// -*- C -*-
+coarse = false;
+
main_dia = 71.2 + 0.50 - 2.26;
-top_thick = 4;
+top_thick_middle = 4;
+top_thick_by_oring = 3.0;
+top_middle_dr = 11;
+
+main_cnr = 6.0;
-main_cnr = 4.0;
+min_wall = 3;
-rivet_posn = 6.0;
+rivet_posn = 6.0 + 0.30;
rivet_thick = 1.67;
rivet_width = 4.15 + 1.0;
-rivet_tall = 5.51 + 0.49;
+rivet_tall = 5.51 + 1.49;
-over_rivet_wall = 0.5;
+over_rivet_wall = 1.0;
side_rivet_gap = 1.5;
+inside_rivet_gap = 1.5;
-bayo_interf = 1.25;
+bayo_interf = 0.30;
bayo_behind = 3.5;
bayo_interf_width = 2.0;
-bayo_interf_slope = 0.75;
+bayo_interf_slope = 0.5;
oring_thick = 5.0;
oring_bore = 62.0;
oring_upper_embed_angle = 80;
oring_compress = 0.1; // proportion
+oring_compress_more = 0.2;
+
+oring_rm_beside = 8;
+oring_rm_scale = 2.0;
+oring_rm_angle = 20;
side_taper = 1.0;
-bayo_above_gap = 1.0;
+bayo_gap = 6.0;
bayo_entry = bayo_behind/3;
-bayo_slice_size = 1;
+bayo_slice_size = coarse ? 5 : 1;
brace_hole_width = 1.0;
brace_above_below = 1.2;
jig_rim = 5;
jig_mark = 5;
+strap_hoop_thick = 6;
+strap_hoop_inside = 10;
+strap_hoop_strlen = 10;
+strap_hoop_elevation = 45;
+
+sm_inner_circum = 218 - 1.90 - 1.00 - 0.50;
+sm_main_thick = 2.0;
+sm_main_width = 20;
+
+sm_bolt_dia = 3.5 + 0.1;
+sm_bolt_shaft = 21.9;
+sm_bolt_head_dia = 6.94 + 1.0;
+sm_bolt_head_thick = 2.14;
+sm_bolt_nut_width = 5.89 + 0.25;
+sm_bolt_nut_thick = 3.68;
+sm_bolt_tighten_allow = 2.0;
+
+sm_bolt_y_clear = 0.75;
+sm_bolt_y_over = 0.5;
+
+sm_closure_cnr = 3.0;
+
+catch_stem_h = 3;
+catch_stem_len = 50;
+catch_stem_th = 3;
+
+catch_pin_slop = 0.25; // each side, and above
+catch_stalk_above_gap = 1.5;
+catch_stalk_eff_bend_rad = catch_stem_len * 0.75;
+
+catch_stalk_base_width = 15;
+
+catch_knob_dia = 6;
+catch_knob_above_gap = 8;
+catch_knob_height = 6;
+
+catch_stem_below_gap = 1.0;
+catch_stem_beside_gap = 2.0;
+catch_pin_gap = 0.5;
+catch_hook_slope = 0.15;
+
// calculated
+TAU = PI*2;
+
bayo_entry_x = bayo_entry;
bayo_entry_z = bayo_entry;
bayo_inramp_x = bayo_entry;
oring_y_rad = oring_thick/2 * oring_oblate;
oring_x_rad = oring_thick/2 / oring_oblate;
-seal_thick = oring_y_rad * (1 + cos(oring_upper_embed_angle));
+by_oring_z = oring_y_rad * (1 + cos(oring_upper_embed_angle));
side_height = rivet_posn + bayo_behind + rivet_thick/2;
side_thick = rivet_tall + over_rivet_wall;
-top_z = top_thick + seal_thick;
+top_z = top_thick_by_oring + oring_y_rad + by_oring_z;
+
+middle_bot_z = top_z - top_thick_middle;
bayo_entry = bayo_behind / 3.0;
-bayo_top_z = bayo_behind + rivet_thick + bayo_above_gap;
-bayo_entry_ramp = bayo_entry + bayo_interf;
+bayo_top_z = bayo_behind + bayo_gap;
+
+bayo_nom_rad = main_dia/2 + side_thick;
+bayo_real_rad = main_dia/2 + rivet_tall;
rivet_entry_width = rivet_width + side_rivet_gap;
jig_mark_rad = jig_mark + main_dia/2 + jig_thick;
-$fs=0.5;
-$fa=1;
