// Access from ARM Running Linux
// Taken from Gert/Doms code. Some of this is not in the manual
// that I can find )-:
+//
+// Updates in September 2015 - all now static variables (and apologies for the caps)
+// due to the Pi v2 and the new /dev/gpiomem interface
-static volatile unsigned int BCM2708_PERI_BASE = 0x20000000 ; // Variable for Pi2
-#define GPIO_PADS (BCM2708_PERI_BASE + 0x00100000)
-#define CLOCK_BASE (BCM2708_PERI_BASE + 0x00101000)
-#define GPIO_BASE (BCM2708_PERI_BASE + 0x00200000)
-#define GPIO_TIMER (BCM2708_PERI_BASE + 0x0000B000)
-#define GPIO_PWM (BCM2708_PERI_BASE + 0x0020C000)
+static volatile unsigned int RASPBERRY_PI_PERI_BASE ;
+static volatile unsigned int GPIO_PADS ;
+static volatile unsigned int GPIO_CLOCK_BASE ;
+static volatile unsigned int GPIO_BASE ;
+static volatile unsigned int GPIO_TIMER ;
+static volatile unsigned int GPIO_PWM ;
#define PAGE_SIZE (4*1024)
#define BLOCK_SIZE (4*1024)
* 0010 - Model B+, Rev 1.2, 512MB, Sony
* 0011 - Pi CM, Rev 1.2, 512MB, Sony
* 0012 - Model A+ Rev 1.2, 256MB, Sony
+ * 0014 - Pi CM, Rev 1.1, 512MB, Sony (Actual Revision might be different)
+ * 0015 - Model A+ Rev 1.1, 256MB, Sony
*
* For the Pi 2:
* 0010 - Model 2, Rev 1.1, Quad Core, 1GB, Sony
* last digit, then it's 1, therefore it'll default to not 2 or 3 for a
* Rev 1, so will appear as a Rev 2. This is fine for the most part, but
* we'll properly detect the Compute Module later and adjust accordingly.
+ * And the next rev of the CN is 0014 ...
*
*********************************************************************************
*/
else if (strstr (line, "BCM2708") == NULL)
{
fprintf (stderr, "Unable to determine hardware version. I see: %s,\n", line) ;
- fprintf (stderr, " - expecting BCM2708 or BCM2709. Please report this to projects@drogon.net\n") ;
+ fprintf (stderr, " - expecting BCM2708 or BCM2709.\n") ;
+ fprintf (stderr, "If this is a genuine Raspberry Pi then please report this\n") ;
+ fprintf (stderr, "to projects@drogon.net. If this is not a Raspberry Pi then you\n") ;
+ fprintf (stderr, "are on your own as wiringPi is designed to support the\n") ;
+ fprintf (stderr, "Raspberry Pi ONLY.\n") ;
exit (EXIT_FAILURE) ;
}
if ( (strcmp (c, "0002") == 0) || (strcmp (c, "0003") == 0))
boardRev = 1 ;
else
- boardRev = 2 ;
+ boardRev = 2 ; // Covers everything else from the B revision 2 to the B+, the Pi v2 and CM's.
if (wiringPiDebug)
printf ("piBoardRev: Returning revision: %d\n", boardRev) ;
break ;
if (*c != ':')
- piBoardRevOops ("Bogus \"Revision\" line") ;
+ piBoardRevOops ("Bogus \"Revision\" line (no colon)") ;
// modelNum = (unsigned int)strtol (++c, NULL, 16) ; // Hex number with no leading 0x
// Make sure its long enough
if (strlen (c) < 4)
- piBoardRevOops ("Bogus \"Revision\" line") ;
+ piBoardRevOops ("Bogus \"Revision\" line (not long enough)") ;
// If longer than 4, we'll assume it's been overvolted
else if (strcmp (c, "0011") == 0) { *model = PI_MODEL_CM ; *rev = PI_VERSION_1_2 ; *mem = 512 ; *maker = PI_MAKER_SONY ; }
else if (strcmp (c, "0012") == 0) { *model = PI_MODEL_AP ; *rev = PI_VERSION_1_2 ; *mem = 256 ; *maker = PI_MAKER_SONY ; }
else if (strcmp (c, "0013") == 0) { *model = PI_MODEL_BP ; *rev = PI_VERSION_1_2 ; *mem = 512 ; *maker = PI_MAKER_MBEST ; }
+ else if (strcmp (c, "0014") == 0) { *model = PI_MODEL_CM ; *rev = PI_VERSION_1_2 ; *mem = 512 ; *maker = PI_MAKER_SONY ; }
+ else if (strcmp (c, "0015") == 0) { *model = PI_MODEL_AP ; *rev = PI_VERSION_1_1 ; *mem = 256 ; *maker = PI_MAKER_SONY ; }
else { *model = 0 ; *rev = 0 ; *mem = 0 ; *maker = 0 ; }
}
}
if (getenv (ENV_CODES) != NULL)
wiringPiReturnCodes = TRUE ;
- if (geteuid () != 0)
- (void)wiringPiFailure (WPI_FATAL, "wiringPiSetup: Must be root. (Did you forget sudo?)\n") ;
-
if (wiringPiDebug)
printf ("wiringPi: wiringPiSetup called\n") ;
}
else // A, B, Rev 2, B+, CM, Pi2
{
- if (piModel2)
- BCM2708_PERI_BASE = 0x3F000000 ;
pinToGpio = pinToGpioR2 ;
physToGpio = physToGpioR2 ;
}
-// Open the master /dev/memory device
+ if (piModel2)
+ RASPBERRY_PI_PERI_BASE = 0x3F000000 ;
+ else
+ RASPBERRY_PI_PERI_BASE = 0x20000000 ;
+
+// Open the master /dev/ memory control device
+
+// See if /dev/gpiomem exists and we can open it...
