setting('support', 'None', [_('None'), _('Touching buildplate'), _('Everywhere')], 'basic', _('Support')).setLabel(_("Support type"), _("Type of support structure build.\n\"Touching buildplate\" is the most commonly used support setting.\n\nNone does not do any support.\nTouching buildplate only creates support where the support structure will touch the build platform.\nEverywhere creates support even on top of parts of the model."))
setting('platform_adhesion', 'None', [_('None'), _('Brim'), _('Raft')], 'basic', _('Support')).setLabel(_("Platform adhesion type"), _("Different options that help in preventing corners from lifting due to warping.\nBrim adds a single layer thick flat area around your object which is easy to cut off afterwards, and the recommended option.\nRaft adds a thick raster at below the object and a thin interface between this and your object.\n(Note that enabling the brim or raft disables the skirt)"))
setting('support_dual_extrusion', 'Both', [_('Both'), _('First extruder'), _('Second extruder')], 'basic', _('Support')).setLabel(_("Support dual extrusion"), _("Which extruder to use for support material, for break-away support you can use both extruders.\nBut if one of the materials is more expensive then the other you could select an extruder to use for support material. This causes more extruder switches.\nYou can also use the 2nd extruder for soluble support materials."))
+setting('wipe_tower', False, bool, 'basic', _('Dual extrusion')).setLabel(_("Wipe&prime tower"), _("The wipe-tower is a tower printed on every layer when switching between nozzles.\nThe old nozzle is wiped off on the tower before the new nozzle is used to print the 2nd color."))
+setting('ooze_shield', False, bool, 'basic', _('Dual extrusion')).setLabel(_("Ooze shield"), _("The ooze shield is a 1 line thick shell around the object which stands a few mm from the object.\nThis shield catches any oozing from the unused nozzle in dual-extrusion."))
setting('filament_diameter', 2.85, float, 'basic', _('Filament')).setRange(1).setLabel(_("Diameter (mm)"), _("Diameter of your filament, as accurately as possible.\nIf you cannot measure this value you will have to calibrate it, a higher number means less extrusion, a smaller number generates more extrusion."))
setting('filament_diameter2', 0, float, 'basic', _('Filament')).setRange(0).setLabel(_("Diameter2 (mm)"), _("Diameter of your filament for the 2nd nozzle. Use 0 to use the same diameter as for nozzle 1."))
setting('filament_diameter3', 0, float, 'basic', _('Filament')).setRange(0).setLabel(_("Diameter3 (mm)"), _("Diameter of your filament for the 3th nozzle. Use 0 to use the same diameter as for nozzle 1."))
setting('filament_diameter4', 0, float, 'basic', _('Filament')).setRange(0).setLabel(_("Diameter4 (mm)"), _("Diameter of your filament for the 4th nozzle. Use 0 to use the same diameter as for nozzle 1."))
-setting('filament_flow', 100., float, 'basic', _('Filament')).setRange(1,300).setLabel(_("Flow (%)"), _("Flow compensation, the amount of material extruded is multiplied by this value"))
+setting('filament_flow', 100., float, 'basic', _('Filament')).setRange(5,300).setLabel(_("Flow (%)"), _("Flow compensation, the amount of material extruded is multiplied by this value"))
setting('retraction_speed', 40.0, float, 'advanced', _('Retraction')).setRange(0.1).setLabel(_("Speed (mm/s)"), _("Speed at which the filament is retracted, a higher retraction speed works better. But a very high retraction speed can lead to filament grinding."))
setting('retraction_amount', 4.5, float, 'advanced', _('Retraction')).setRange(0).setLabel(_("Distance (mm)"), _("Amount of retraction, set at 0 for no retraction at all. A value of 4.5mm seems to generate good results."))
setting('retraction_dual_amount', 16.5, float, 'advanced', _('Retraction')).setRange(0).setLabel(_("Dual extrusion switch amount (mm)"), _("Amount of retraction when switching nozzle with dual-extrusion, set at 0 for no retraction at all. A value of 16.0mm seems to generate good results."))
setting('retraction_min_travel', 1.5, float, 'expert', _('Retraction')).setRange(0).setLabel(_("Minimum travel (mm)"), _("Minimum amount of travel needed for a retraction to happen at all. To make sure you do not get a lot of retractions in a small area."))
setting('retraction_combing', True, bool, 'expert', _('Retraction')).setLabel(_("Enable combing"), _("Combing is the act of avoiding holes in the print for the head to travel over. If combing is disabled the printer head moves straight from the start point to the end point and it will always retract."))
