resources/quickprint/lulzbot_profiles/Mini_single_extruder_v2/PC-ABS_high-speed_Mini_single-extruder-v2_0.5noz_cura.ini

   1 [profile]
   2 layer_height = 0.38
   3 wall_thickness = 1.0
   4 retraction_enable = True
   5 solid_layer_thickness = 0.8
   6 fill_density = 40
   7 perimeter_before_infill = True
   8 nozzle_size = 0.5
   9 print_speed = 50
  10 print_temperature = 275
  11 print_temperature2 = 0
  12 print_temperature3 = 0
  13 print_temperature4 = 0
  14 print_temperature5 = 0
  15 print_bed_temperature = 110
  16 support = None
  17 platform_adhesion = None
  18 support_dual_extrusion = Both
  19 wipe_tower = False
  20 wipe_tower_volume = 15
  21 ooze_shield = False
  22 filament_diameter = 2.85
  23 filament_diameter2 = 0
  24 filament_diameter3 = 0
  25 filament_diameter4 = 0
  26 filament_diameter5 = 0
  27 filament_flow = 100.0
  28 retraction_speed = 10
  29 retraction_amount = 1
  30 retraction_dual_amount = 16.5
  31 retraction_min_travel = 1.5
  32 retraction_combing = All
  33 retraction_minimal_extrusion = 0.005
  34 retraction_hop = 0.1
  35 bottom_thickness = 0.425
  36 layer0_width_factor = 125
  37 object_sink = 0.0
  38 overlap_dual = 0.15
  39 travel_speed = 175
  40 bottom_layer_speed = 15
  41 infill_speed = 60
  42 solidarea_speed = 40
  43 inset0_speed = 50
  44 insetx_speed = 55
  45 cool_min_layer_time = 10
  46 fan_enabled = False
  47 skirt_line_count = 1
  48 skirt_gap = 3.0
  49 skirt_minimal_length = 250
  50 fan_full_height = 0.5
  51 fan_speed = 0
  52 fan_speed_max = 0
  53 cool_min_feedrate = 10
  54 cool_head_lift = False
  55 solid_top = True
  56 solid_bottom = True
  57 fill_overlap = 15
  58 support_type = Lines
  59 support_angle = 45
  60 support_fill_rate = 30
  61 support_xy_distance = 0.7
  62 support_z_distance = 0.05
  63 spiralize = False
  64 simple_mode = False
  65 brim_line_count = 10
  66 raft_margin = 5.0
  67 raft_line_spacing = 3.0
  68 raft_base_thickness = 0.3
  69 raft_base_linewidth = 1.0
  70 raft_interface_thickness = 0.27
  71 raft_interface_linewidth = 0.4
  72 raft_airgap_all = 0.0
  73 raft_airgap = 0.5
  74 raft_surface_layers = 2
  75 raft_surface_thickness = 0.27
  76 raft_surface_linewidth = 0.4
  77 fix_horrible_union_all_type_a = True
  78 fix_horrible_union_all_type_b = False
  79 fix_horrible_use_open_bits = False
  80 fix_horrible_extensive_stitching = False
  81 plugin_config = (lp1
  82         .
  83 object_center_x = -1
  84 object_center_y = -1
  85 simplemodesettings =
  86 simplemodeprofile = 2_normal
  87 simplemodematerial = 1_pla
  88
  89 [alterations]
  90 start.gcode = ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
  91         ;Print time: {print_time}
  92         ;Filament used: {filament_amount}m {filament_weight}g
  93         ;Filament cost: {filament_cost}
  94         ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
  95         ;M109 S{print_temperature} ;Uncomment to add your own temperature line
  96         G21                          ; metric values
  97         G90                          ; absolute positioning
  98         M82                          ; set extruder to absolute mode
  99         M107                         ; start with the fan off
 100         G92 E0                       ; set extruder position to 0
 101         M140 S{print_bed_temperature}; get bed heating up
 102         G28                          ; home all
 103         M109 S150                    ; set to cleaning temp and wait
 104         G1 Z150 E-30 F75             ; suck up XXmm of filament
 105         M109 S170                    ; heat up rest of way
 106         G1 X45 Y174 F11520           ; move behind scraper