+
+ if ((fd = open ("/dev/gpiomem", O_RDWR | O_SYNC | O_CLOEXEC) ) >= 0)
+ RASPBERRY_PI_PERI_BASE = 0 ;
+
+// ... otherwise fall back to the original /dev/mem which requires root level access
+
+ else
+ {
+
+// This check is here because people are too stupid to check for themselves or read
+// error messages.
+
+ if (geteuid () != 0)
+ (void)wiringPiFailure (WPI_FATAL, "wiringPiSetup: Must be root. (Did you forget sudo?)\n") ;
+
+ if ((fd = open ("/dev/mem", O_RDWR | O_SYNC | O_CLOEXEC) ) < 0)
+ return wiringPiFailure (WPI_ALMOST, "wiringPiSetup: Unable to open /dev/mem: %s\n", strerror (errno)) ;
+ }
+
+// Set the offsets into the memory interface.
- if ((fd = open ("/dev/mem", O_RDWR | O_SYNC | O_CLOEXEC) ) < 0)
- return wiringPiFailure (WPI_ALMOST, "wiringPiSetup: Unable to open /dev/mem: %s\n", strerror (errno)) ;
+ GPIO_PADS = RASPBERRY_PI_PERI_BASE + 0x00100000 ;
+ GPIO_CLOCK_BASE = RASPBERRY_PI_PERI_BASE + 0x00101000 ;
+ GPIO_BASE = RASPBERRY_PI_PERI_BASE + 0x00200000 ;
+ GPIO_TIMER = RASPBERRY_PI_PERI_BASE + 0x0000B000 ;
+ GPIO_PWM = RASPBERRY_PI_PERI_BASE + 0x0020C000 ;
-// GPIO:
+// Map the individual hardware components
+
+// GPIO:
gpio = (uint32_t *)mmap(0, BLOCK_SIZE, PROT_READ|PROT_WRITE, MAP_SHARED, fd, GPIO_BASE) ;
if ((int32_t)gpio == -1)
return wiringPiFailure (WPI_ALMOST, "wiringPiSetup: mmap (GPIO) failed: %s\n", strerror (errno)) ;
-// PWM
+// PWM
pwm = (uint32_t *)mmap(0, BLOCK_SIZE, PROT_READ|PROT_WRITE, MAP_SHARED, fd, GPIO_PWM) ;
if ((int32_t)pwm == -1)
return wiringPiFailure (WPI_ALMOST, "wiringPiSetup: mmap (PWM) failed: %s\n", strerror (errno)) ;
-// Clock control (needed for PWM)
+// Clock control (needed for PWM)
- clk = (uint32_t *)mmap(0, BLOCK_SIZE, PROT_READ|PROT_WRITE, MAP_SHARED, fd, CLOCK_BASE) ;
+ clk = (uint32_t *)mmap(0, BLOCK_SIZE, PROT_READ|PROT_WRITE, MAP_SHARED, fd, GPIO_CLOCK_BASE) ;
if ((int32_t)clk == -1)
return wiringPiFailure (WPI_ALMOST, "wiringPiSetup: mmap (CLOCK) failed: %s\n", strerror (errno)) ;
-// The drive pads
+// The drive pads
pads = (uint32_t *)mmap(0, BLOCK_SIZE, PROT_READ|PROT_WRITE, MAP_SHARED, fd, GPIO_PADS) ;
if ((int32_t)pads == -1)
return wiringPiFailure (WPI_ALMOST, "wiringPiSetup: mmap (PADS) failed: %s\n", strerror (errno)) ;
#ifdef USE_TIMER
-// The system timer
+// The system timer
timer = (uint32_t *)mmap(0, BLOCK_SIZE, PROT_READ|PROT_WRITE, MAP_SHARED, fd, GPIO_TIMER) ;
if ((int32_t)timer == -1)