7 retraction_enable = True
8 solid_layer_thickness = 1.2
12 print_temperature = 240
13 print_temperature2 = 0
14 print_temperature3 = 0
15 print_temperature4 = 0
16 print_bed_temperature = 60
18 platform_adhesion = None
19 support_dual_extrusion = Second extruder
21 wipe_tower_volume = 15
23 filament_diameter = 2.89
24 filament_diameter2 = 2.89
25 filament_diameter3 = 0
26 filament_diameter4 = 0
30 retraction_dual_amount = 25
31 retraction_min_travel = 1.5
32 retraction_combing = True
33 retraction_minimal_extrusion = 0.02
36 layer0_width_factor = 200
40 bottom_layer_speed = 10
44 cool_min_layer_time = 45
48 skirt_minimal_length = 0
53 cool_head_lift = False
59 support_fill_rate = 30
60 support_xy_distance = 0
61 support_z_distance = 0
66 raft_line_spacing = 1.0
67 raft_base_thickness = .5
68 raft_base_linewidth = 0.7
69 raft_interface_thickness = 0.2
70 raft_interface_linewidth = 0.2
72 raft_surface_layers = 2
73 fix_horrible_union_all_type_a = False
74 fix_horrible_union_all_type_b = False
75 fix_horrible_use_open_bits = False
76 fix_horrible_extensive_stitching = False
83 start.gcode = ;This Gcode has been generated specifically for the LulzBot Mini
84 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
85 ;Filament Diameter: {filament_diameter}
86 ;Nozzle Size: {nozzle_size}
88 G90 ; absolute positioning
89 M82 ; set extruder to absolute mode
90 M107 ; start with the fan off
91 G92 E0 ; set extruder position to 0
92 M140 S{print_bed_temperature}; get bed heating up
94 M109 S140 ; set to cleaning temp and wait
95 G1 Z150 E-30 F75 ; suck up XXmm of filament
96 M109 S160 ; heat up rest of way
97 G1 X45 Y174 F11520 ; move behind scraper
98 G1 Z0 F1200 ; CRITICAL: set Z to height of top of scraper
99 G1 X45 Y174 Z-.5 F4000 ; wiping ; plunge into wipe pad
100 G1 X55 Y172 Z-.5 F4000 ; wiping
101 G1 X45 Y174 Z0 F4000 ; wiping
102 G1 X55 Y172 F4000 ; wiping
103 G1 X45 Y174 F4000 ; wiping
104 G1 X55 Y172 F4000 ; wiping
105 G1 X45 Y174 F4000 ; wiping
106 G1 X55 Y172 F4000 ; wiping
107 G1 X60 Y174 F4000 ; wiping
108 G1 X80 Y172 F4000 ; wiping
109 G1 X60 Y174 F4000 ; wiping
110 G1 X80 Y172 F4000 ; wiping
111 G1 X60 Y174 F4000 ; wiping
112 G1 X90 Y172 F4000 ; wiping
113 G1 X80 Y174 F4000 ; wiping
114 G1 X100 Y172 F4000 ; wiping
115 G1 X80 Y174 F4000 ; wiping
116 G1 X100 Y172 F4000 ; wiping
117 G1 X80 Y174 F4000 ; wiping
118 G1 X100 Y172 F4000 ; wiping
119 G1 X110 Y174 F4000 ; wiping
120 G1 X100 Y172 F4000 ; wiping
121 G1 X110 Y174 F4000 ; wiping
122 G1 X100 Y172 F4000 ; wiping
123 G1 X110 Y174 F4000 ; wiping
124 G1 X115 Y172 Z-0.5 F1000 ; wipe slower and bury noz in cleanish area
126 G28 X0 Y0 ; home x and y
127 M109 S160 ; set to probing temp
128 M204 S300 ; Set probing acceleration
130 M204 S2000 ; Restore standard acceleration
131 G1 X5 Y15 Z10 F5000 ; get out the way
134 M109 S{print_temperature} ; set extruder temp and wait
135 G4 S15 ; wait for bed to temp up
136 G1 Z2 E0 F75 ; extrude filament back into nozzle
137 M140 S{print_bed_temperature}; get bed temping up during first layer
140 M140 S0 ; heated bed heater off (if you have it)
142 G92 E5 ; set extruder to 5mm for retract on print end
143 G1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning
144 M190 R50 ; wait for bed to cool
146 G1 X145 Y175 Z156 F1000 ; move to cooling positioning
148 G90 ; absolute positioning
150 start2.gcode = ;Sliced at: {day} {date} {time}
151 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
152 ;Print time: {print_time}
153 ;Filament used: {filament_amount}m {filament_weight}g
154 ;Filament cost: {filament_cost}
155 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
156 ;M104 S{print_temperature} ;Uncomment to add your own temperature line
157 ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
158 ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
160 G90 ;absolute positioning
161 M107 ;start with the fan off
162 G28 X0 Y0 ;move X/Y to min endstops
163 G28 Z0 ;move Z to min endstops
164 G1 Z15.0 F{travel_speed} ;move the platform down 15mm
165 T1 ;Switch to the 2nd extruder
166 G92 E0 ;zero the extruded length
167 G1 F200 E10 ;extrude 10mm of feed stock
168 G92 E0 ;zero the extruded length again
169 G1 F200 E-{retraction_dual_amount}
170 T0 ;Switch to the first extruder
171 G92 E0 ;zero the extruded length
172 G1 F200 E10 ;extrude 10mm of feed stock
173 G92 E0 ;zero the extruded length again
