resources/quickprint/lulzbot_profiles/TAZ6_single_tilapia/HIPS_medium-speed_mangrove_single-extruder_0.5noz_cura.ini

   1 [profile]
   2 layer_height = 0.25
   3 wall_thickness = 1.0
   4 retraction_enable = True
   5 solid_layer_thickness = 0.8
   6 fill_density = 20
   7 perimeter_before_infill = True
   8 nozzle_size = 0.5
   9 print_speed = 50
  10 print_temperature = 250
  11 print_temperature2 = 0
  12 print_temperature3 = 0
  13 print_temperature4 = 0
  14 print_temperature5 = 0
  15 print_bed_temperature = 110
  16 support = None
  17 platform_adhesion = None
  18 support_dual_extrusion = Both
  19 wipe_tower = False
  20 wipe_tower_volume = 15
  21 ooze_shield = False
  22 filament_diameter = 2.85
  23 filament_diameter2 = 0
  24 filament_diameter3 = 0
  25 filament_diameter4 = 0
  26 filament_diameter5 = 0
  27 filament_flow = 100.0
  28 retraction_speed = 10
  29 retraction_amount = 1
  30 retraction_dual_amount = 16.5
  31 retraction_min_travel = 1.5
  32 retraction_combing = All
  33 retraction_minimal_extrusion = 0.005
  34 retraction_hop = 0.1
  35 bottom_thickness = 0.425
  36 layer0_width_factor = 125
  37 object_sink = 0.0
  38 overlap_dual = 0.15
  39 travel_speed = 175
  40 bottom_layer_speed = 15
  41 infill_speed = 50
  42 solidarea_speed = 45
  43 inset0_speed = 30
  44 insetx_speed = 35
  45 cool_min_layer_time = 20
  46 fan_enabled = True
  47 skirt_line_count = 1
  48 skirt_gap = 3.0
  49 skirt_minimal_length = 250
  50 fan_full_height = 0.5
  51 fan_speed = 40
  52 fan_speed_max = 50
  53 cool_min_feedrate = 10
  54 cool_head_lift = False
  55 solid_top = True
  56 solid_bottom = True
  57 fill_overlap = 15
  58 support_type = Lines
  59 support_angle = 45
  60 support_fill_rate = 30
  61 support_xy_distance = 0.7
  62 support_z_distance = 0.05
  63 spiralize = False
  64 simple_mode = False
  65 brim_line_count = 10
  66 raft_margin = 5.0
  67 raft_line_spacing = 3.0
  68 raft_base_thickness = 0.3
  69 raft_base_linewidth = 1.0
  70 raft_interface_thickness = 0.27
  71 raft_interface_linewidth = 0.4
  72 raft_airgap_all = 0.0
  73 raft_airgap = 0.5
  74 raft_surface_layers = 2
  75 raft_surface_thickness = 0.27
  76 raft_surface_linewidth = 0.4
  77 fix_horrible_union_all_type_a = True
  78 fix_horrible_union_all_type_b = False
  79 fix_horrible_use_open_bits = False
  80 fix_horrible_extensive_stitching = False
  81 plugin_config = (lp1
  82         .
