setting('retraction_amount', 4.5, float, 'advanced', _('Retraction')).setRange(0).setLabel(_("Distance (mm)"), _("Amount of retraction, set at 0 for no retraction at all. A value between 1 and 2 millimeters provides good results for most materials."))
setting('retraction_dual_amount', 16.5, float, 'advanced', _('Retraction')).setRange(0).setLabel(_("Dual extrusion switch amount (mm)"), _("Amount of retraction when switching nozzle with dual-extrusion, set at 0 for no retraction at all. A value of 16.0mm seems to generate good results."))
setting('retraction_min_travel', 1.5, float, 'expert', _('Retraction')).setRange(0).setLabel(_("Minimum travel (mm)"), _("Minimum amount of travel needed for a retraction to happen at all. This setting is used to prevent from having too many retractions in a small area."))
-setting('retraction_combing', 'All', [_('Off'),_('All'),_('No Skin')], 'expert', _('Retraction')).setLabel(_("Enable combing"), _("Combing is the act of avoiding holes in the print for the head to travel over. If combing is \'Off\' the printer head moves straight from the start point to the end point and it will always retract. If \'All\', enable combing on all surfaces. If \'No Skin\', enable combing on all except skin surfaces."))
+setting('retraction_combing', 'All', [_('Off'),_('All'),_('No Skin')], 'expert', _('Retraction')).setLabel(_("Combing type"), _("When moving between print areas, combing keeps the print head above already printed areas and skips retraction. This helps reduce stringing and reduces the chance of grinding the filament. If combing is \'Off\' the printer head moves straight from the start point to the end point and it will always retract. If \'All\', combing is always enabled. If \'No Skin\', combing will not occur on skin (top/bottom fill layers) surfaces."))
setting('retraction_minimal_extrusion',0.02, float,'expert', _('Retraction')).setRange(0).setLabel(_("Minimal extrusion before retracting (mm)"), _("The minimal amount of extrusion that needs to be done before retracting again if a retraction needs to happen before this minimal is reached the retraction is ignored.\nThis avoids retracting a lot on the same piece of filament which flattens the filament and causes grinding issues."))
setting('retraction_hop', 0.0, float, 'expert', _('Retraction')).setRange(0).setLabel(_("Z hop when retracting (mm)"), _("When a retraction is done, the head is lifted by this amount to travel over the print. A value of 0.075 works well. This feature has a lot of positive effect on delta towers."))
setting('bottom_thickness', 0.3, float, 'advanced', _('Quality')).setRange(0).setLabel(_("Initial layer thickness (mm)"), _("Layer thickness of the bottom layer. A thicker bottom layer makes sticking to the bed easier. Set to 0.0 to have the bottom layer thickness the same as the other layers."))
setting('solid_bottom', True, bool, 'expert', _('Infill')).setLabel(_("Solid infill bottom"), _("Create a solid bottom surface, if set to false the bottom is filled with the fill percentage. Useful for buildings."))
setting('fill_overlap', 15, int, 'expert', _('Infill')).setRange(0,100).setLabel(_("Infill overlap (%)"), _("Amount of overlap between the infill and the walls. There is a slight overlap with the walls and the infill so the walls connect firmly to the infill."))
setting('support_type', 'Lines', ['Grid', 'Lines'], 'expert', _('Support')).setLabel(_("Structure type"), _("The type of support structure.\nGrid is very strong and can come off in 1 piece, however, sometimes it is too strong.\nLines are single walled lines that break off one at a time. Which is more work to remove, but as it is less strong it does work better on tricky prints."))
-setting('support_angle', 60, float, 'expert', _('Support')).setRange(0,90).setLabel(_("Overhang angle for support (deg)"), _("The minimal angle that overhangs need to have to get support. With 90 degree being horizontal and 0 degree being vertical."))
+setting('support_angle', 60, float, 'expert', _('Support')).setRange(0,90).setLabel(_("Overhang angle for support (deg)"), _("The minimal angle that overhangs need to have to get support. Setting this to 0 degrees means every overhang will be supported. 90 degrees effectively disables support."))
setting('support_fill_rate', 15, int, 'expert', _('Support')).setRange(0,100).setLabel(_("Fill amount (%)"), _("Amount of infill structure in the support material, less material gives weaker support which is easier to remove. 15% seems to be a good average."))
setting('support_xy_distance', 0.7, float, 'expert', _('Support')).setRange(0,10).setLabel(_("Distance X/Y (mm)"), _("Distance of the support material from the print, in the X/Y directions.\n0.7mm gives a nice distance from the print so the support does not stick to the print."))
setting('support_z_distance', 0.15, float, 'expert', _('Support')).setRange(0,10).setLabel(_("Distance Z (mm)"), _("Distance from the top/bottom of the support to the print. A small gap here makes it easier to remove the support but makes the print a bit uglier.\n0.15mm gives a good seperation of the support material."))