+handling_dia = oring_bore + oring_thick*2 + min_wall*2;
+handling_angle = 45;
+
+sm_inner_rad = (sm_inner_circum + sm_bolt_tighten_allow/2) / TAU;
+sm_outer_rad = sm_inner_rad + sm_main_thick;
+
+smc_pos = [ 0, sm_inner_rad, 0 ];
+
+smc_bolt_nut_dia = sm_bolt_nut_width / cos(30);
+smc_bolt_nut_eff_thick = sm_bolt_nut_thick + sm_bolt_tighten_allow;
+
+smc_bolt_y = sm_bolt_dia/2 + sm_bolt_y_clear;
+smc_max_y = smc_bolt_y + sm_bolt_y_over
+ + max(sm_bolt_head_dia/2, smc_bolt_nut_dia/2);
+smc_cnr_c_x = sm_bolt_shaft/2 - sm_closure_cnr
+ + sm_bolt_head_thick/2 + smc_bolt_nut_eff_thick/2;
+
+catch_cr = catch_knob_dia/2 + catch_stem_beside_gap;
+catch_strap_width = sm_main_width;
+catch_strap_thick = sm_main_thick;
+catch_stem_end_h = catch_stem_h;
+catch_pin_width = (rivet_entry_width * sm_inner_rad / bayo_nom_rad)
+ - catch_pin_gap;
+
+echo("R ", sm_inner_rad, bayo_real_rad, bayo_nom_rad);
+
+$fs= coarse ? 2.5 : 0.5;
+$fa= coarse ? 5 : 1;
+
+include <poster-tube-lid-parametric.scad>
// bayonet definition
bayo_l = bayo_m + bayo_interf * [ 1/bayo_interf_slope, 1 ];
bayo_k = bayo_l + [ bayo_interf_width, 0 ];
bayo_j = bayo_k + bayo_interf * [ 1/bayo_interf_slope, -1 ];
-bayo_i = bayo_j + [ rivet_width, 0 ];
-bayo_h = [ bayo_i[0], bayo_behind + rivet_thick
- + bayo_above_gap + bayo_interf ];
+bayo_i = bayo_j + [ rivet_width + inside_rivet_gap, 0 ];
+bayo_h = [ bayo_i[0], bayo_behind + bayo_gap + bayo_interf ];
bayo_g = [ bayo_m[0] - rivet_width, bayo_h[1] ];
bayo_e = [-bayo_p[0], bayo_p[1]] - [rivet_entry_width,0];
echo(bayo_polygon);
+// CATCH
+
+//cppy6 = -catch_strap_width * 2/3;
+
+cppxC = 0.34 * sm_inner_rad * TAU;
+
+// catch pin
+
+cppa = bayo_f + [1,-1] * catch_pin_slop;
+cppb = bayo_g + [1,-1] * catch_pin_slop;
+cppd = [ bayo_n[0] - catch_pin_slop, -catch_stalk_above_gap ];
+cppc = [ cppd[0], cppb[1] ];
+cpph = cppd + [0,-1] * catch_stem_h;
+cppe = cppd + [0,-1] * (catch_knob_above_gap + catch_knob_dia/2);
+cppf = [ cppa[0], cppe[1] ];
+cppg = [ cppa[0], cpph[1] ];
+cppB = 0.5 * (cppf + cppe);
+
+// catch assembly depression below pin
+
+cppy6 = cppB[1] - (catch_knob_dia/2
+ + (cppc[1] - cppd[1])
+ + catch_stem_below_gap);
+cpp7 = [ cppB[0], cppy6 + catch_cr ];
+cpp11 = cpp7 + [1,0] * catch_cr;
+cppy9 = cppy6 + catch_strap_width * 1/3;
+cpp9 = [ cpp7[0] + catch_cr * 2, cppy9 ];
+cpp8 = cpp9 + [0,-1] * catch_cr;
+cpp10 = cpp8 + [-1,0] * catch_cr;
+cppC = [ cppxC, cpp9[1] ];
+cppD = cppC + [0,-1] * catch_strap_width;
+
+// catch assembly stalk and so on
+
+cppF = [ cppg[0] - catch_stem_stalk_eff_bend_rad, cppd[1] ];
+cpp4 = [ cppg[0] - catch_stem_lenm, cppd[1] ] + [1,-1] * catch_cr;
+cpp5 = [ cpp4[0], cppC[1] + catch_cr ];
+cpp2 = cpp5 + [-1,0] * (catch_cr * 2 + catch_stalk_base_width);
+cpp3 = [ cpp2[0] + catch_cr * 2, cppd[1] - catch_cr ];
+cppA = [ -cppxC, cpp9[1] ];
+cppE = [ cppA[0], cppD[1] ];
