4 retraction_enable = True
5 solid_layer_thickness = 0.65
7 perimeter_before_infill = True
10 print_temperature = 227
11 print_temperature2 = 0
12 print_temperature3 = 0
13 print_temperature4 = 0
14 print_temperature5 = 0
15 print_bed_temperature = 50
17 platform_adhesion = None
18 support_dual_extrusion = Both
20 wipe_tower_volume = 15
22 filament_diameter = 2.90
23 filament_diameter2 = 0
24 filament_diameter3 = 0
25 filament_diameter4 = 0
26 filament_diameter5 = 0
30 retraction_dual_amount = 16.5
31 retraction_min_travel = 1.5
32 retraction_combing = All
33 retraction_minimal_extrusion = 0.005
35 bottom_thickness = 0.4
36 layer0_width_factor = 125
40 bottom_layer_speed = 8
45 cool_min_layer_time = 20
49 skirt_minimal_length = 250
53 cool_min_feedrate = 10
54 cool_head_lift = False
60 support_fill_rate = 30
61 support_xy_distance = 0.7
62 support_z_distance = 0.05
67 raft_line_spacing = 3.0
68 raft_base_thickness = 0.3
69 raft_base_linewidth = 1.0
70 raft_interface_thickness = 0.27
71 raft_interface_linewidth = 0.4
74 raft_surface_layers = 2
75 raft_surface_thickness = 0.27
76 raft_surface_linewidth = 0.4
77 fix_horrible_union_all_type_a = True
78 fix_horrible_union_all_type_b = False
79 fix_horrible_use_open_bits = False
80 fix_horrible_extensive_stitching = False
85 simplemodeprofile = 2_normal
86 simplemodematerial = 1_pla
87 simplemodematerialtype = Beginner
90 start.gcode = ;This Gcode has been generated specifically for the LulzBot Mini
91 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
92 ;Filament Diameter: {filament_diameter}
93 ;Nozzle Size: {nozzle_size}
95 G90 ; absolute positioning
96 M82 ; set extruder to absolute mode
97 M107 ; start with the fan off
98 G92 E0 ; set extruder position to 0
99 M140 S{print_bed_temperature}; get bed heating up
101 M907 X675 ; reduce extruder torque for safety
102 M109 S160 ; set to cleaning temp and wait
103 G1 Z150 E-30 F45 ; suck up XXmm of filament
104 M109 S170 ; heat up rest of way
105 G1 X45 Y174 F11520 ; move behind scraper
106 G1 Z0 F1200 ; CRITICAL: set Z to height of top of scraper
107 G1 X45 Y174 Z-.5 F4000 ; wiping ; plunge into wipe pad
108 G1 X55 Y172 Z-.5 F4000 ; wiping
109 G1 X45 Y174 Z0 F4000 ; wiping
110 G1 X55 Y172 F4000 ; wiping
111 G1 X45 Y174 F4000 ; wiping
112 G1 X55 Y172 F4000 ; wiping
113 G1 X45 Y174 F4000 ; wiping
114 G1 X55 Y172 F4000 ; wiping
115 G1 X60 Y174 F4000 ; wiping
116 G1 X80 Y172 F4000 ; wiping
117 G1 X60 Y174 F4000 ; wiping
118 G1 X80 Y172 F4000 ; wiping
119 G1 X60 Y174 F4000 ; wiping
120 G1 X90 Y172 F4000 ; wiping
121 G1 X80 Y174 F4000 ; wiping
122 G1 X100 Y172 F4000 ; wiping
123 G1 X80 Y174 F4000 ; wiping
124 G1 X100 Y172 F4000 ; wiping
125 G1 X80 Y174 F4000 ; wiping
126 G1 X100 Y172 F4000 ; wiping
127 G1 X110 Y174 F4000 ; wiping
128 G1 X100 Y172 F4000 ; wiping
129 G1 X110 Y174 F4000 ; wiping
130 G1 X100 Y172 F4000 ; wiping
131 G1 X110 Y174 F4000 ; wiping
132 G1 X115 Y172 Z-0.5 F1000 ; wipe slower and bury noz in cleanish area
134 G28 X0 Y0 ; home x and y
135 M109 S180 ; set to probing temp
136 M204 S300 ; Set probing acceleration
138 M204 S2000 ; Restore standard acceleration
139 G1 X5 Y15 Z10 F5000 ; get out the way
142 M109 S{print_temperature} ; set extruder temp and wait
143 G4 S15 ; wait for bed to temp up
144 G1 Z2 E0 F45 ; extrude filament back into nozzle
145 M140 S{print_bed_temperature}; get bed temping up during first layer
149 M140 S0 ; heated bed heater off (if you have it)
151 G92 E5 ; set extruder to 5mm for retract on print end
152 G1 X5 Y5 Z158 E0 F10000 ; move to cooling positioning
153 G1 X145 F1000 ; move to cooling positioning
154 G1 Y175 F1000 ; move to cooling positioning
156 G90 ; absolute positioning
158 start2.gcode = ;Sliced at: {day} {date} {time}
159 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
160 ;Print time: {print_time}
161 ;Filament used: {filament_amount}m {filament_weight}g
162 ;Filament cost: {filament_cost}
163 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
164 ;M104 S{print_temperature} ;Uncomment to add your own temperature line
165 ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
166 ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
168 G90 ;absolute positioning
169 M107 ;start with the fan off
170 G28 X0 Y0 ;move X/Y to min endstops
171 G28 Z0 ;move Z to min endstops
172 G1 Z15.0 F{travel_speed} ;move the platform down 15mm
173 T1 ;Switch to the 2nd extruder
174 G92 E0 ;zero the extruded length
175 G1 F200 E10 ;extrude 10mm of feed stock
176 G92 E0 ;zero the extruded length again
