resources/quickprint/lulzbot_mini/ABS/Normal/profile.ini

   1 [info]
   2 name = Normal Quality
   3 order = 1
   4 default = 1
   5
   6 [profile]
   7 layer_height = 0.25
   8 wall_thickness = 1.0
   9 retraction_enable = True
  10 solid_layer_thickness = 0.8
  11 fill_density = 20
  12 nozzle_size = 0.5
  13 print_speed = 50
  14 print_temperature = 240
  15 print_temperature2 = 0
  16 print_temperature3 = 0
  17 print_temperature4 = 0
  18 print_bed_temperature = 110
  19 support = None
  20 platform_adhesion = None
  21 support_dual_extrusion = Both
  22 wipe_tower = False
  23 wipe_tower_volume = 15
  24 ooze_shield = False
  25 filament_diameter = 2.85
  26 filament_diameter2 = 0
  27 filament_diameter3 = 0
  28 filament_diameter4 = 0
  29 filament_flow = 100.0
  30 retraction_speed = 10
  31 retraction_amount = 1
  32 retraction_dual_amount = 16.5
  33 retraction_min_travel = 1.5
  34 retraction_combing = True
  35 retraction_minimal_extrusion = 0.005
  36 retraction_hop = 0.1
  37 bottom_thickness = 0.425
  38 layer0_width_factor = 125
  39 object_sink = 0.0
  40 overlap_dual = 0.15
  41 travel_speed = 175
  42 bottom_layer_speed = 15
  43 infill_speed = 55
  44 inset0_speed = 45
  45 insetx_speed = 50
  46 cool_min_layer_time = 15
  47 fan_enabled = True
  48 skirt_line_count = 1
  49 skirt_gap = 3.0
  50 skirt_minimal_length = 250
  51 fan_full_height = 0.5
  52 fan_speed = 40
  53 fan_speed_max = 60
  54 cool_min_feedrate = 10
  55 cool_head_lift = False
  56 solid_top = True
  57 solid_bottom = True
  58 fill_overlap = 15
  59 support_type = Lines
  60 support_angle = 45
  61 support_fill_rate = 30
  62 support_xy_distance = 0.7
  63 support_z_distance = 0.05
  64 spiralize = False
  65 simple_mode = False
  66 brim_line_count = 10
  67 raft_margin = 5.0
  68 raft_line_spacing = 3.0
  69 raft_base_thickness = 0.3
  70 raft_base_linewidth = 1.0
  71 raft_interface_thickness = 0.27
  72 raft_interface_linewidth = 0.4
  73 raft_airgap = 0.5
  74 raft_surface_layers = 2
  75 fix_horrible_union_all_type_a = True
  76 fix_horrible_union_all_type_b = False
  77 fix_horrible_use_open_bits = False
  78 fix_horrible_extensive_stitching = False
  79 plugin_config = (lp1
  80         .
  81 object_center_x = -1
  82 object_center_y = -1
  83
  84 [alterations]
  85 start.gcode = ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
  86         ;Print time: {print_time}
  87         ;Filament used: {filament_amount}m {filament_weight}g
  88         ;Filament cost: {filament_cost}
  89         ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
  90         ;M109 S{print_temperature} ;Uncomment to add your own temperature line
  91         G21                          ; metric values
  92         G90                          ; absolute positioning
  93         M82                          ; set extruder to absolute mode
  94         M107                         ; start with the fan off
  95         G92 E0                       ; set extruder position to 0
  96         M140 S{print_bed_temperature}; get bed heating up
  97         G28                          ; home all
  98         M109 S150                    ; set to cleaning temp and wait
  99         G1 Z150 E-30 F75             ; suck up XXmm of filament
 100         M109 S170                    ; heat up rest of way
 101         G1 X45 Y174 F11520           ; move behind scraper
 102         G1 Z0  F1200                 ; CRITICAL: set Z to height of top of scraper
