8 retraction_enable = True
9 solid_layer_thickness = 0.8
14 print_temperature2 = 0
15 print_temperature3 = 0
16 print_temperature4 = 0
17 print_bed_temperature = 0
19 platform_adhesion = None
20 support_dual_extrusion = Both
22 wipe_tower_volume = 15
24 filament_diameter = 2.85
25 filament_diameter2 = 0
26 filament_diameter3 = 0
27 filament_diameter4 = 0
31 retraction_dual_amount = 16.5
32 retraction_min_travel = 1.5
33 retraction_combing = True
34 retraction_minimal_extrusion = 0.005
36 bottom_thickness = 0.425
37 layer0_width_factor = 125
41 bottom_layer_speed = 15
45 cool_min_layer_time = 20
49 skirt_minimal_length = 250
53 cool_min_feedrate = 10
54 cool_head_lift = False
60 support_fill_rate = 30
61 support_xy_distance = 0.7
62 support_z_distance = 0.05
67 raft_line_spacing = 3.0
68 raft_base_thickness = 0.3
69 raft_base_linewidth = 1.0
70 raft_interface_thickness = 0.27
71 raft_interface_linewidth = 0.4
73 raft_surface_layers = 2
74 fix_horrible_union_all_type_a = True
75 fix_horrible_union_all_type_b = False
76 fix_horrible_use_open_bits = False
77 fix_horrible_extensive_stitching = False
84 start.gcode = ;Sliced at: {day} {date} {time}
85 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
86 ;Print time: {print_time}
87 ;Filament used: {filament_amount}m {filament_weight}g
88 ;Filament cost: {filament_cost}
89 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
90 ;M109 S{print_temperature} ;Uncomment to add your own temperature line
92 G90 ;absolute positioning
93 M82 ;set extruder to absolute mode
94 M107 ;start with the fan off
95 G28 X0 Y0 ;move X/Y to min endstops
96 G28 Z0 ;move Z to min endstops
97 G1 Z15.0 F{travel_speed};move the platform down 15mm
98 G92 E0 ; zero the extruded length
99 G1 F200 E0 ; extrude 3mm of feed stock
100 G92 E0 ; zero the extruded length again
101 G1 F{travel_speed} ; set travel speed
102 M203 X192 Y208 Z3 ; speed limits
103 M117 Printing... ; send message to LCD
106 M140 S0 ; heated bed heater off (if you have it)
108 G91 ; relative positioning
109 G1 E-1 F300 ; retract the filament a bit before lifting the nozzle, to release some of the pressure
110 G1 Z+0.5 E-5 X-20 Y-20 F3000 ; move Z up a bit and retract filament even more
111 G90 ; absolute positioning
112 G1 X0 Y250 ; move to cooling position
114 G90 ; absolute positioning
117 start2.gcode = ;Sliced at: {day} {date} {time}
118 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
119 ;Print time: {print_time}
120 ;Filament used: {filament_amount}m {filament_weight}g
121 ;Filament cost: {filament_cost}
122 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
123 ;M104 S{print_temperature} ;Uncomment to add your own temperature line
124 ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
125 ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
127 G90 ;absolute positioning
128 M107 ;start with the fan off
129 G28 X0 Y0 ;move X/Y to min endstops
130 G28 Z0 ;move Z to min endstops
131 G1 Z15.0 F{travel_speed} ;move the platform down 15mm
132 T1 ;Switch to the 2nd extruder
133 G92 E0 ;zero the extruded length
134 G1 F200 E10 ;extrude 10mm of feed stock
135 G92 E0 ;zero the extruded length again
136 G1 F200 E-{retraction_dual_amount}
137 T0 ;Switch to the first extruder
138 G92 E0 ;zero the extruded length
139 G1 F200 E10 ;extrude 10mm of feed stock
140 G92 E0 ;zero the extruded length again
142 ;Put printing message on LCD screen
144 end2.gcode = ;End GCode
145 M104 T0 S0 ;extruder heater off
146 M104 T1 S0 ;extruder heater off
147 M140 S0 ;heated bed heater off (if you have it)
148 G91 ;relative positioning
149 G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
150 G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
151 G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
153 G90 ;absolute positioning
155 start3.gcode = ;Sliced at: {day} {date} {time}