177 G1 F200 E-{retraction_dual_amount}
178 T0 ;Switch to the first extruder
179 G92 E0 ;zero the extruded length
180 G1 F200 E10 ;extrude 10mm of feed stock
181 G92 E0 ;zero the extruded length again
183 ;Put printing message on LCD screen
185 end2.gcode = ;End GCode
186 M104 T0 S0 ;extruder heater off
187 M104 T1 S0 ;extruder heater off
188 M140 S0 ;heated bed heater off (if you have it)
189 G91 ;relative positioning
190 G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
191 G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
192 G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
194 G90 ;absolute positioning
196 start3.gcode = ;Sliced at: {day} {date} {time}
197 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
198 ;Print time: {print_time}
199 ;Filament used: {filament_amount}m {filament_weight}g
200 ;Filament cost: {filament_cost}
201 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
202 ;M104 S{print_temperature} ;Uncomment to add your own temperature line
203 ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
204 ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
206 G90 ;absolute positioning
207 M107 ;start with the fan off
208 G28 X0 Y0 ;move X/Y to min endstops
209 G28 Z0 ;move Z to min endstops
210 G1 Z15.0 F{travel_speed} ;move the platform down 15mm
211 T2 ;Switch to the 2nd extruder
212 G92 E0 ;zero the extruded length
213 G1 F200 E10 ;extrude 10mm of feed stock
214 G92 E0 ;zero the extruded length again
215 G1 F200 E-{retraction_dual_amount}
216 T1 ;Switch to the 2nd extruder
217 G92 E0 ;zero the extruded length
218 G1 F200 E10 ;extrude 10mm of feed stock
219 G92 E0 ;zero the extruded length again
220 G1 F200 E-{retraction_dual_amount}
221 T0 ;Switch to the first extruder
222 G92 E0 ;zero the extruded length
223 G1 F200 E10 ;extrude 10mm of feed stock
224 G92 E0 ;zero the extruded length again
226 ;Put printing message on LCD screen
228 end3.gcode = ;End GCode
229 M104 T0 S0 ;extruder heater off
230 M104 T1 S0 ;extruder heater off
231 M104 T2 S0 ;extruder heater off
232 M140 S0 ;heated bed heater off (if you have it)
233 G91 ;relative positioning
234 G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
235 G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
236 G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
238 G90 ;absolute positioning
240 start4.gcode = ;Sliced at: {day} {date} {time}
241 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
242 ;Print time: {print_time}
243 ;Filament used: {filament_amount}m {filament_weight}g
244 ;Filament cost: {filament_cost}
245 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
246 ;M104 S{print_temperature} ;Uncomment to add your own temperature line
247 ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
248 ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
249 ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
251 G90 ;absolute positioning
252 M107 ;start with the fan off
253 G28 X0 Y0 ;move X/Y to min endstops
254 G28 Z0 ;move Z to min endstops
255 G1 Z15.0 F{travel_speed} ;move the platform down 15mm
256 T3 ;Switch to the 4th extruder
257 G92 E0 ;zero the extruded length
258 G1 F200 E10 ;extrude 10mm of feed stock
259 G92 E0 ;zero the extruded length again
260 G1 F200 E-{retraction_dual_amount}
261 T2 ;Switch to the 3th extruder
262 G92 E0 ;zero the extruded length
263 G1 F200 E10 ;extrude 10mm of feed stock
264 G92 E0 ;zero the extruded length again
265 G1 F200 E-{retraction_dual_amount}
266 T1 ;Switch to the 2nd extruder
267 G92 E0 ;zero the extruded length
268 G1 F200 E10 ;extrude 10mm of feed stock
269 G92 E0 ;zero the extruded length again
270 G1 F200 E-{retraction_dual_amount}
271 T0 ;Switch to the first extruder
272 G92 E0 ;zero the extruded length
273 G1 F200 E10 ;extrude 10mm of feed stock
274 G92 E0 ;zero the extruded length again
276 ;Put printing message on LCD screen
278 end4.gcode = ;End GCode
279 M104 T0 S0 ;extruder heater off
280 M104 T1 S0 ;extruder heater off
281 M104 T2 S0 ;extruder heater off
282 M104 T3 S0 ;extruder heater off
283 M140 S0 ;heated bed heater off (if you have it)
284 G91 ;relative positioning
285 G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
286 G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
287 G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
289 G90 ;absolute positioning
291 support_start.gcode =
296 preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
297 ;This code is added before the T(n)
298 postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
299 ;This code is added after the T(n)