""", str, 'alteration', 'alteration')
setting('startMode', 'Simple', ['Simple', 'Normal'], 'preference', 'hidden')
-setting('simpleModeProfile', '2_normal', str, 'hidden', 'hidden')
-setting('simpleModeMaterial', '1_pla', str, 'hidden', 'hidden')
+setting('simpleModeProfile', 'Standard', str, 'hidden', 'hidden')
+setting('simpleModeMaterial', 'PLA', str, 'hidden', 'hidden')
+setting('simpleModeMaterialType', 'Beginner', str, 'hidden', 'hidden')
setting('oneAtATime', 'False', bool, 'preference', 'hidden')
setting('lastFile', os.path.normpath(os.path.join(os.path.dirname(os.path.abspath(__file__)), '..', 'resources', 'example', 'Rocktopus.stl')), str, 'preference', 'hidden')
setting('save_profile', 'False', bool, 'preference', 'hidden').setLabel(_("Save profile on slice"), _("When slicing save the profile as [stl_file]_profile.ini next to the model."))
setting('model_colour2', '#CB3030', str, 'preference', 'hidden').setLabel(_('Model colour (2)'), _('Display color for second extruder'))
setting('model_colour3', '#DDD93C', str, 'preference', 'hidden').setLabel(_('Model colour (3)'), _('Display color for third extruder'))
setting('model_colour4', '#4550D3', str, 'preference', 'hidden').setLabel(_('Model colour (4)'), _('Display color for forth extruder'))
-setting('printing_window', 'Pronterface UI', ['Basic'], 'preference', 'hidden').setLabel(_('Printing window type'), _('Select the interface used for USB printing.'))
setting('window_maximized', 'True', bool, 'preference', 'hidden')
setting('window_pos_x', '-1', float, 'preference', 'hidden')
setting('serial_baud', 'AUTO', str, 'machine', 'hidden').setLabel(_("Baudrate"), _("Speed of the serial port communication\nNeeds to match your firmware settings\nCommon values are 250000, 115200, 57600"))
setting('serial_baud_auto', '', int, 'machine', 'hidden')
+setting('toolhead', 'Default', str, 'machine', 'hidden').setLabel(_("Installed Tool Head"), _("Which tool head is currently installed. This setting is only used by LulzBot machines."))
+setting('toolhead_shortname', '', str, 'machine', 'hidden')
setting('extruder_head_size_min_x', '0.0', float, 'machine', 'hidden').setLabel(_("Head size towards X min (mm)"), _("The head size when printing multiple objects, measured from the tip of the nozzle towards the outer part of the head."))
setting('extruder_head_size_min_y', '0.0', float, 'machine', 'hidden').setLabel(_("Head size towards Y min (mm)"), _("The head size when printing multiple objects, measured from the tip of the nozzle towards the outer part of the head."))
setting('extruder_head_size_max_x', '0.0', float, 'machine', 'hidden').setLabel(_("Head size towards X max (mm)"), _("The head size when printing multiple objects, measured from the tip of the nozzle towards the outer part of the head."))
section = 'profile'
if set.isAlteration():
section = 'alterations'
- if profileParser.has_option(section, set.getName()):
- set.setValue(unicode(profileParser.get(section, set.getName()), 'utf-8', 'replace'))
- #Upgrade setting from older ini file
- if getProfileSetting('retraction_combing') == '1':
- putProfileSetting('retraction_combing', 'All')
+ setting_name = set.getName()
+ if profileParser.has_option(section, setting_name):
+ try:
+ setting = profileParser.get(section, setting_name)
+ if setting == "Invalid Value":
+ raise Exception
+ set.setValue(unicode(setting, 'utf-8', 'replace'))
+ pass
+ except:
+ set.setValue(set.getDefault())
def saveProfile(filename, allMachines = False):
"""
return 1
return n
+def getMachineName(index = None):
+ name = getMachineSetting('machine_name', index)
+ type = getMachineSetting('machine_type', index)
+ if type.startswith('lulzbot_'):
+ toolhead = getMachineSetting('toolhead_shortname', index)
+ if toolhead != '':
+ return "%s (%s)" % (name, toolhead)
+ return name
+
def setActiveMachine(index):
global _selectedMachineIndex
_selectedMachineIndex = index
def getMachineCenterCoords():
if getMachineSetting('machine_center_is_zero') == 'True':
return [0, 0]
- elif getMachineSetting('machine_type') == 'lulzbot_mini':
- return [(getMachineSettingFloat('machine_width') / 2) + 2.5, (getMachineSettingFloat('machine_width') / 2) + 0.5]
+ elif getMachineSetting('machine_type') == 'lulzbot_mini' or \
+ getMachineSetting('machine_type') == 'lulzbot_TAZ_6':
+ return [(getMachineSettingFloat('machine_width') / 2) + 2.5,
+ (getMachineSettingFloat('machine_width') / 2) + 0.5]
return [getMachineSettingFloat('machine_width') / 2, getMachineSettingFloat('machine_depth') / 2]
#Returns a list of convex polygons, first polygon is the allowed area of the machine,
#Append the profile string to the end of the GCode, so we can load it from the GCode file later.