+
+
module MainProfile(){
main_cnr_pos = [ side_thick, top_z ] - [1,1]*main_cnr;
difference(){
square([10,10]);
}
}
- polygon([[ -11, seal_thick ],
- [ -11, top_z ],
+ polygon([[ -top_middle_dr, middle_bot_z ],
+ [ -top_middle_dr, top_z ],
[ main_cnr_pos[0], top_z ],
[ side_thick, main_cnr_pos[1] ],
[ side_thick, -side_height ],
[ side_taper, -side_height ],
[ 0, -rivet_posn ],
- [ 0, seal_thick ],
+ [ 0, by_oring_z ],
+ [ -oring_x_rad, by_oring_z ],
],
convexity=10);
}
translate([ oring_mid_dia/2 - main_dia/2, 0 ])
hull(){
translate([ 0, oring_y_rad ])
- scale([ 1/oring_oblate, oring_oblate ])
+ scale([ 1/oring_oblate * (oring_compress_more+1) , oring_oblate ])
circle(oring_thick/2);
translate([ 0, oring_y_rad*2 - oring_thick/2 ])
circle(oring_thick/2);
}
}
+module StrapHoopProfile(){
+ circle(r = strap_hoop_thick/2);
+}
+
+module StrapHoop(){ ////toplevel
+ bigrad = strap_hoop_inside/2 + strap_hoop_thick/2;
+ extralen = strap_hoop_thick * 5;
+
+ intersection(){
+ rotate([strap_hoop_elevation, 0,0]){
+ for (x= [ -1, +1 ] * bigrad) {
+ translate([x, -extralen, 0])
+ rotate([-90,0,0])
+ linear_extrude(height= extralen + strap_hoop_strlen + 0.1,
+ convexity=10)
+ StrapHoopProfile();
+ }
+ translate([0, strap_hoop_strlen, 0]){
+ intersection(){
+ rotate_extrude(convexity=10)
+ translate([bigrad, 0,0])
+ StrapHoopProfile();
+ translate([0,50,0])
+ cube([100,100,100], center=true);
+ }
+ }
+ }
+ translate([0, 50, 0])
+ cube(100, center=true);
+ }
+}
+
module RotateProjectSlice(offset, slice_size, nom_rad, real_rad){
// nom_rad > real_rad
rotate([0,0, atan2(offset, nom_rad) ]){
module BayonetCutout(){
RotateProject(bayo_c[0], bayo_i[0], bayo_slice_size,
- main_dia/2 + side_thick,
- main_dia/2 + rivet_tall)
+ bayo_nom_rad,
+ bayo_real_rad)
+ translate([-0.5 * (bayo_a[0] + bayo_d[0]), 0])
polygon(bayo_polygon, convexity=10);
}
module ProfilesDemo(){ ////toplevel
- translate([-20,0]) MainProfile();
- polygon(bayo_polygon, convexity=10);
+ translate([-10,0]) MainProfile();
+ translate([+10, -side_height]) polygon(bayo_polygon, convexity=10);
+}
+
+module LimitForHandling(){ ////toplevel
+ hull() for (r=[0,180])
+ rotate([0,0,r]) {
+ for (rs=[-1,+1]) {
+ for (xd=[0,1]) {
+ rotate([0,0, rs * handling_angle/2]) {
+ translate([rs * xd * main_dia/2 * tan(handling_angle/2),
+ main_dia/2 + side_thick - main_cnr,
+ top_z - main_cnr]) {
+ mirror([0,0,1])
+ cylinder(r= main_cnr, h=50);
+ sphere(main_cnr);
+ }
+ }
+ }
+ }
+ }
+ hull() rotate_extrude(){
+ translate([ handling_dia/2 - main_cnr, top_z - main_cnr ]) {
+ circle(r = main_cnr);
+ mirror([0,1]) square([ main_cnr, 50 ]);
+ }
+ }
+ //cylinder(r= handling_dia/2, h=20);
}
module Cover(){ ////toplevel
render() difference(){
- union(){
- rotate_extrude(convexity=10)
- translate([main_dia/2, 0])
- MainProfile();
- translate([0,0, seal_thick])