 107         G1 Z0  F1200                 ; CRITICAL: set Z to height of top of scraper
 108         G1 X45 Y174 Z-.5 F4000       ; wiping ; plunge into wipe pad
 109         G1 X55 Y172 Z-.5 F4000       ; wiping
 110         G1 X45 Y174 Z0 F4000         ; wiping
 111         G1 X55 Y172 F4000            ; wiping
 112         G1 X45 Y174 F4000            ; wiping
 113         G1 X55 Y172 F4000            ; wiping
 114         G1 X45 Y174 F4000            ; wiping
 115         G1 X55 Y172 F4000            ; wiping
 116         G1 X60 Y174 F4000            ; wiping
 117         G1 X80 Y172 F4000            ; wiping
 118         G1 X60 Y174 F4000            ; wiping
 119         G1 X80 Y172 F4000            ; wiping
 120         G1 X60 Y174 F4000            ; wiping
 121         G1 X90 Y172 F4000            ; wiping
 122         G1 X80 Y174 F4000            ; wiping
 123         G1 X100 Y172 F4000           ; wiping
 124         G1 X80 Y174 F4000            ; wiping
 125         G1 X100 Y172 F4000           ; wiping
 126         G1 X80 Y174 F4000            ; wiping
 127         G1 X100 Y172 F4000           ; wiping
 128         G1 X110 Y174 F4000           ; wiping
 129         G1 X100 Y172 F4000           ; wiping
 130         G1 X110 Y174 F4000           ; wiping
 131         G1 X100 Y172 F4000           ; wiping
 132         G1 X110 Y174 F4000           ; wiping
 133         G1 X115 Y172 Z-0.5 F1000     ; wipe slower and bury noz in cleanish area
 134         G1 Z10                       ; raise z
 135         G28 X0 Y0                    ; home x and y
 136         M109 S170                    ; set to probing temp
 137         M204 S300                    ; set accel for probing
 138         G29                          ; Probe
 139         M204 S2000                   ; set accel back to normal
 140         G1 X5 Y15 Z10 F5000          ; get out the way
 141         M400                         ; clear buffer
 142         G4 S1                        ; pause
 143         M109 S{print_temperature}    ; set extruder temp and wait
 144         G4 S25                       ; wait for bed to temp up
 145         G1 Z2 E0 F75                 ; extrude filament back into nozzle
 146         M140 S{print_bed_temperature}; get bed temping up during first layer
 147 end.gcode =
 148     M400
 149     M104 S0                                      ; hotend off
 150     M140 S0                                      ; heated bed heater off (if you have it)
 151     M107                                         ; fans off
 152     G92 E5                                       ; set extruder to 5mm for retract on print end
 153     G1 X5 Y5 Z158 E0 F10000                      ; move to cooling positioning
 154     M190 R60                                     ; wait for bed to cool
 155     M140 S0                                      ;
 156     G1 X145 F1000                                ; move to cooling positioning
 157     G1 Y175 F1000                                ; move to cooling positioning
 158     M84                                          ; steppers off
 159     G90                                          ; absolute positioning
 160     ;{profile_string}
 161 start2.gcode = ;Sliced at: {day} {date} {time}
 162         ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
 163         ;Print time: {print_time}
 164         ;Filament used: {filament_amount}m {filament_weight}g
 165         ;Filament cost: {filament_cost}
 166         ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
 167         ;M104 S{print_temperature} ;Uncomment to add your own temperature line
