4 retraction_enable = True
5 solid_layer_thickness = 0.8
7 perimeter_before_infill = True
10 print_temperature = 250
11 print_temperature2 = 0
12 print_temperature3 = 0
13 print_temperature4 = 0
14 print_temperature5 = 0
15 print_bed_temperature = 110
17 platform_adhesion = None
18 support_dual_extrusion = Both
20 wipe_tower_volume = 15
22 filament_diameter = 2.85
23 filament_diameter2 = 0
24 filament_diameter3 = 0
25 filament_diameter4 = 0
26 filament_diameter5 = 0
30 retraction_dual_amount = 16.5
31 retraction_min_travel = 1.5
32 retraction_combing = All
33 retraction_minimal_extrusion = 0.005
35 bottom_thickness = 0.425
36 layer0_width_factor = 125
40 bottom_layer_speed = 15
45 cool_min_layer_time = 15
49 skirt_minimal_length = 250
53 cool_min_feedrate = 10
54 cool_head_lift = False
60 support_fill_rate = 30
61 support_xy_distance = 0.7
62 support_z_distance = 0.05
67 raft_line_spacing = 3.0
68 raft_base_thickness = 0.3
69 raft_base_linewidth = 1.0
70 raft_interface_thickness = 0.27
71 raft_interface_linewidth = 0.4
74 raft_surface_layers = 2
75 raft_surface_thickness = 0.27
76 raft_surface_linewidth = 0.4
77 fix_horrible_union_all_type_a = True
78 fix_horrible_union_all_type_b = False
79 fix_horrible_use_open_bits = False
80 fix_horrible_extensive_stitching = False
86 simplemodeprofile = 2_normal
87 simplemodematerial = 1_pla
88 simplemodematerialtype = Beginner
94 G90 ; absolute positioning
95 M82 ; set extruder to absolute mode
96 M107 ; start with the fan off
97 G92 E0 ; set extruder position to 0
98 M140 S{print_bed_temperature}; get bed heating up
100 M109 S150 ; set to cleaning temp and wait
101 G1 E-30 F100 ; suck up XXmm of filament
102 M109 S170 ; heat to probe temp
103 G1 X-15 Y100 F3000 ; move above wiper pad
104 G1 Z2 ; Push nozzle into wiper
105 G1 X-17 Y95 F1000 ; slow wipe
106 G1 X-17 Y90 F1000 ; slow wipe
107 G1 X-17 Y85 F1000 ; slow wipe
108 G1 X-15 Y90 F1000 ; slow wipe
109 G1 X-17 Y80 F1000 ; slow wipe
110 G1 X-15 Y95 F1000 ; slow wipe
111 G1 X-17 Y75 F2000 ; fast wipe
112 G1 X-15 Y65 F2000 ; fast wipe
113 G1 X-17 Y70 F2000 ; fast wipe
114 G1 X-15 Y60 F2000 ; fast wipe
115 G1 X-17 Y55 F2000 ; fast wipe
116 G1 X-15 Y50 F2000 ; fast wipe
117 G1 X-17 Y40 F2000 ; fast wipe
118 G1 X-15 Y45 F2000 ; fast wipe
119 G1 X-17 Y35 F2000 ; fast wipe
120 G1 X-15 Y40 F2000 ; fast wipe
121 G1 X-17 Y70 F2000 ; fast wipe
122 G1 X-15 Y30 Z2 F2000 ; fast wipe
123 G1 X-17 Y35 F2000 ; fast wipe
124 G1 X-15 Y25 F2000 ; fast wipe
125 G1 X-17 Y30 F2000 ; fast wipe
126 G1 X-15 Y25 Z1.5 F1000 ; slow wipe
127 G1 X-17 Y23 F1000 ; slow wipe
128 G1 Z10 ; raise extruder
129 G1 Y10 ; move above probe
130 M109 S170 ; set to probing temp
131 M204 S100 ; set accel for probing
133 M204 S700 ; set accel back to normal
134 G1 X0 Y0 Z15 F5000 ; get out the way
137 M109 S{print_temperature} ; set extruder temp and wait
138 G4 S25 ; wait for bed to temp up
139 G1 Z2 E0 F75 ; extrude filament back into nozzle
140 M140 S{print_bed_temperature}; get bed temping up during first layer
141 M117 Taz Printing... ; Message
144 M140 S0 ; heated bed heater off (if you have it)
146 G91 ; relative positioning
147 G1 E-1 F300 ; retract the filament a bit before lifting the nozzle, to release some of the pressure
148 G1 Z+0.5 E-5 X-20 Y-20 F3000 ; move Z up a bit and retract filament even more
149 G90 ; absolute positioning
150 G1 X0 Y250 ; move to cooling position
152 G90 ; absolute positioning
153 M117 TAZ 6 Ready. ;{profile_string}
154 start2.gcode = ;Sliced at: {day} {date} {time}
155 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
156 ;Print time: {print_time}
157 ;Filament used: {filament_amount}m {filament_weight}g
158 ;Filament cost: {filament_cost}
159 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
160 ;M104 S{print_temperature} ;Uncomment to add your own temperature line
161 ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
162 ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
164 G90 ;absolute positioning
165 M107 ;start with the fan off
166 G28 X0 Y0 ;move X/Y to min endstops
167 G28 Z0 ;move Z to min endstops
168 G1 Z15.0 F{travel_speed} ;move the platform down 15mm
169 T1 ;Switch to the 2nd extruder
170 G92 E0 ;zero the extruded length
171 G1 F200 E10 ;extrude 10mm of feed stock
172 G92 E0 ;zero the extruded length again
173 G1 F200 E-{retraction_dual_amount}
174 T0 ;Switch to the first extruder
175 G92 E0 ;zero the extruded length