156 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
157 ;Print time: {print_time}
158 ;Filament used: {filament_amount}m {filament_weight}g
159 ;Filament cost: {filament_cost}
160 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
161 ;M104 S{print_temperature} ;Uncomment to add your own temperature line
162 ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
163 ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
165 G90 ;absolute positioning
166 M107 ;start with the fan off
167 G28 X0 Y0 ;move X/Y to min endstops
168 G28 Z0 ;move Z to min endstops
169 G1 Z15.0 F{travel_speed} ;move the platform down 15mm
170 T2 ;Switch to the 2nd extruder
171 G92 E0 ;zero the extruded length
172 G1 F200 E10 ;extrude 10mm of feed stock
173 G92 E0 ;zero the extruded length again
174 G1 F200 E-{retraction_dual_amount}
175 T1 ;Switch to the 2nd extruder
176 G92 E0 ;zero the extruded length
177 G1 F200 E10 ;extrude 10mm of feed stock
178 G92 E0 ;zero the extruded length again
179 G1 F200 E-{retraction_dual_amount}
180 T0 ;Switch to the first extruder
181 G92 E0 ;zero the extruded length
182 G1 F200 E10 ;extrude 10mm of feed stock
183 G92 E0 ;zero the extruded length again
185 ;Put printing message on LCD screen
187 end3.gcode = ;End GCode
188 M104 T0 S0 ;extruder heater off
189 M104 T1 S0 ;extruder heater off
190 M104 T2 S0 ;extruder heater off
191 M140 S0 ;heated bed heater off (if you have it)
192 G91 ;relative positioning
193 G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
194 G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
195 G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
197 G90 ;absolute positioning
199 start4.gcode = ;Sliced at: {day} {date} {time}
200 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
201 ;Print time: {print_time}
202 ;Filament used: {filament_amount}m {filament_weight}g
203 ;Filament cost: {filament_cost}
204 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
205 ;M104 S{print_temperature} ;Uncomment to add your own temperature line
206 ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
207 ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
208 ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
210 G90 ;absolute positioning
211 M107 ;start with the fan off
212 G28 X0 Y0 ;move X/Y to min endstops
213 G28 Z0 ;move Z to min endstops
214 G1 Z15.0 F{travel_speed} ;move the platform down 15mm
215 T3 ;Switch to the 4th extruder
216 G92 E0 ;zero the extruded length
217 G1 F200 E10 ;extrude 10mm of feed stock
218 G92 E0 ;zero the extruded length again
219 G1 F200 E-{retraction_dual_amount}
220 T2 ;Switch to the 3th extruder
221 G92 E0 ;zero the extruded length
222 G1 F200 E10 ;extrude 10mm of feed stock
223 G92 E0 ;zero the extruded length again
224 G1 F200 E-{retraction_dual_amount}
225 T1 ;Switch to the 2nd extruder
226 G92 E0 ;zero the extruded length
227 G1 F200 E10 ;extrude 10mm of feed stock
228 G92 E0 ;zero the extruded length again
229 G1 F200 E-{retraction_dual_amount}
230 T0 ;Switch to the first extruder
231 G92 E0 ;zero the extruded length
232 G1 F200 E10 ;extrude 10mm of feed stock
233 G92 E0 ;zero the extruded length again
235 ;Put printing message on LCD screen
237 end4.gcode = ;End GCode
238 M104 T0 S0 ;extruder heater off
239 M104 T1 S0 ;extruder heater off
240 M104 T2 S0 ;extruder heater off
241 M104 T3 S0 ;extruder heater off
242 M140 S0 ;heated bed heater off (if you have it)
243 G91 ;relative positioning
244 G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
245 G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
246 G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
248 G90 ;absolute positioning
250 support_start.gcode =
255 preswitchextruder.gcode = ;Switch between the current extruder and the next ex
256 postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
257 ;This code is added after the T(n)