 168         ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
 169         ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
 170         G21        ;metric values
 171         G90        ;absolute positioning
 172         M107       ;start with the fan off
 173         G28 X0 Y0  ;move X/Y to min endstops
 174         G28 Z0     ;move Z to min endstops
 175         G1 Z15.0 F{travel_speed} ;move the platform down 15mm
 176         T1                      ;Switch to the 2nd extruder
 177         G92 E0                  ;zero the extruded length
 178         G1 F200 E10             ;extrude 10mm of feed stock
 179         G92 E0                  ;zero the extruded length again
 180         G1 F200 E-{retraction_dual_amount}
 181         T0                      ;Switch to the first extruder
 182         G92 E0                  ;zero the extruded length
 183         G1 F200 E10             ;extrude 10mm of feed stock
 184         G92 E0                  ;zero the extruded length again
 185         G1 F{travel_speed}
 186         ;Put printing message on LCD screen
 187         M117 Printing...
 188 end2.gcode = ;End GCode
 189         M104 T0 S0                     ;extruder heater off
 190         M104 T1 S0                     ;extruder heater off
 191         M140 S0                     ;heated bed heater off (if you have it)
 192         G91                                    ;relative positioning
 193         G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
 194         G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
 195         G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way
 196         M84                         ;steppers off
 197         G90                         ;absolute positioning
 198         ;{profile_string}
 199 start3.gcode = ;Sliced at: {day} {date} {time}
 200         ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
 201         ;Print time: {print_time}
 202         ;Filament used: {filament_amount}m {filament_weight}g
 203         ;Filament cost: {filament_cost}
 204         ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
 205         ;M104 S{print_temperature} ;Uncomment to add your own temperature line
 206         ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
 207         ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
 208         G21        ;metric values
 209         G90        ;absolute positioning
 210         M107       ;start with the fan off
 211         G28 X0 Y0  ;move X/Y to min endstops
 212         G28 Z0     ;move Z to min endstops
 213         G1 Z15.0 F{travel_speed} ;move the platform down 15mm
 214         T2                      ;Switch to the 2nd extruder
 215         G92 E0                  ;zero the extruded length
 216         G1 F200 E10             ;extrude 10mm of feed stock
 217         G92 E0                  ;zero the extruded length again
 218         G1 F200 E-{retraction_dual_amount}
 219         T1                      ;Switch to the 2nd extruder
 220         G92 E0                  ;zero the extruded length
 221         G1 F200 E10             ;extrude 10mm of feed stock
 222         G92 E0                  ;zero the extruded length again
 223         G1 F200 E-{retraction_dual_amount}
 224         T0                      ;Switch to the first extruder
 225         G92 E0                  ;zero the extruded length
 226         G1 F200 E10             ;extrude 10mm of feed stock
 227         G92 E0                  ;zero the extruded length again
 228         G1 F{travel_speed}
 229         ;Put printing message on LCD screen
 230         M117 Printing...
 231 end3.gcode = ;End GCode
 232         M104 T0 S0                     ;extruder heater off
 233         M104 T1 S0                     ;extruder heater off
 234         M104 T2 S0                     ;extruder heater off
 235         M140 S0                     ;heated bed heater off (if you have it)
 236         G91                                    ;relative positioning
 237         G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
 238         G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
 239         G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way
 240         M84                         ;steppers off
 241         G90                         ;absolute positioning
 242         ;{profile_string}
 243 start4.gcode = ;Sliced at: {day} {date} {time}
 244         ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
 245         ;Print time: {print_time}
 246         ;Filament used: {filament_amount}m {filament_weight}g
 247         ;Filament cost: {filament_cost}
 248         ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
 249         ;M104 S{print_temperature} ;Uncomment to add your own temperature line
 250         ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
 251         ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
 252         ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
 253         G21        ;metric values
 254         G90        ;absolute positioning
 255         M107       ;start with the fan off
 256         G28 X0 Y0  ;move X/Y to min endstops
 257         G28 Z0     ;move Z to min endstops
 258         G1 Z15.0 F{travel_speed} ;move the platform down 15mm
 259         T3                      ;Switch to the 4th extruder
 260         G92 E0                  ;zero the extruded length
 261         G1 F200 E10             ;extrude 10mm of feed stock
 262         G92 E0                  ;zero the extruded length again
 263         G1 F200 E-{retraction_dual_amount}
 264         T2                      ;Switch to the 3th extruder
 265         G92 E0                  ;zero the extruded length
 266         G1 F200 E10             ;extrude 10mm of feed stock
 267         G92 E0                  ;zero the extruded length again
 268         G1 F200 E-{retraction_dual_amount}
 269         T1                      ;Switch to the 2nd extruder
 270         G92 E0                  ;zero the extruded length
 271         G1 F200 E10             ;extrude 10mm of feed stock
 272         G92 E0                  ;zero the extruded length again
 273         G1 F200 E-{retraction_dual_amount}
 274         T0                      ;Switch to the first extruder
 275         G92 E0                  ;zero the extruded length
 276         G1 F200 E10             ;extrude 10mm of feed stock
 277         G92 E0                  ;zero the extruded length again
 278         G1 F{travel_speed}
 279         ;Put printing message on LCD screen
 280         M117 Printing...
 281 end4.gcode = ;End GCode
 282         M104 T0 S0                     ;extruder heater off
 283         M104 T1 S0                     ;extruder heater off
 284         M104 T2 S0                     ;extruder heater off
 285         M104 T3 S0                     ;extruder heater off
 286         M140 S0                     ;heated bed heater off (if you have it)
 287         G91                                    ;relative positioning
 288         G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
 289         G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
 290         G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way
 291         M84                         ;steppers off
 292         G90                         ;absolute positioning
 293         ;{profile_string}
 294 support_start.gcode =
 295 support_end.gcode =
 296 cool_start.gcode =
 297 cool_end.gcode =
 298 replace.csv =
 299 preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
 300         ;This code is added before the T(n)
 301 postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
 302         ;This code is added after the T(n)
 303