9 retraction_enable = True
10 solid_layer_thickness = 0.8
15 print_temperature2 = 0
16 print_temperature3 = 0
17 print_temperature4 = 0
18 print_bed_temperature = 0
20 platform_adhesion = None
21 support_dual_extrusion = Both
23 wipe_tower_volume = 15
25 filament_diameter = 2.85
26 filament_diameter2 = 0
27 filament_diameter3 = 0
28 filament_diameter4 = 0
32 retraction_dual_amount = 16.5
33 retraction_min_travel = 1.5
34 retraction_combing = All
35 retraction_minimal_extrusion = 0.005
37 bottom_thickness = 0.425
38 layer0_width_factor = 125
42 bottom_layer_speed = 15
46 cool_min_layer_time = 20
50 skirt_minimal_length = 250
54 cool_min_feedrate = 10
55 cool_head_lift = False
61 support_fill_rate = 30
62 support_xy_distance = 0.7
63 support_z_distance = 0.05
68 raft_line_spacing = 3.0
69 raft_base_thickness = 0.3
70 raft_base_linewidth = 1.0
71 raft_interface_thickness = 0.27
72 raft_interface_linewidth = 0.4
74 raft_surface_layers = 2
75 fix_horrible_union_all_type_a = True
76 fix_horrible_union_all_type_b = False
77 fix_horrible_use_open_bits = False
78 fix_horrible_extensive_stitching = False
85 start.gcode = ;Sliced at: {day} {date} {time}
86 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
87 ;Print time: {print_time}
88 ;Filament used: {filament_amount}m {filament_weight}g
89 ;Filament cost: {filament_cost}
90 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
91 ;M109 S{print_temperature} ;Uncomment to add your own temperature line
93 G90 ;absolute positioning
94 M82 ;set extruder to absolute mode
95 M107 ;start with the fan off
96 G28 X0 Y0 ;move X/Y to min endstops
97 G28 Z0 ;move Z to min endstops
98 G1 Z15.0 F{travel_speed};move the platform down 15mm
99 G92 E0 ; zero the extruded length
100 G1 F200 E0 ; extrude 3mm of feed stock
101 G92 E0 ; zero the extruded length again
102 G1 F{travel_speed} ; set travel speed
103 M203 X192 Y208 Z3 ; speed limits
104 M117 Printing... ; send message to LCD
107 M140 S0 ; heated bed heater off (if you have it)
109 G91 ; relative positioning
110 G1 E-1 F300 ; retract the filament a bit before lifting the nozzle, to release some of the pressure
111 G1 Z+0.5 E-5 X-20 Y-20 F3000 ; move Z up a bit and retract filament even more
112 G90 ; absolute positioning
113 G1 X0 Y250 ; move to cooling position
115 G90 ; absolute positioning
118 start2.gcode = ;Sliced at: {day} {date} {time}
119 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
120 ;Print time: {print_time}
121 ;Filament used: {filament_amount}m {filament_weight}g
122 ;Filament cost: {filament_cost}
123 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
124 ;M104 S{print_temperature} ;Uncomment to add your own temperature line
125 ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
126 ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
128 G90 ;absolute positioning
129 M107 ;start with the fan off
130 G28 X0 Y0 ;move X/Y to min endstops
131 G28 Z0 ;move Z to min endstops
132 G1 Z15.0 F{travel_speed} ;move the platform down 15mm
133 T1 ;Switch to the 2nd extruder
134 G92 E0 ;zero the extruded length
135 G1 F200 E10 ;extrude 10mm of feed stock
136 G92 E0 ;zero the extruded length again
137 G1 F200 E-{retraction_dual_amount}
138 T0 ;Switch to the first extruder
139 G92 E0 ;zero the extruded length
140 G1 F200 E10 ;extrude 10mm of feed stock
141 G92 E0 ;zero the extruded length again
143 ;Put printing message on LCD screen
145 end2.gcode = ;End GCode
146 M104 T0 S0 ;extruder heater off
147 M104 T1 S0 ;extruder heater off
148 M140 S0 ;heated bed heater off (if you have it)
149 G91 ;relative positioning
150 G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
151 G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
152 G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
154 G90 ;absolute positioning
156 start3.gcode = ;Sliced at: {day} {date} {time}
