.TH GPIO 1 "September 2015" wiringPi "Command-Line access to Raspberry Pi's GPIO" .SH NAME gpio \- Command-line access to Raspberry Pi's GPIO .SH SYNOPSIS .B gpio .B \-v .PP .B gpio .B [ \-g | \-1 ] .B mode/read/write/aread/awrite/wb/pwm/clock ... .PP .B gpio .B [ \-x extension:params ] .B mode/read/write/aread/awrite/pwm/pwmTone ... .PP .B gpio .B [ \-p ] .B read/write/toggle/wb .B ... .PP .B gpio .B readall .PP .B gpio .B unexportall/exports .PP .B gpio .B export/edge/unexport .B ... .PP .B gpio .B wfi .B ... .PP .B gpio .B drive group value .PP .B gpio .B usbp high | low .PP .B gpio .B pwm-bal/pwm-ms .PP .B gpio .B pwmr range .PP .B gpio .B load \ i2c/spi ... .PP .B gpio .B gbr channel .PP .B gpio .B gbw channel value .SH DESCRIPTION .B GPIO is a swiss army knife of a command line tool to allow the user easy access to the GPIO pins on the Raspberry Pi and the SPI A/D and D/A converters on the Gertboard. It's designed for simple testing and diagnostic purposes, but can be used in shell scripts for general if somewhat slow control of the GPIO pins. It can also control the IO's on the PiFace IO board and load the SPI and I2C kernel modules if required. Additionally, it can be used to set the exports in the \fI/sys/class/gpio\fR system directory to allow subsequent programs to use the \fR/sys/class/gpio\fR interface without needing to be run as root. .SH OPTIONS .TP .B \-v Output the current version including the board revision of the Raspberry Pi. .TP .B \-g Use the BCM_GPIO pins numbers rather than wiringPi pin numbers. \fINote:\fR The BCM_GPIO pin numbers are always used with the export and edge commands. .TP .B \-1 Use the physical pin numbers rather than wiringPi pin numbers. \fINote:\fR that this applies to the P1 connector only. It is not possible to use pins on the Revision 2 P5 connector this way, and as with \-g the BCM_GPIO pin numbers are always used with the export and edge commands. .TP .B \-x extension This causes the named extension to be initialised. Extensions comprise of a name (e.g. mcp23017) followed by a colon, then the pin-base, then more optional parameters depending on the extension type. See the web page on http://wiringpi.com/the-gpio-utility/ .TP .B \-p Use the PiFace interface board and its corresponding pin numbers. The PiFace will always appear at pin number 200 in the gpio command. You can assign any pin numbers you like in your own programs though. .TP .B read Read the digital value of the given pin and print 0 or 1 to represent the respective logic levels. .TP .B write Write the given value (0 or 1) to the pin. You need to set the pin to output mode first. .TP .B aread Read the analog value of the given pin. This needs to be uses in conjunction with a -x flag to add in an extension that handles analog inputs. respective logic levels. e.g. gpio -x mcp3002:200:0 aread 200 will read the first analog input on an mcp3002 SPI ADC chip. .TP .B awrite Write the analog value to the given pin. This needs to be used in conjunction with a -x flag to add in an extension that handles analog inputs. respective logic levels. e.g. gpio -x mcp4802:200:0 awrite 200 128 will write the value 128 to the first DAC port on an mcp4802 chip on the Pi's SPI bus 0. .TP .B wb Write the given byte to the 8 main GPIO pins. You can prefix it with 0x to specify a hexadecimal number. You need to set pins to output mode first. .TP .B readall Output a table of all GPIO pins values. The values represent the actual values read if the pin is in input mode, or the last value written if the pin is in output mode. The readall command is usable with an extension module (via the -x parameter), but it's unable to determine pin modes or states, so will perform both a digital and analog read on each pin in-turn. .TP .B pwm Write a PWM value (0-1023) to the given pin. The pin needs to be put into PWM mode first. .TP .B clock Set the output frequency on the given pin. The pin needs to be put into clock mode first. .TP .B mode Set a pin into \fIinput\fR, \fIoutput\fR or \fIpwm\fR mode. Can also use the literals \fIup\fR, \fIdown\fR or \fItri\fR to set the internal pull-up, pull-down or tristate (off) controls. The ALT modes can also be set using \fIalt0\fR, \fIalt1\fR, ... \fIalt5\fR. .TP .B unexportall Un-Export all the GPIO pins in the /sys/class/gpio directory. .TP .B exports Print a list (if any) of all the exported GPIO pins and their current values. .TP .B export Export a GPIO pin in the \fI/sys/class/gpio\fR directory. Use like the mode command above however only \fIin\fR, \fIout\fR, \fIhigh\fR and \fRlow\fR are supported at this time. Note that