  83 object_center_x = -1
  84 object_center_y = -1
  85 simplemodesettings =
  86 simplemodeprofile = 2_normal
  87 simplemodematerial = 1_pla
  88 simplemodematerialtype = Beginner
  89
  90 [alterations]
  91 start.gcode = G21
  92         M107                         ; disable fans
  93         G21                          ; metric values
  94         G90                          ; absolute positioning
  95         M82                          ; set extruder to absolute mode
  96         M107                         ; start with the fan off
  97         G92 E0                       ; set extruder position to 0
  98         M140 S{print_bed_temperature}; get bed heating up
  99         G28                          ; home all
 100         M109 S150                    ; set to cleaning temp and wait
 101         G1 E-30 F100                 ; suck up XXmm of filament
 102         M109 S170                    ; heat to probe temp
 103         G1 X-15 Y100 F3000           ; move above wiper pad
 104         G1 Z2                        ; Push nozzle into wiper
 105         G1 X-17 Y95 F1000            ; slow wipe
 106         G1 X-17 Y90 F1000            ; slow wipe
 107         G1 X-17 Y85 F1000            ; slow wipe
 108         G1 X-15 Y90 F1000            ; slow wipe
 109         G1 X-17 Y80 F1000            ; slow wipe
 110         G1 X-15 Y95 F1000            ; slow wipe
 111         G1 X-17 Y75 F2000            ; fast wipe
 112         G1 X-15 Y65 F2000            ; fast wipe
 113         G1 X-17 Y70 F2000            ; fast wipe
 114         G1 X-15 Y60 F2000            ; fast wipe
 115         G1 X-17 Y55 F2000            ; fast wipe
 116         G1 X-15 Y50 F2000            ; fast wipe
 117         G1 X-17 Y40 F2000            ; fast wipe
 118         G1 X-15 Y45 F2000            ; fast wipe
 119         G1 X-17 Y35 F2000            ; fast wipe
 120         G1 X-15 Y40 F2000            ; fast wipe
 121         G1 X-17 Y70 F2000            ; fast wipe
 122         G1 X-15 Y30 Z2 F2000         ; fast wipe
 123         G1 X-17 Y35 F2000            ; fast wipe
 124         G1 X-15 Y25 F2000            ; fast wipe
 125         G1 X-17 Y30 F2000            ; fast wipe
 126         G1 X-15 Y25 Z1.5 F1000       ; slow wipe
 127         G1 X-17 Y23 F1000            ; slow wipe
 128         G1 Z10                       ; raise extruder
 129         G1 Y10                       ; move above probe
 130         M109 S170                    ; set to probing temp
 131         M204 S100                    ; set accel for probing
 132         G29                          ; Probe
 133         M204 S700                    ; set accel back to normal
 134         G1 X0 Y0 Z15 F5000           ; get out the way
 135         M400                         ; clear buffer
 136         G4 S1                        ; pause
 137         M109 S{print_temperature}    ; set extruder temp and wait
 138         G4 S25                       ; wait for bed to temp up
 139         G1 Z2 E0 F75                 ; extrude filament back into nozzle
 140         M140 S{print_bed_temperature}; get bed temping up during first layer
 141         M117 Taz Printing...         ; Message
 142 end.gcode = M400
 143         M104 S0                        ; hotend off
 144         M140 S0                        ; heated bed heater off (if you have it)
 145         M107                           ; fans off
 146         G91                            ; relative positioning
 147         G1 E-1 F300                    ; retract the filament a bit before lifting the nozzle, to release some of the pressure
 148         G1 Z+0.5 E-5 X-20 Y-20 F3000   ; move Z up a bit and retract filament even more
 149         G90                            ; absolute positioning
 150         G1 X0 Y250                     ; move to cooling position
 151         M84                            ; steppers off
 152         G90                            ; absolute positioning
 153         M117 TAZ 6 Ready.              ;{profile_string}
 154 start2.gcode = ;Sliced at: {day} {date} {time}
 155         ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
 156         ;Print time: {print_time}
 157         ;Filament used: {filament_amount}m {filament_weight}g
 158         ;Filament cost: {filament_cost}
 159         ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
 160         ;M104 S{print_temperature} ;Uncomment to add your own temperature line