 103         G1 X45 Y174 Z-.5 F4000       ; wiping ; plunge into wipe pad
 104         G1 X55 Y172 Z-.5 F4000       ; wiping
 105         G1 X45 Y174 Z0 F4000         ; wiping
 106         G1 X55 Y172 F4000            ; wiping
 107         G1 X45 Y174 F4000            ; wiping
 108         G1 X55 Y172 F4000            ; wiping
 109         G1 X45 Y174 F4000            ; wiping
 110         G1 X55 Y172 F4000            ; wiping
 111         G1 X60 Y174 F4000            ; wiping
 112         G1 X80 Y172 F4000            ; wiping
 113         G1 X60 Y174 F4000            ; wiping
 114         G1 X80 Y172 F4000            ; wiping
 115         G1 X60 Y174 F4000            ; wiping
 116         G1 X90 Y172 F4000            ; wiping
 117         G1 X80 Y174 F4000            ; wiping
 118         G1 X100 Y172 F4000           ; wiping
 119         G1 X80 Y174 F4000            ; wiping
 120         G1 X100 Y172 F4000           ; wiping
 121         G1 X80 Y174 F4000            ; wiping
 122         G1 X100 Y172 F4000           ; wiping
 123         G1 X110 Y174 F4000           ; wiping
 124         G1 X100 Y172 F4000           ; wiping
 125         G1 X110 Y174 F4000           ; wiping
 126         G1 X100 Y172 F4000           ; wiping
 127         G1 X110 Y174 F4000           ; wiping
 128         G1 X115 Y172 Z-0.5 F1000     ; wipe slower and bury noz in cleanish area
 129         G1 Z10                       ; raise z
 130         G28 X0 Y0                    ; home x and y
 131         M109 S170                    ; set to probing temp
 132         M204 S300                    ; set accel for probing
 133         G29                          ; Probe
 134         M204 S2000                   ; set accel back to normal
 135         G1 X5 Y15 Z10 F5000          ; get out the way
 136         M400                         ; clear buffer
 137         G4 S1                        ; pause
 138         M109 S{print_temperature}    ; set extruder temp and wait
 139         G4 S25                       ; wait for bed to temp up
 140         G1 Z2 E0 F75                 ; extrude filament back into nozzle
 141         M140 S{print_bed_temperature}; get bed temping up during first layer
 142 end.gcode = M400
 143         M104 S0                         ; Hotend off
 144         M140 S0                         ; heated bed heater off (if you have it)
 145         M107                            ; fans off
 146         G92 E0                          ; set extruder to 0
 147         G1 E-3 F300                     ; retract a bit to relieve pressure
 148         G1 X5 Y5 Z156 F10000            ; move to cooling positioning
 149         M190 R60                        ; wait for bed to cool
 150         M140 S0                         ; turn off bed temp
 151         G1 X145 Y175 Z156 F1000         ; move to cooling positioning
 152         M84                             ; steppers off
 153         G90                             ; absolute positioning
 154         ;{profile_string}
 155 start2.gcode = ;Sliced at: {day} {date} {time}
 156         ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
 157         ;Print time: {print_time}
 158         ;Filament used: {filament_amount}m {filament_weight}g
 159         ;Filament cost: {filament_cost}
 160         ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
 161         ;M104 S{print_temperature} ;Uncomment to add your own temperature line