the pin number is the \fBBCM_GPIO\fR number and not the wiringPi number. The \fIhigh\fR and \fIlow\fR commands pre-set the output value at the same time as the export to output mode. Once a GPIO pin has been exported, the \fBgpio\fR program changes the ownership of the \fI/sys/class/gpio/gpioX/value\fR and if present in later kernels, the \fI/sys/class/gpio/gpioX/edge\fR pseudo files to that of the user running the \fBgpio\fR program. This means that you can have a small script of gpio exports to setup the gpio pins as your program requires without the need to run anything as root, or with the sudo command. .TP .B edge This exports a GPIO pin in the \fI/sys/class/gpio\fR directory, set the direction to input and set the edge interrupt method to \fInone\fR, \fIrising\fR, \fIfalling\fR or \fIboth\fR. Use like the export command above and note that \fBBCM_GPIO\fR pin number is used not not wiringPi pin numbering. Like the export commands above, ownership is set to that of the calling user, allowing subsequent access from user programs without requiring root/sudo. .TP .B unexport Un-Export a GPIO pin in the /sys/class/gpio directory. .TP .B wfi This set the given pin to the supplied interrupt mode: rising, falling or both then waits for the interrupt to happen. It's a non-busy wait, so does not consume and CPU while it's waiting. .TP .B drive group value Change the pad driver value for the given pad group to the supplied drive value. Group is 0, 1 or 2 and value is 0-7. Do not use unless you are absolutely sure you know what you're doing. .TP .B usbp high | low Change the USB current limiter to high (1.2 amps) or low (the default, 600mA) This is only applicable to the model B+ .TP .B pwm-bal/pwm-ms Change the PWM mode to balanced (the default) or mark:space ratio (traditional) .TP .B pwmr Change the PWM range register. The default is 1024. .TP .B load i2c [baudrate] This loads the i2c or drivers into the kernel and changes the permissions on the associated /dev/ entries so that the current user has access to them. Optionally it will set the I2C baudrate to that supplied in Kb/sec (or as close as the Pi can manage) The default speed is 100Kb/sec. Note: On recent kernels with the device tree enabled you should use the raspi-config program to load/unload the I2C device at boot time. (or disable the device tree to continue to use this method) .TP .B load spi This loads the spi drivers into the kernel and changes the permissions on the associated /dev/ entries so that the current user has access to them. It used to have the ability to change the buffer size from the default of 4096 bytes to an arbitary value, however for some time the Pi Foundation have compiled the SPI device driver into the kernel and this has fixed the buffer size. The way to change it now is to edit the /boot/cmdline.txt file and add on spdev.bufsiz=8192 to set it to e.g. 8192 bytes then reboot. Note: On recent kernels with the device tree enabled you should use the raspi-config program to load/unload the SPI device at boot time. (or disable the device tree to continue to use this method) .TP .B gbr channel This reads the analog to digital converter on the Gertboard on the given channel. The board jumpers need to be in-place to do this operation. .TP .B gbw channel value This writes the supplied value to the output channel on the Gertboards SPI digital to analogue converter. The board jumpers need to be in-place to do this operation. .SH "WiringPi vs. BCM_GPIO Pin numbering vs. Physical pin numbering" .PP The quickest way to get a list of the pin differences is to run the command .TP gpio readall .SH FILES .TP 2.2i .I gpio executable .SH EXAMPLES .TP 2.2i gpio mode 4 output # Set pin 4 to output .PP gpio -g mode 23 output # Set GPIO pin 23 to output (same as WiringPi pin 4) .PP gpio mode 1 pwm # Set pin 1 to PWM mode .PP gpio pwm 1 512 # Set pin 1 to PWM value 512 - half brightness .PP gpio export 17 out # Set GPIO Pin 17 to output .PP gpio export 0 in # Set GPIO Pin 0 (SDA0) to input. .PP gpio -g read 0 # Read GPIO Pin 0 (SDA0) .SH "NOTES" When using the \fIexport\fR, \fIedge\fR or \fIunexport\fR commands, the pin numbers are \fBalways\fR native BCM_GPIO numbers and never wiringPi pin numbers. .SH "SEE ALSO" .LP WiringPi's home page .IP http://wiringpi.com/ .SH AUTHOR Gordon Henderson .SH "REPORTING BUGS" Please report bugs to .SH COPYRIGHT Copyright (c) 2012-2015 Gordon Henderson This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. .SH TRADEMARKS AND ACKNOWLEDGEMENTS Raspberry Pi is a trademark of the Raspberry Pi Foundation. See http://raspberrypi.org/ for full details.