 161         ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
 162         ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
 163         G21        ;metric values
 164         G90        ;absolute positioning
 165         M107       ;start with the fan off
 166         G28 X0 Y0  ;move X/Y to min endstops
 167         G28 Z0     ;move Z to min endstops
 168         G1 Z15.0 F{travel_speed} ;move the platform down 15mm
 169         T1                      ;Switch to the 2nd extruder
 170         G92 E0                  ;zero the extruded length
 171         G1 F200 E10             ;extrude 10mm of feed stock
 172         G92 E0                  ;zero the extruded length again
 173         G1 F200 E-{retraction_dual_amount}
 174         T0                      ;Switch to the first extruder
 175         G92 E0                  ;zero the extruded length
 176         G1 F200 E10             ;extrude 10mm of feed stock
 177         G92 E0                  ;zero the extruded length again
 178         G1 F{travel_speed}
 179         ;Put printing message on LCD screen
 180         M117 Printing...
 181 end2.gcode = ;End GCode
 182         M104 T0 S0                     ;extruder heater off
 183         M104 T1 S0                     ;extruder heater off
 184         M140 S0                     ;heated bed heater off (if you have it)
 185         G91                                    ;relative positioning
 186         G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
 187         G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
 188         G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way
 189         M84                         ;steppers off
 190         G90                         ;absolute positioning
 191         ;{profile_string}
 192 start3.gcode = ;Sliced at: {day} {date} {time}
 193         ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
 194         ;Print time: {print_time}
 195         ;Filament used: {filament_amount}m {filament_weight}g
 196         ;Filament cost: {filament_cost}
 197         ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
 198         ;M104 S{print_temperature} ;Uncomment to add your own temperature line
 199         ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
 200         ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
 201         G21        ;metric values
 202         G90        ;absolute positioning
 203         M107       ;start with the fan off
 204         G28 X0 Y0  ;move X/Y to min endstops
 205         G28 Z0     ;move Z to min endstops
 206         G1 Z15.0 F{travel_speed} ;move the platform down 15mm
 207         T2                      ;Switch to the 2nd extruder
 208         G92 E0                  ;zero the extruded length
 209         G1 F200 E10             ;extrude 10mm of feed stock
 210         G92 E0                  ;zero the extruded length again
 211         G1 F200 E-{retraction_dual_amount}
 212         T1                      ;Switch to the 2nd extruder
 213         G92 E0                  ;zero the extruded length
 214         G1 F200 E10             ;extrude 10mm of feed stock
 215         G92 E0                  ;zero the extruded length again
 216         G1 F200 E-{retraction_dual_amount}
 217         T0                      ;Switch to the first extruder
 218         G92 E0                  ;zero the extruded length
 219         G1 F200 E10             ;extrude 10mm of feed stock
 220         G92 E0                  ;zero the extruded length again
 221         G1 F{travel_speed}
 222         ;Put printing message on LCD screen
 223         M117 Printing...
 224 end3.gcode = ;End GCode
 225         M104 T0 S0                     ;extruder heater off
 226         M104 T1 S0                     ;extruder heater off
 227         M104 T2 S0                     ;extruder heater off
 228         M140 S0                     ;heated bed heater off (if you have it)
 229         G91                                    ;relative positioning
 230         G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
 231         G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
 232         G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way
 233         M84                         ;steppers off
 234         G90                         ;absolute positioning
 235         ;{profile_string}
 236 start4.gcode = ;Sliced at: {day} {date} {time}
 237         ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
 238         ;Print time: {print_time}
 239         ;Filament used: {filament_amount}m {filament_weight}g
 240         ;Filament cost: {filament_cost}
 241         ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
 242         ;M104 S{print_temperature} ;Uncomment to add your own temperature line
 243         ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
 244         ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
 245         ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
 246         G21        ;metric values
 247         G90        ;absolute positioning
 248         M107       ;start with the fan off
 249         G28 X0 Y0  ;move X/Y to min endstops
 250         G28 Z0     ;move Z to min endstops
 251         G1 Z15.0 F{travel_speed} ;move the platform down 15mm
 252         T3                      ;Switch to the 4th extruder
 253         G92 E0                  ;zero the extruded length
 254         G1 F200 E10             ;extrude 10mm of feed stock
 255         G92 E0                  ;zero the extruded length again
 256         G1 F200 E-{retraction_dual_amount}
 257         T2                      ;Switch to the 3th extruder
 258         G92 E0                  ;zero the extruded length
 259         G1 F200 E10             ;extrude 10mm of feed stock
 260         G92 E0                  ;zero the extruded length again
 261         G1 F200 E-{retraction_dual_amount}
 262         T1                      ;Switch to the 2nd extruder
 263         G92 E0                  ;zero the extruded length
 264         G1 F200 E10             ;extrude 10mm of feed stock
 265         G92 E0                  ;zero the extruded length again
 266         G1 F200 E-{retraction_dual_amount}
 267         T0                      ;Switch to the first extruder
 268         G92 E0                  ;zero the extruded length
 269         G1 F200 E10             ;extrude 10mm of feed stock
 270         G92 E0                  ;zero the extruded length again
 271         G1 F{travel_speed}
 272         ;Put printing message on LCD screen
 273         M117 Printing...
 274 end4.gcode = ;End GCode
 275         M104 T0 S0                     ;extruder heater off
 276         M104 T1 S0                     ;extruder heater off
 277         M104 T2 S0                     ;extruder heater off
 278         M104 T3 S0                     ;extruder heater off
 279         M140 S0                     ;heated bed heater off (if you have it)
 280         G91                                    ;relative positioning
 281         G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
 282         G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
 283         G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way
 284         M84                         ;steppers off
 285         G90                         ;absolute positioning
 286         ;{profile_string}
 287 support_start.gcode =
 288 support_end.gcode =
 289 cool_start.gcode =
 290 cool_end.gcode =
 291 replace.csv =
 292 preswitchextruder.gcode = ;Switch between the current extruder and the next ex
 293 postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
 294         ;This code is added after the T(n)
 295