- cylinder(h= top_thick, r = main_dia/2 - 10);
+ intersection(){
+ union(){
+ rotate_extrude(convexity=10)
+ translate([main_dia/2, 0])
+ MainProfile();
+ translate([0,0, middle_bot_z])
+ cylinder(h= top_thick_middle, r = main_dia/2 - top_middle_dr + 1);
+ }
+ LimitForHandling();
}
- for (r=[0,180])
+ for (r=[0,180]){
rotate([0,0, r])
translate([0,0, -side_height])
BayonetCutout();
+ rotate([0,0, r + asin((-oring_rm_beside) / (main_dia/2))])
+ translate([0,
+ oring_mid_dia/2 + oring_thick/4 * oring_rm_scale,
+ oring_y_rad * 1.5])
+ rotate([-oring_rm_angle, 0, 0])
+ mirror([0,0,1])
+ cylinder(r = oring_thick/4 * oring_rm_scale, h=20);
+ }
for (r=[0 : 60 : 179]) {
rotate([0,0, r]) {
- height = top_thick - brace_above_below*2;
- translate([0,0, seal_thick + brace_above_below + height/2 ])
+ height = top_thick_middle - brace_above_below*2;
+ translate([0,0, middle_bot_z + brace_above_below + height/2 ])
cube(center=true, [ oring_bore - brace_end_shorter,
brace_hole_width, height ]);
}
}
}
+ for (r=[0,180])
+ rotate([0,0,r])
+ translate([-implheadcup_large_dia * .5 - implheadcup_thick/2,
+ -implheadcup_large_dia * .0,
+ middle_bot_z + 0.1])
+ ImplHeadCup();
+// translate(strap_hoop_thick * [-0.5, 0, +1])
+// translate([handling_dia/2, 0, -side_height])
+// rotate([0,180,0]) rotate([0,0,90])
+// StrapHoop();
}
module SavingHole(){
module CoverTest1(){ ////toplevel
difference(){
CoverTest2();
- translate([0,0, -10])
- cube([ main_dia*3, main_dia * .85, 20], center=true);
+ difference(){
+ for (r= [ 40, 147 ]){
+ rotate([0,0, r]){
+ translate([0,0, -10]) {
+ cube([ main_dia*3, main_dia * .53, 18], center=true);
+ }
+ }
+ }
+// translate([ 50, 0, 0 ])
+// cube([ 100,
+// strap_hoop_inside + strap_hoop_thick*2 + 1,
+// 100 ],
+// center=true);
+ }
+ }
+}
+
+module ImplHeadCupTest(){ ////toplevel
+ for (r=[0,180])
+ rotate([0,0,r])
+ translate([-17,0,0])
+ ImplHeadCup();
+}
+
+module SomeStrap(){
+ // children(0) is to add, (1) subtract
+ difference(){
+ union(){
+ cylinder(r=sm_outer_rad, h=sm_main_width);
+ StrapMountProtrusion(smc_cnr_c_x + sm_closure_cnr,
+ smc_max_y,
+ sm_closure_cnr);
+ children(0);
+ }
+ translate([0,0,-1])
+ cylinder(r=sm_inner_rad, h=sm_main_width+2);
+ translate(smc_pos)
+ StrapMountBolt(10);
+ translate(smc_pos)
+ cube([ sm_bolt_tighten_allow, 40,100 ], center=true);
+ children(1);
+ }
+}
+
+module StrapMountBolt(l_delta){ ///toplevel
+ // positioned relative to smc_pos
+ translate([(smc_bolt_nut_eff_thick - sm_bolt_head_thick)/2,
+ smc_bolt_y,
+ sm_main_width/2]){
+ translate([ -sm_bolt_shaft/2-1, 0,0 ]){
+ rotate([0,90,0]) cylinder(r= sm_bolt_dia/2, h= sm_bolt_shaft+2);
+ }
+ translate([ -sm_bolt_shaft/2, 0,0 ])
+ rotate([0,-90,0])
+ cylinder($fn=6, r=smc_bolt_nut_dia/2,
+ h=smc_bolt_nut_eff_thick + l_delta);
+ translate([ sm_bolt_shaft/2, 0,0 ])
+ rotate([0,90,0])