#postfix = ';CURA_PROFILE_STRING:%s\n' % (getProfileString())
return unicode(prefix + re.sub("(.)\{([^\}]*)\}", replaceTagMatch, alterationContents).rstrip() + '\n' + postfix).strip().encode('utf-8') + '\n'
+
+def hasEmptyHeadSizeSettings(n):
+ return getMachineSetting('extruder_head_size_min_x', n) == '0.0' and \
+ getMachineSetting('extruder_head_size_max_x', n) == '0.0' and \
+ getMachineSetting('extruder_head_size_min_y', n) == '0.0' and \
+ getMachineSetting('extruder_head_size_max_y', n) == '0.0' and \
+ getMachineSetting('extruder_head_size_height', n) == '0.0'
+
+def performVersionUpgrade():
+ for n in xrange(0, getMachineCount()):
+ # This is a hack around an issue where the machine type in the wizard
+ # changed and causes some people to have it set to lulzbot_TAZ and some
+ # people have it set to lulzbot_TAZ_4.
+ if getMachineSetting('machine_type', n) == 'lulzbot_TAZ':
+ putMachineSetting('machine_type', 'lulzbot_TAZ_4', n)
+
+ machine_type = getMachineSetting('machine_type', n)
+ isLulzBot = machine_type.startswith('lulzbot_')
+ if isLulzBot and getMachineSetting('toolhead', n) == 'Default':
+ if machine_type == 'lulzbot_mini':
+ putMachineSetting('toolhead', 'Single Extruder V2', n)
+ putMachineSetting('toolhead_shortname', '', n)
+ elif machine_type == 'lulzbot_TAZ_4':
+ putMachineSetting('toolhead', 'Single Extruder V1', n)
+ putMachineSetting('toolhead_shortname', '', n)
+ putMachineSetting('machine_type', 'lulzbot_TAZ_4_SingleV1', n)
+ elif machine_type == 'lulzbot_TAZ_5':
+ putMachineSetting('toolhead', 'Single Extruder V2 (0.35mm nozzle)', n)
+ putMachineSetting('toolhead_shortname', '0.35 nozzle', n)
+ putMachineSetting('machine_type', 'lulzbot_TAZ_5_035nozzle', n)
+ machine_name = getMachineSetting('machine_name', n)
+ if machine_name.endswith(" (0.35 nozzle)"):
+ putMachineSetting('machine_name', machine_name.replace(" (0.35 nozzle)", ""), n)
+ elif machine_type == 'lulzbot_TAZ_5_05nozzle':
+ putMachineSetting('toolhead', 'Single Extruder V2 (0.5mm nozzle)', n)
+ putMachineSetting('toolhead_shortname', '0.5 nozzle', n)
+ putMachineSetting('machine_type', 'lulzbot_TAZ_5_05nozzle', n)
+ machine_name = getMachineSetting('machine_name', n)
+ if machine_name.endswith(" (0.5 nozzle)"):
+ putMachineSetting('machine_name', machine_name.replace(" (0.5 nozzle)", ""), n)
+
+ # Change TAZ print bed so prints are centered when scaled to the max
+ if machine_type.startswith('lulzbot_TAZ_') and \
+ getMachineSetting('machine_width', n) == '298':
+ putMachineSetting('machine_width', '290', n)
+
+ #Set valid extruder head size numbers for Mini
+ if machine_type == 'lulzbot_mini' and hasEmptyHeadSizeSettings(n):
+ putMachineSetting('extruder_head_size_min_x', '40', n)
+ putMachineSetting('extruder_head_size_max_x', '75', n)
+ putMachineSetting('extruder_head_size_min_y', '25', n)
+ putMachineSetting('extruder_head_size_max_y', '55', n)
+ putMachineSetting('extruder_head_size_height', '17', n)
\ No newline at end of file
~ianmdlvl / cura.git / blobdiff