176 G1 F200 E10 ;extrude 10mm of feed stock
177 G92 E0 ;zero the extruded length again
179 ;Put printing message on LCD screen
181 end2.gcode = ;End GCode
182 M104 T0 S0 ;extruder heater off
183 M104 T1 S0 ;extruder heater off
184 M140 S0 ;heated bed heater off (if you have it)
185 G91 ;relative positioning
186 G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
187 G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
188 G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
190 G90 ;absolute positioning
192 start3.gcode = ;Sliced at: {day} {date} {time}
193 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
194 ;Print time: {print_time}
195 ;Filament used: {filament_amount}m {filament_weight}g
196 ;Filament cost: {filament_cost}
197 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
198 ;M104 S{print_temperature} ;Uncomment to add your own temperature line
199 ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
200 ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
202 G90 ;absolute positioning
203 M107 ;start with the fan off
204 G28 X0 Y0 ;move X/Y to min endstops
205 G28 Z0 ;move Z to min endstops
206 G1 Z15.0 F{travel_speed} ;move the platform down 15mm
207 T2 ;Switch to the 2nd extruder
208 G92 E0 ;zero the extruded length
209 G1 F200 E10 ;extrude 10mm of feed stock
210 G92 E0 ;zero the extruded length again
211 G1 F200 E-{retraction_dual_amount}
212 T1 ;Switch to the 2nd extruder
213 G92 E0 ;zero the extruded length
214 G1 F200 E10 ;extrude 10mm of feed stock
215 G92 E0 ;zero the extruded length again
216 G1 F200 E-{retraction_dual_amount}
217 T0 ;Switch to the first extruder
218 G92 E0 ;zero the extruded length
219 G1 F200 E10 ;extrude 10mm of feed stock
220 G92 E0 ;zero the extruded length again
222 ;Put printing message on LCD screen
224 end3.gcode = ;End GCode
225 M104 T0 S0 ;extruder heater off
226 M104 T1 S0 ;extruder heater off
227 M104 T2 S0 ;extruder heater off
228 M140 S0 ;heated bed heater off (if you have it)
229 G91 ;relative positioning
230 G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
231 G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
232 G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
234 G90 ;absolute positioning
236 start4.gcode = ;Sliced at: {day} {date} {time}
237 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
238 ;Print time: {print_time}
239 ;Filament used: {filament_amount}m {filament_weight}g
240 ;Filament cost: {filament_cost}
241 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
242 ;M104 S{print_temperature} ;Uncomment to add your own temperature line
243 ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
244 ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
245 ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
247 G90 ;absolute positioning
248 M107 ;start with the fan off
249 G28 X0 Y0 ;move X/Y to min endstops
250 G28 Z0 ;move Z to min endstops
251 G1 Z15.0 F{travel_speed} ;move the platform down 15mm
252 T3 ;Switch to the 4th extruder
253 G92 E0 ;zero the extruded length
254 G1 F200 E10 ;extrude 10mm of feed stock
255 G92 E0 ;zero the extruded length again
256 G1 F200 E-{retraction_dual_amount}
257 T2 ;Switch to the 3th extruder
258 G92 E0 ;zero the extruded length
259 G1 F200 E10 ;extrude 10mm of feed stock
260 G92 E0 ;zero the extruded length again
261 G1 F200 E-{retraction_dual_amount}
262 T1 ;Switch to the 2nd extruder
263 G92 E0 ;zero the extruded length
264 G1 F200 E10 ;extrude 10mm of feed stock
265 G92 E0 ;zero the extruded length again
266 G1 F200 E-{retraction_dual_amount}
267 T0 ;Switch to the first extruder
268 G92 E0 ;zero the extruded length
269 G1 F200 E10 ;extrude 10mm of feed stock
270 G92 E0 ;zero the extruded length again
272 ;Put printing message on LCD screen
274 end4.gcode = ;End GCode
275 M104 T0 S0 ;extruder heater off
276 M104 T1 S0 ;extruder heater off
277 M104 T2 S0 ;extruder heater off
278 M104 T3 S0 ;extruder heater off
279 M140 S0 ;heated bed heater off (if you have it)
280 G91 ;relative positioning
281 G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
282 G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
283 G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
285 G90 ;absolute positioning
287 support_start.gcode =
292 preswitchextruder.gcode = ;Switch between the current extruder and the next ex
293 postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
294 ;This code is added after the T(n)