+ cylinder(r=sm_bolt_head_dia/2, h=sm_bolt_head_thick + l_delta);
+ }
+}
+
+module StrapMountProtrusion(half_x, max_y, cnr){
+ translate(smc_pos){
+ linear_extrude(height=sm_main_width, convexity=10){
+ hull(){
+ for (m = [0,1]) mirror([m,0,0]) {
+ translate([-(half_x - cnr), max_y - cnr])
+ circle(r=cnr);
+ translate([-half_x, -sm_inner_rad])
+ square([1,1]);
+ }
+ }
+ }
+ }
+}
+
+module StrapMount(){ ////toplevel
+ SomeStrap(){
+ rotate([0,0,180]){
+ StrapMountProtrusion(strap_hoop_inside/2 + strap_hoop_thick,
+ strap_hoop_thick,
+ sm_closure_cnr);
+ translate(smc_pos +
+ [0,0, sm_main_width] +
+ strap_hoop_thick * [ 0, 0.5, -1.0 ])
+ StrapHoop();
+ }
+ union(){ };
}
}
+module CatchCoreProfile(){ ////toplevel
+ hull(){
+ translate(cppB) circle(r= catch_knob_dia/2);
+ polygon([cpp4,
+ cppB,
+ cpp3]);
+ }
+ translate(cpp8)
+ circle(catch_cr);
+ polygon([
+ cpp4,
+ cppB,
+ cpp3,
+ cpp2,
+ cpp1,
+ cpp12,
+ ]);
+ difference(){
+ polygon([ cpp4,
+ cpp3,
+ cpp12,
+ cppA,
+ cppE,
+ cppD,
+ cppC,
+ cpp9,
+ cpp10,
+ cpp11,
+ cpp7,
+ cpp5,
+ ], convexity=10);
+ hull(){
+ translate(cpp7) circle(r= catch_cr);
+ polygon([ cpp7,
+ cpp5,
+ cpp11 ]);
+ }
+ hull(){
+ translate(cpp6) circle(catch_cr);
+ polygon([ cppA,
+ cpp0,
+ cpp1 ]);
+ }
+ }
+}
+
+module CatchCore(){ /////toplevel
+ linear_extrude(height=catch_strap_thick, convexity=10)
+ CatchCoreProfile();
+
+ translate(concat(cppB,[0])) hull(){
+ translate([0,0, catch_knob_height - catch_knob_dia/2])
+ sphere(r = catch_knob_dia/2);
+ cylinder(r = catch_knob_dia/2, h = 0.1);
+ }
+}
+
+module CatchPreDistort(){ /////toplevel
+ scale(100 / sm_inner_rad)
+ rotate([90,0,0])
+ CatchCore();
+}
+
+module CatchAssembly(){ /////toplevel
+ rotate([0,0, -0.5 * (cpp1[0] + cpp2[0]) / sm_inner_rad * 360/TAU])
+ translate([0,0, catch_strap_width])
+ scale(sm_inner_rad / 100)
+ import(str("poster-tube-lid,CatchPostDistort-fa",
+ (coarse ? 20 : 3),
+ ".stl"),
+ convexity=20);
+
+ SomeStrap(){
+ union(){ }
+ union(){
+ translate([-200, -200, -200])
+ cube([400, 200, 400]);
+ }
+ }
+}
+
+module CatchDemo(){ /////toplevel
+ color("blue") translate([0,0,
+ -catch_strap_width
+ -cpp0[1]
+ ])
+ CatchAssembly();
+ translate([0,0,+side_height
+ ])
+ Cover();
+}
+
+module CatchDemoS(){ /////toplevel
+ color("blue") translate([0,0,
+ -catch_strap_width
+ -cpp0[1]
+ ])
+ CatchAssembly();
+ intersection(){
+ translate([0,0,+side_height
+ ])
+ Cover();
+ mirror([0,1,0]) translate([-250,33,0]) cube([500,500,500]);
+ }
+ color("black")
+ translate([0,-33,0])
+ cube([6.15, 2,2], center=true);
+}
+
+module CatchPinProfileDemo(){ /////toplevel
+ echo("G ",
+ cpp2[0] - cpp1[0],
+ bayo_n[0] - bayo_e[0]);
+ color("blue") translate([-cpp2[0],
+ -cpp2[1],
+ +1,
+ ])
+ CatchCoreProfile();
+ polygon(bayo_polygon, convexity=10);
+}
+
//ProfilesDemo();
//BayonetCutout();
//MainProfile();