157 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
158 ;Print time: {print_time}
159 ;Filament used: {filament_amount}m {filament_weight}g
160 ;Filament cost: {filament_cost}
161 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
162 ;M104 S{print_temperature} ;Uncomment to add your own temperature line
163 ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
164 ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
166 G90 ;absolute positioning
167 M107 ;start with the fan off
168 G28 X0 Y0 ;move X/Y to min endstops
169 G28 Z0 ;move Z to min endstops
170 G1 Z15.0 F{travel_speed} ;move the platform down 15mm
171 T2 ;Switch to the 2nd extruder
172 G92 E0 ;zero the extruded length
173 G1 F200 E10 ;extrude 10mm of feed stock
174 G92 E0 ;zero the extruded length again
175 G1 F200 E-{retraction_dual_amount}
176 T1 ;Switch to the 2nd extruder
177 G92 E0 ;zero the extruded length
178 G1 F200 E10 ;extrude 10mm of feed stock
179 G92 E0 ;zero the extruded length again
180 G1 F200 E-{retraction_dual_amount}
181 T0 ;Switch to the first extruder
182 G92 E0 ;zero the extruded length
183 G1 F200 E10 ;extrude 10mm of feed stock
184 G92 E0 ;zero the extruded length again
186 ;Put printing message on LCD screen
188 end3.gcode = ;End GCode
189 M104 T0 S0 ;extruder heater off
190 M104 T1 S0 ;extruder heater off
191 M104 T2 S0 ;extruder heater off
192 M140 S0 ;heated bed heater off (if you have it)
193 G91 ;relative positioning
194 G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
195 G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
196 G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
198 G90 ;absolute positioning
200 start4.gcode = ;Sliced at: {day} {date} {time}
201 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
202 ;Print time: {print_time}
203 ;Filament used: {filament_amount}m {filament_weight}g
204 ;Filament cost: {filament_cost}
205 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
206 ;M104 S{print_temperature} ;Uncomment to add your own temperature line
207 ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
208 ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
209 ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
211 G90 ;absolute positioning
212 M107 ;start with the fan off
213 G28 X0 Y0 ;move X/Y to min endstops
214 G28 Z0 ;move Z to min endstops
215 G1 Z15.0 F{travel_speed} ;move the platform down 15mm
216 T3 ;Switch to the 4th extruder
217 G92 E0 ;zero the extruded length
218 G1 F200 E10 ;extrude 10mm of feed stock
219 G92 E0 ;zero the extruded length again
220 G1 F200 E-{retraction_dual_amount}
221 T2 ;Switch to the 3th extruder
222 G92 E0 ;zero the extruded length
223 G1 F200 E10 ;extrude 10mm of feed stock
224 G92 E0 ;zero the extruded length again
225 G1 F200 E-{retraction_dual_amount}
226 T1 ;Switch to the 2nd extruder
227 G92 E0 ;zero the extruded length
228 G1 F200 E10 ;extrude 10mm of feed stock
229 G92 E0 ;zero the extruded length again
230 G1 F200 E-{retraction_dual_amount}
231 T0 ;Switch to the first extruder
232 G92 E0 ;zero the extruded length
233 G1 F200 E10 ;extrude 10mm of feed stock
234 G92 E0 ;zero the extruded length again
236 ;Put printing message on LCD screen
238 end4.gcode = ;End GCode
239 M104 T0 S0 ;extruder heater off
240 M104 T1 S0 ;extruder heater off
241 M104 T2 S0 ;extruder heater off
242 M104 T3 S0 ;extruder heater off
243 M140 S0 ;heated bed heater off (if you have it)
244 G91 ;relative positioning
245 G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
246 G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
247 G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
249 G90 ;absolute positioning
251 support_start.gcode =
256 preswitchextruder.gcode = ;Switch between the current extruder and the next ex
257 postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
258 ;This code is added after the T(n)