175 ;Put printing message on LCD screen
177 end2.gcode = ;End GCode
178 M104 T0 S0 ;extruder heater off
179 M104 T1 S0 ;extruder heater off
180 M140 S0 ;heated bed heater off (if you have it)
181 G91 ;relative positioning
182 G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
183 G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
184 G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
186 G90 ;absolute positioning
187 start3.gcode = ;Sliced at: {day} {date} {time}
188 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
189 ;Print time: {print_time}
190 ;Filament used: {filament_amount}m {filament_weight}g
191 ;Filament cost: {filament_cost}
192 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
193 ;M104 S{print_temperature} ;Uncomment to add your own temperature line
194 ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
195 ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
197 G90 ;absolute positioning
198 M107 ;start with the fan off
199 G28 X0 Y0 ;move X/Y to min endstops
200 G28 Z0 ;move Z to min endstops
201 G1 Z15.0 F{travel_speed} ;move the platform down 15mm
202 T2 ;Switch to the 2nd extruder
203 G92 E0 ;zero the extruded length
204 G1 F200 E10 ;extrude 10mm of feed stock
205 G92 E0 ;zero the extruded length again
206 G1 F200 E-{retraction_dual_amount}
207 T1 ;Switch to the 2nd extruder
208 G92 E0 ;zero the extruded length
209 G1 F200 E10 ;extrude 10mm of feed stock
210 G92 E0 ;zero the extruded length again
211 G1 F200 E-{retraction_dual_amount}
212 T0 ;Switch to the first extruder
213 G92 E0 ;zero the extruded length
214 G1 F200 E10 ;extrude 10mm of feed stock
215 G92 E0 ;zero the extruded length again
217 ;Put printing message on LCD screen
219 end3.gcode = ;End GCode
220 M104 T0 S0 ;extruder heater off
221 M104 T1 S0 ;extruder heater off
222 M104 T2 S0 ;extruder heater off
223 M140 S0 ;heated bed heater off (if you have it)
224 G91 ;relative positioning
225 G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
226 G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
227 G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
229 G90 ;absolute positioning
231 start4.gcode = ;Sliced at: {day} {date} {time}
232 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
233 ;Print time: {print_time}
234 ;Filament used: {filament_amount}m {filament_weight}g
235 ;Filament cost: {filament_cost}
236 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
237 ;M104 S{print_temperature} ;Uncomment to add your own temperature line
238 ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
239 ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
240 ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
242 G90 ;absolute positioning
243 M107 ;start with the fan off
244 G28 X0 Y0 ;move X/Y to min endstops
245 G28 Z0 ;move Z to min endstops
246 G1 Z15.0 F{travel_speed} ;move the platform down 15mm
247 T3 ;Switch to the 4th extruder
248 G92 E0 ;zero the extruded length
249 G1 F200 E10 ;extrude 10mm of feed stock
250 G92 E0 ;zero the extruded length again
251 G1 F200 E-{retraction_dual_amount}
252 T2 ;Switch to the 3th extruder
253 G92 E0 ;zero the extruded length
254 G1 F200 E10 ;extrude 10mm of feed stock
255 G92 E0 ;zero the extruded length again
256 G1 F200 E-{retraction_dual_amount}
257 T1 ;Switch to the 2nd extruder
258 G92 E0 ;zero the extruded length
259 G1 F200 E10 ;extrude 10mm of feed stock
260 G92 E0 ;zero the extruded length again
261 G1 F200 E-{retraction_dual_amount}
262 T0 ;Switch to the first extruder
263 G92 E0 ;zero the extruded length
264 G1 F200 E10 ;extrude 10mm of feed stock
265 G92 E0 ;zero the extruded length again
267 ;Put printing message on LCD screen
269 end4.gcode = ;End GCode
270 M104 T0 S0 ;extruder heater off
271 M104 T1 S0 ;extruder heater off
272 M104 T2 S0 ;extruder heater off
273 M104 T3 S0 ;extruder heater off
274 M140 S0 ;heated bed heater off (if you have it)
275 G91 ;relative positioning
276 G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
277 G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
278 G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
280 G90 ;absolute positioning
282 support_start.gcode =
287 preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
288 ;This code is added before the T(n)
289 postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
290 ;This code is added after the T(n)