// -*- C -*-
-phone_height = 146.5;
-phone_width = 76.75;
+phone = [ 75.0, 145.0 ];
+
+bumper = [ 0.250, 0.250 ];
+// ^ One side. Overall size is increased by twice this.
+// If no bumpers, is the gap around the phone.
phone_cnr_rad = 6.0;
phone_backside_slope_inner = 1.5; // larger means shallower
phone_backside_slope_outer = 1.0; // larger means shallower
-camera_pos_tl = [ 7.0, 13.0 ]; // measured from tl corner
-camera_pos_br = [ 22.85,37.85]; // tl/br as seen from back
+camera_pos_tl = [ 6.450, 12.750 ]; // measured from tl corner
+camera_pos_br = [ 22.300, 37.600 ]; // tl/br as seen from back
+
+jack_pos = [ 13.92, 7.96 ];
+jack_dia = 9.1 + .5; // some jack I had lying around
+
+noisecancelmic_pos = [ 19.54, 7.37 ]; // from rhs
+noisecancelmic_dia = 1.75;
+
+rearspeaker_pos_bl = [ 14.92, 18.72 ];
+rearspeaker_size = [ 3.76, 7.36 ];
case_th_bottom = 2.5;
case_th_lid = 2.5;
$fa = 5;
$fs = 0.1;
-button_l_fudge = 4.5;
+button_l_fudge = 4.4;
+buttonishleg_default_l_is_fudge = 10;
strut_min_at_end = 1.5;
+rearspeaker_gap = [ 1.0, 1.0 ]; // each side
+
// ---------- calculated ----------
+phone_width = (phone + bumper*2)[0];
+phone_height = (phone + bumper*2)[1];
+
+inside_br = [phone_width, -phone_height];
+
+//echo(camera_pos_tl + bumper,
+// camera_pos_br + bumper);
+
// ----- could be changed -----
lid_buttoncover_gap = lid_gap_x;
lid_buttoncover_overlap = case_th_lip + keeper_gap_z_top;
lpp12 = [ epp4[0] + lp_r12, lpp11[1] ];
lpp13 = [ lpp12[0], lpp12[1] + lp_r12 ];
-echo(lpp13 - lpp10);
-
// button profile
bppM = epp4 + [0,5];
bppN = [ 0.5 * (epp0[0] + epp4[0]), bppM[1] ];
square([abs(ab[0]), abs(ab[1])]);
}
module circleat(c,r) { translate(c) circle(r); }
+module linextr(z0,z1) {
+ translate([0,0,z0])
+ linear_extrude(height=z1-z0)
+ children();
+}
module KeeperProfile(slant=0){
use_e = kppe + [0,-1] * slant * keeper_inner_width / keeper_slant_slope;
}
module CaseBase_rhsflip(yn=[0,1]) {
- for (rhs=yn) {
+ for ($rhsflip=yn) {
translate([phone_width/2, 0, 0])
- mirror([rhs,0,0])
+ mirror([$rhsflip,0,0])
translate([-phone_width/2, 0, 0])
children();
}
}
-module CaseBase_botflip() {
- for (bot=[0,1]) {
+module CaseBase_botflip(yn=[0,1]) {
+ for ($botflip=yn) {
translate([0, -phone_height/2, 0])
- mirror([0, bot, 0])
+ mirror([0, $botflip, 0])
translate([0, phone_height/2, 0])
children();
}
[phone_width, -phone_height] + [-1,+1] * phone_cnr_rad);
}
-module SideButton(y,l){
+module CaseAperture(pos, dia, $fn) {
+ theta = 180/$fn;
+ translate([ pos[0] + bumper[0],
+ -epp2i[0],
+ -pos[1] ])
+ rotate([-90, theta, 0])
+ cylinder(r = dia/2 / cos(theta),
+ h = 60);
+}
+
+module SideButton(y, y_ref_sign, l){
+ // y_ref_sign:
+ // +1 measured from top of actual phone to top of button
+ // -1 measured from bottom of actual phone to bottom of button
+ // 0 y is centre of button in coordinate system
$button_l= l;
- translate([0, -y, 0])
+ eff_y = y_ref_sign > 0 ? -bumper [1] -y -l/2 :
+ y_ref_sign < 0 ? (-phone -bumper)[1] +y +l/2 :
+ y;
+ echo(eff_y);
+ translate([0, eff_y, 0])
children();
}
+module LidButtonishLeg(y, y_ref_sign, l=buttonishleg_default_l_is_fudge) {
+ $button_leg_only = true;
+ SideButton(y, y_ref_sign, l) children();
+}
+
module Buttons(){
- CaseBase_rhsflip([1]) SideButton(20.6, 8.8) children(); // power
+ CaseBase_rhsflip([1]) SideButton(15.580, +1, 8.9) children(); // power
+ CaseBase_rhsflip([1]) SideButton(48.700, -1, 8.920) children(); // camera