-setting('retraction_minimal_extrusion',0.5, float,'expert', _('Retraction')).setRange(0).setLabel(_("Minimal extrusion before retracting (mm)"), _("The minimal amount of extrusion that needs to be done before retracting again if a retraction needs to happen before this minimal is reached the retraction is ignored.\nThis avoids retraction a lot on the same piece of filament which flattens the filament and causes grinding issues."))
+setting('retraction_minimal_extrusion',0.1, float,'expert', _('Retraction')).setRange(0).setLabel(_("Minimal extrusion before retracting (mm)"), _("The minimal amount of extrusion that needs to be done before retracting again if a retraction needs to happen before this minimal is reached the retraction is ignored.\nThis avoids retraction a lot on the same piece of filament which flattens the filament and causes grinding issues."))
setting('bottom_thickness', 0.3, float, 'advanced', _('Quality')).setRange(0).setLabel(_("Initial layer thickness (mm)"), _("Layer thickness of the bottom layer. A thicker bottom layer makes sticking to the bed easier. Set to 0.0 to have the bottom layer thickness the same as the other layers."))
setting('object_sink', 0.0, float, 'advanced', _('Quality')).setLabel(_("Cut off object bottom (mm)"), _("Sinks the object into the platform, this can be used for objects that do not have a flat bottom and thus create a too small first layer."))
#setting('enable_skin', False, bool, 'advanced', _('Quality')).setLabel(_("Duplicate outlines"), _("Skin prints the outer lines of the prints twice, each time with half the thickness. This gives the illusion of a higher print quality."))
-setting('overlap_dual', 0.2, float, 'advanced', _('Quality')).setLabel(_("Dual extrusion overlap (mm)"), _("Add a certain amount of overlapping extrusion on dual-extrusion prints. This bonds the different colors better together."))
+setting('overlap_dual', 0.15, float, 'advanced', _('Quality')).setLabel(_("Dual extrusion overlap (mm)"), _("Add a certain amount of overlapping extrusion on dual-extrusion prints. This bonds the different colors better together."))
setting('travel_speed', 150.0, float, 'advanced', _('Speed')).setRange(0.1).setLabel(_("Travel speed (mm/s)"), _("Speed at which travel moves are done, a high quality build Ultimaker can reach speeds of 250mm/s. But some machines might miss steps then."))
setting('bottom_layer_speed', 20, float, 'advanced', _('Speed')).setRange(0.1).setLabel(_("Bottom layer speed (mm/s)"), _("Print speed for the bottom layer, you want to print the first layer slower so it sticks better to the printer bed."))
setting('infill_speed', 0.0, float, 'advanced', _('Speed')).setRange(0.0).setLabel(_("Infill speed (mm/s)"), _("Speed at which infill parts are printed. If set to 0 then the print speed is used for the infill. Printing the infill faster can greatly reduce printing, but this can negatively effect print quality.."))
setting('support_fill_rate', 15, int, 'expert', _('Support')).setRange(0,100).setLabel(_("Fill amount (%)"), _("Amount of infill structure in the support material, less material gives weaker support which is easier to remove. 15% seems to be a good average."))
setting('support_xy_distance', 0.7, float, 'expert', _('Support')).setRange(0,10).setLabel(_("Distance X/Y (mm)"), _("Distance of the support material from the print, in the X/Y directions.\n0.7mm gives a nice distance from the print so the support does not stick to the print."))
setting('support_z_distance', 0.15, float, 'expert', _('Support')).setRange(0,10).setLabel(_("Distance Z (mm)"), _("Distance from the top/bottom of the support to the print. A small gap here makes it easier to remove the support but makes the print a bit uglier.\n0.15mm gives a good seperation of the support material."))
-#setting('joris', False, bool, 'expert', 'Joris').setLabel(_("Spiralize the outer contour"), _("[Joris] is a code name for smoothing out the Z move of the outer edge. This will create a steady Z increase over the whole print. It is intended to be used with a single walled wall thickness to make cups/vases."))
+setting('spiralize', False, bool, 'expert', 'Spiralize').setLabel(_("Spiralize the outer contour"), _("Spiralize is smoothing out the Z move of the outer edge. This will create a steady Z increase over the whole print. This feature turns a solid object into a single walled print with a solid bottom."))