 162         ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
 163         ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
 164         G21        ;metric values
 165         G90        ;absolute positioning
 166         M107       ;start with the fan off
 167         G28 X0 Y0  ;move X/Y to min endstops
 168         G28 Z0     ;move Z to min endstops
 169         G1 Z15.0 F{travel_speed} ;move the platform down 15mm
 170         T1                      ;Switch to the 2nd extruder
 171         G92 E0                  ;zero the extruded length
 172         G1 F200 E10             ;extrude 10mm of feed stock
 173         G92 E0                  ;zero the extruded length again
 174         G1 F200 E-{retraction_dual_amount}
 175         T0                      ;Switch to the first extruder
 176         G92 E0                  ;zero the extruded length
 177         G1 F200 E10             ;extrude 10mm of feed stock
 178         G92 E0                  ;zero the extruded length again
 179         G1 F{travel_speed}
 180         ;Put printing message on LCD screen
 181         M117 Printing...
 182 end2.gcode = ;End GCode
 183         M104 T0 S0                     ;extruder heater off
 184         M104 T1 S0                     ;extruder heater off
 185         M140 S0                     ;heated bed heater off (if you have it)
 186         G91                                    ;relative positioning
 187         G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
 188         G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
 189         G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way
 190         M84                         ;steppers off
 191         G90                         ;absolute positioning
 192         ;{profile_string}
 193 start3.gcode = ;Sliced at: {day} {date} {time}
 194         ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
 195         ;Print time: {print_time}
 196         ;Filament used: {filament_amount}m {filament_weight}g
 197         ;Filament cost: {filament_cost}
 198         ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
 199         ;M104 S{print_temperature} ;Uncomment to add your own temperature line
 200         ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
 201         ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
 202         G21        ;metric values
 203         G90        ;absolute positioning
 204         M107       ;start with the fan off
 205         G28 X0 Y0  ;move X/Y to min endstops
 206         G28 Z0     ;move Z to min endstops
 207         G1 Z15.0 F{travel_speed} ;move the platform down 15mm
 208         T2                      ;Switch to the 2nd extruder
 209         G92 E0                  ;zero the extruded length
 210         G1 F200 E10             ;extrude 10mm of feed stock
 211         G92 E0                  ;zero the extruded length again
 212         G1 F200 E-{retraction_dual_amount}
 213         T1                      ;Switch to the 2nd extruder
 214         G92 E0                  ;zero the extruded length
 215         G1 F200 E10             ;extrude 10mm of feed stock
 216         G92 E0                  ;zero the extruded length again
 217         G1 F200 E-{retraction_dual_amount}
 218         T0                      ;Switch to the first extruder
 219         G92 E0                  ;zero the extruded length
 220         G1 F200 E10             ;extrude 10mm of feed stock
 221         G92 E0                  ;zero the extruded length again
 222         G1 F{travel_speed}
 223         ;Put printing message on LCD screen
 224         M117 Printing...
 225 end3.gcode = ;End GCode
 226         M104 T0 S0                     ;extruder heater off
 227         M104 T1 S0                     ;extruder heater off
 228         M104 T2 S0                     ;extruder heater off
 229         M140 S0                     ;heated bed heater off (if you have it)
 230         G91                                    ;relative positioning
 231         G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
 232         G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
 233         G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way
 234         M84                         ;steppers off
 235         G90                         ;absolute positioning
 236         ;{profile_string}
 237 start4.gcode = ;Sliced at: {day} {date} {time}
 238         ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
 239         ;Print time: {print_time}
 240         ;Filament used: {filament_amount}m {filament_weight}g
 241         ;Filament cost: {filament_cost}
 242         ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
 243         ;M104 S{print_temperature} ;Uncomment to add your own temperature line
 244         ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
 245         ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
 246         ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
 247         G21        ;metric values
 248         G90        ;absolute positioning
 249         M107       ;start with the fan off
 250         G28 X0 Y0  ;move X/Y to min endstops
 251         G28 Z0     ;move Z to min endstops
 252         G1 Z15.0 F{travel_speed} ;move the platform down 15mm
 253         T3                      ;Switch to the 4th extruder
 254         G92 E0                  ;zero the extruded length
 255         G1 F200 E10             ;extrude 10mm of feed stock
 256         G92 E0                  ;zero the extruded length again
 257         G1 F200 E-{retraction_dual_amount}
 258         T2                      ;Switch to the 3th extruder
 259         G92 E0                  ;zero the extruded length
 260         G1 F200 E10             ;extrude 10mm of feed stock
 261         G92 E0                  ;zero the extruded length again
 262         G1 F200 E-{retraction_dual_amount}
 263         T1                      ;Switch to the 2nd extruder
 264         G92 E0                  ;zero the extruded length
 265         G1 F200 E10             ;extrude 10mm of feed stock
 266         G92 E0                  ;zero the extruded length again
 267         G1 F200 E-{retraction_dual_amount}
 268         T0                      ;Switch to the first extruder
 269         G92 E0                  ;zero the extruded length
 270         G1 F200 E10             ;extrude 10mm of feed stock
 271         G92 E0                  ;zero the extruded length again
 272         G1 F{travel_speed}
 273         ;Put printing message on LCD screen
 274         M117 Printing...
 275 end4.gcode = ;End GCode
 276         M104 T0 S0                     ;extruder heater off
 277         M104 T1 S0                     ;extruder heater off
 278         M104 T2 S0                     ;extruder heater off
 279         M104 T3 S0                     ;extruder heater off
 280         M140 S0                     ;heated bed heater off (if you have it)
 281         G91                                    ;relative positioning
 282         G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
 283         G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
 284         G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way
 285         M84                         ;steppers off
 286         G90                         ;absolute positioning
 287         ;{profile_string}
 288 support_start.gcode =
 289 support_end.gcode =
 290 cool_start.gcode =
 291 cool_end.gcode =
 292 replace.csv =
 293 preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
 294         ;This code is added before the T(n)
 295 postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
 296         ;This code is added after the T(n)
 297