-filament_diameter = 1.75
+layer_height = 0.20
+wall_thickness = 0.8
+retraction_enable = True
+solid_layer_thickness = 0.6
+fill_density = 15
nozzle_size = 0.4
-layer_height = 0.2
-print_speed = 50
-print_temperature = 240
-travel_speed = 150
+print_speed = 60
+print_temperature = 195
+print_temperature2 = 0
+print_temperature3 = 0
+print_temperature4 = 0
+print_bed_temperature = 60
+support = None
+platform_adhesion = None
+support_dual_extrusion = Both
+wipe_tower = False
+wipe_tower_volume = 15
+ooze_shield = False
+filament_diameter = 1.75
+filament_diameter2 = 0
+filament_diameter3 = 0
+filament_diameter4 = 0
+filament_flow = 100
+retraction_speed = 50.0
+retraction_amount = 0.8
+retraction_dual_amount = 16.5
+retraction_min_travel = 1.5
+retraction_combing = True
+retraction_minimal_extrusion = 0.02
+retraction_hop = 0.075
+bottom_thickness = 0.30
+layer0_width_factor = 100
+object_sink = 0.0
+overlap_dual = 0.15
+travel_speed = 150.0
+bottom_layer_speed = 15
+infill_speed = 0
+inset0_speed = 30
+insetx_speed = 0
+cool_min_layer_time = 5
+fan_enabled = True
+skirt_line_count = 3
+skirt_gap = 4.0
+skirt_minimal_length = 200.0
+fan_full_height = 0.5
+fan_speed = 100
+fan_speed_max = 100
+cool_min_feedrate = 10
+cool_head_lift = False
+solid_top = True
+solid_bottom = True
+fill_overlap = 10
+support_type = Lines
+support_angle = 60
+support_fill_rate = 15
+support_xy_distance = 0.7
+support_z_distance = 0.15
+spiralize = False
+simple_mode = False
+brim_line_count = 20
+raft_margin = 5.0
+raft_line_spacing = 3.0
+raft_base_thickness = 0.3
+raft_base_linewidth = 1.0
+raft_interface_thickness = 0.27
+raft_interface_linewidth = 0.4
+raft_airgap = 0.22
+raft_surface_layers = 2
+fix_horrible_union_all_type_a = True
+fix_horrible_union_all_type_b = False
+fix_horrible_use_open_bits = False
+fix_horrible_extensive_stitching = False
+plugin_config =
+object_center_x = -1
+object_center_y = -1
+
+[alterations]
+start.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M109 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M82 ;set extruder to absolute mode
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ M205 X8 ;X/Y Jerk settings
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ G92 E0 ;zero the extruded length
+ G1 F200 E7 ;extrude 3mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Rigibot Printing...
+end.gcode = ;End GCode
+ M104 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+10 E-1 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ G1 Y230 F3000 ;move Y so the head is out of the way and Plate is moved forward
+ M84 ;steppers off
+ G90 ;absolute positioning
+ ;{profile_string}
+start2.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M104 S{print_temperature} ;Uncomment to add your own temperature line
+ ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ T1 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T0 ;Switch to the first extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Printing...
+end2.gcode = ;End GCode
+ M104 T0 S0 ;extruder heater off
+ M104 T1 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ M84 ;steppers off
+ G90 ;absolute positioning
+ ;{profile_string}
+start3.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M104 S{print_temperature} ;Uncomment to add your own temperature line
+ ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ T2 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T1 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T0 ;Switch to the first extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Printing...
+end3.gcode = ;End GCode
+ M104 T0 S0 ;extruder heater off
+ M104 T1 S0 ;extruder heater off
+ M104 T2 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ M84 ;steppers off
+ G90 ;absolute positioning
+ ;{profile_string}
+start4.gcode = ;Sliced at: {day} {date} {time}
+ ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+ ;Print time: {print_time}
+ ;Filament used: {filament_amount}m {filament_weight}g
+ ;Filament cost: {filament_cost}
+ ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+ ;M104 S{print_temperature} ;Uncomment to add your own temperature line
+ ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
+ ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
+ G21 ;metric values
+ G90 ;absolute positioning
+ M107 ;start with the fan off
+ G28 X0 Y0 ;move X/Y to min endstops
+ G28 Z0 ;move Z to min endstops
+ G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+ T3 ;Switch to the 4th extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T2 ;Switch to the 3th extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T1 ;Switch to the 2nd extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F200 E-{retraction_dual_amount}
+ T0 ;Switch to the first extruder
+ G92 E0 ;zero the extruded length
+ G1 F200 E10 ;extrude 10mm of feed stock
+ G92 E0 ;zero the extruded length again
+ G1 F{travel_speed}
+ ;Put printing message on LCD screen
+ M117 Printing...
+end4.gcode = ;End GCode
+ M104 T0 S0 ;extruder heater off
+ M104 T1 S0 ;extruder heater off
+ M104 T2 S0 ;extruder heater off
+ M104 T3 S0 ;extruder heater off
+ M140 S0 ;heated bed heater off (if you have it)
+ G91 ;relative positioning
+ G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+ G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+ G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
+ M84 ;steppers off
+ G90 ;absolute positioning
~ianmdlvl / cura.git / commitdiff