#setting('bridge_speed', 100, int, 'expert', 'Bridge').setRange(0,100).setLabel(_("Bridge speed (%)"), _("Speed at which layers with bridges are printed, compared to normal printing speed."))
setting('brim_line_count', 20, int, 'expert', _('Brim')).setRange(1,100).setLabel(_("Brim line amount"), _("The amount of lines used for a brim, more lines means a larger brim which sticks better, but this also makes your effective print area smaller."))
setting('raft_margin', 5, float, 'expert', _('Raft')).setRange(0).setLabel(_("Extra margin (mm)"), _("If the raft is enabled, this is the extra raft area around the object which is also rafted. Increasing this margin will create a stronger raft while using more material and leaving less are for your print."))
setting('has_heated_bed', 'False', bool, 'machine', 'hidden').setLabel(_("Heated bed"), _("If you have an heated bed, this enabled heated bed settings (requires restart)"))
setting('gcode_flavor', 'RepRap (Marlin/Sprinter)', ['RepRap (Marlin/Sprinter)', 'UltiGCode', 'MakerBot'], 'machine', 'hidden').setLabel(_("GCode Flavor"), _("Flavor of generated GCode.\nRepRap is normal 5D GCode which works on Marlin/Sprinter based firmwares.\nUltiGCode is a variation of the RepRap GCode which puts more settings in the machine instead of the slicer.\nMakerBot GCode has a few changes in the way GCode is generated, but still requires MakerWare to generate to X3G."))
setting('extruder_amount', '1', ['1','2','3','4'], 'machine', 'hidden').setLabel(_("Extruder count"), _("Amount of extruders in your machine."))
-setting('extruder_offset_x1', '-21.6', float, 'machine', 'hidden').setLabel(_("Offset X"), _("The offset of your secondary extruder compared to the primary."))
-setting('extruder_offset_y1', '0.0', float, 'machine', 'hidden').setLabel(_("Offset Y"), _("The offset of your secondary extruder compared to the primary."))
+setting('extruder_offset_x1', '0.0', float, 'machine', 'hidden').setLabel(_("Offset X"), _("The offset of your secondary extruder compared to the primary."))
+setting('extruder_offset_y1', '-21.6', float, 'machine', 'hidden').setLabel(_("Offset Y"), _("The offset of your secondary extruder compared to the primary."))
setting('extruder_offset_x2', '0.0', float, 'machine', 'hidden').setLabel(_("Offset X"), _("The offset of your tertiary extruder compared to the primary."))
setting('extruder_offset_y2', '0.0', float, 'machine', 'hidden').setLabel(_("Offset Y"), _("The offset of your tertiary extruder compared to the primary."))
setting('extruder_offset_x3', '0.0', float, 'machine', 'hidden').setLabel(_("Offset X"), _("The offset of your forth extruder compared to the primary."))
settingsDictionary['filament_diameter4'].addCondition(lambda : int(getMachineSetting('extruder_amount')) > 3)
settingsDictionary['support_dual_extrusion'].addCondition(lambda : int(getMachineSetting('extruder_amount')) > 1)
settingsDictionary['retraction_dual_amount'].addCondition(lambda : int(getMachineSetting('extruder_amount')) > 1)
+settingsDictionary['wipe_tower'].addCondition(lambda : int(getMachineSetting('extruder_amount')) > 1)
+settingsDictionary['ooze_shield'].addCondition(lambda : int(getMachineSetting('extruder_amount')) > 1)
#Heated bed
settingsDictionary['print_bed_temperature'].addCondition(lambda : getMachineSetting('has_heated_bed') == 'True')
wallThickness = getProfileSettingFloat('wall_thickness')
nozzleSize = getProfileSettingFloat('nozzle_size')
+ if getProfileSetting('spiralize') == 'True':
+ return wallThickness
+
if wallThickness < 0.01:
return nozzleSize
if wallThickness < nozzleSize:
return 0
if wallThickness < nozzleSize:
return 1
+ if getProfileSetting('spiralize') == 'True':
+ return 1
lineCount = int(wallThickness / (nozzleSize - 0.0001))
if lineCount < 1:
postfix = ''
alterationContents = getAlterationFile(filename)
if getMachineSetting('gcode_flavor') == 'UltiGCode':
+ if filename == 'end.gcode':
+ return 'M25 ;Stop reading from this point on.\n'
return ''
if filename == 'start.gcode':
if extruderCount > 1:
if getMachineSetting('has_heated_bed') == 'True':
bedTemp = getProfileSettingFloat('print_bed_temperature')
- if bedTemp > 0 and isTagIn('{print_bed_temperature}', alterationContents):
+ if bedTemp > 0 and not isTagIn('{print_bed_temperature}', alterationContents):
prefix += 'M140 S%f\n' % (bedTemp)
if temp > 0 and not isTagIn('{print_temperature}', alterationContents):
if extruderCount > 0:
~ianmdlvl / cura.git / blobdiff