+ CaseBase_rhsflip([0]) SideButton(30.800, +1, 21.96) children(); // volume
+ CaseBase_rhsflip( ) LidButtonishLeg(20, -1) children();
+// CaseBase_rhsflip([0]) LidButtonishLeg(20, +1, 20) children();
}
module Struts(x_start, z_min, th){
mirror([0, 0, 1])
linear_extrude(height = 20)
mirror([0, 1, 0])
+ translate(bumper)
rectfromto(camera_pos_tl, camera_pos_br);
// struts (invisible, because they're buried in the case)
Buttons(){
mirror([1,0,0])
rotate([90,0,90]) {
- translate([0,0,-10])
- linear_extrude(height= 20)
- ButtonPlan($button_l, 0,1);
+ intersection(){
+ translate([0,0,-10])
+ linear_extrude(height= 20)
+ ButtonPlan($button_l, 0,1);
+ if ($button_leg_only)
+ rotate([-90,90,0])
+ translate([phone_width/2, -400, kppe[1]])
+ mirror([$rhsflip,0,0]) cube([400, 800, 50]);
+ }
translate([0,0, -bppR[0]])
linear_extrude(height= 20)
ButtonPlan($button_l, 1,1);
}
}
+
+ // apertures along top edge
+ CaseAperture(jack_pos, jack_dia, 8);
+ CaseBase_rhsflip([1])
+ CaseAperture(noisecancelmic_pos, noisecancelmic_dia, 20);
+
+ // rear speaker
+ CaseBase_rhsflip([1]) CaseBase_botflip([1])
+ linextr(-20, 20)
+ mirror([0,1])
+ translate(rearspeaker_pos_bl + bumper)
+ rectfromto(-rearspeaker_gap,
+ rearspeaker_size + rearspeaker_gap);
}
}
rotate([90,0,90])
translate([0,0,-10])
linear_extrude(height= 20)
- ButtonPlan($button_l, 0,0);
+ ButtonPlan($button_l, 1,0);
rotate([90,0,0])
translate([0,0,-100])
linear_extrude(height= 200)
}
}
+module TestSelectWidth(){
+ translate([-30, -(phone_height - 25), -20])
+ mirror([0, 1, 0])
+ cube([200, 50, 40]);
+}
+
module TestWidth(){ ////toplevel
intersection(){
Case();
- translate([-30, -(phone_height - 25), -20])
- mirror([0, 1, 0])
- cube([200, 50, 40]);
+ TestSelectWidth();
}
}
module TestLidWidthPrint(){ ////toplevel
- rotate([0,180.0])
- intersection(){
- Lid();
- translate([-30, -(phone_height - 25), -20])
- mirror([0, 1, 0])
- cube([200, 50, 40]);
- }
+ rotate([0,180.0]) intersection(){
+ Lid();
+ TestSelectWidth();
+ }
+}
+
+module TestSelectCamera(){
+ CaseBase_rhsflip(1)
+ translate([0,0,-25])
+ linear_extrude(height = 50)
+ mirror([0, 1, 0])
+ rectfromto([-20, -20],
+ camera_pos_br + bumper + [ 5, 5 ]);
}
module TestCamera(){ ////toplevel
intersection(){
Case();
- CaseBase_rhsflip(1)
- translate([0,0,-25])
- linear_extrude(height = 50)
- mirror([0, 1, 0])
- rectfromto([-20, -20],
- camera_pos_br + [ 5, 5 ]);
+ TestSelectCamera();
}
}
+module TestLidByCamera(){ ////toplevel
+ intersection(){
+ Lid();
+ TestSelectCamera();
+ }
+}
+
+module TestLidByCameraPrint(){ ////toplevel
+ rotate([180,0,0]) TestLidByCamera();
+}
+
+module DemoByCamera(){ ////toplevel
+ color("blue") TestLidByCamera();
+ color("red") TestCamera();
+}
+
module OneKeeper(){ ////toplevel
translate([0, -phone_cnr_rad, 0])
rotate([90, 0, 0])
OneKeeper();
}
+module LidPrint(){ ////toplevel
+ rotate([0,180,0])
+ Lid();
+}
+
+module TestSelectFrame(){
+ include = [1,-1] * (epp2i[0] + 4);
+
+ difference(){
+ cube(1000, center=true);
+ translate([0,0, -100])
+ linear_extrude(height=200)
+ rectfromto(include, inside_br - include);
+ }
+}
+
+module TestFrameCase(){ ////toplevel
+ intersection(){
+ Case();
+ union(){
+ TestSelectFrame();
+ TestSelectCamera();
+ }
+ }
+}
+
+module TestFrameLidPrint(){ ////toplevel
+ rotate([0,0,180]) intersection(){
+ Lid();
+ TestSelectFrame();
+ }
+}
+
module Keeper(){ ////toplevel
CaseBase_rhsflip()
OneKeeper();