8 retraction_enable = True
9 solid_layer_thickness = .7
14 print_temperature2 = 0
15 print_temperature3 = 0
16 print_temperature4 = 0
17 print_bed_temperature = 0
19 platform_adhesion = None
20 support_dual_extrusion = Both
22 wipe_tower_volume = 15
24 filament_diameter = 2.85
25 filament_diameter2 = 0
26 filament_diameter3 = 0
27 filament_diameter4 = 0
31 retraction_dual_amount = 16.5
32 retraction_min_travel = 0.5
33 retraction_combing = True
34 retraction_minimal_extrusion = 0.005
37 layer0_width_factor = 125
41 bottom_layer_speed = 15
45 cool_min_layer_time = 20
49 skirt_minimal_length = 250
53 cool_min_feedrate = 10
54 cool_head_lift = False
60 support_fill_rate = 30
61 support_xy_distance = 0.7
62 support_z_distance = 0.05
67 raft_line_spacing = 3.0
68 raft_base_thickness = 0.3
69 raft_base_linewidth = 1.0
70 raft_interface_thickness = 0.27
71 raft_interface_linewidth = 0.4
73 raft_surface_layers = 2
74 fix_horrible_union_all_type_a = True
75 fix_horrible_union_all_type_b = False
76 fix_horrible_use_open_bits = False
77 fix_horrible_extensive_stitching = False
83 start.gcode = ;Sliced at: {day} {date} {time}
84 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
85 ;Print time: {print_time}
86 ;Filament used: {filament_amount}m {filament_weight}g
87 ;Filament cost: {filament_cost}
88 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
89 ;M109 S{print_temperature} ;Uncomment to add your own temperature line
91 G90 ;absolute positioning
92 M82 ;set extruder to absolute mode
93 M107 ;start with the fan off
94 G28 X0 Y0 ;move X/Y to min endstops
95 G28 Z0 ;move Z to min endstops
96 G1 Z15.0 F{travel_speed};move the platform down 15mm
97 G92 E0 ; zero the extruded length
98 G1 F200 E0 ; extrude 3mm of feed stock
99 G92 E0 ; zero the extruded length again
100 G1 F{travel_speed} ; set travel speed
101 M203 X192 Y208 Z3 ; speed limits
102 M117 Printing... ; send message to LCD
105 M140 S0 ; heated bed heater off (if you have it)
107 G91 ; relative positioning
108 G1 E-1 F300 ; retract the filament a bit before lifting the nozzle, to release some of the pressure
109 G1 Z+0.5 E-5 X-20 Y-20 F3000 ; move Z up a bit and retract filament even more
110 G90 ; absolute positioning
111 G1 X0 Y250 ; move to cooling position
113 G90 ; absolute positioning
116 start2.gcode = ;Sliced at: {day} {date} {time}
117 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
118 ;Print time: {print_time}
119 ;Filament used: {filament_amount}m {filament_weight}g
120 ;Filament cost: {filament_cost}
121 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
122 ;M104 S{print_temperature} ;Uncomment to add your own temperature line
123 ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
124 ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
126 G90 ;absolute positioning
127 M107 ;start with the fan off
128 G28 X0 Y0 ;move X/Y to min endstops
129 G28 Z0 ;move Z to min endstops
130 G1 Z15.0 F{travel_speed} ;move the platform down 15mm
131 T1 ;Switch to the 2nd extruder
132 G92 E0 ;zero the extruded length
133 G1 F200 E10 ;extrude 10mm of feed stock
134 G92 E0 ;zero the extruded length again
135 G1 F200 E-{retraction_dual_amount}
136 T0 ;Switch to the first extruder
137 G92 E0 ;zero the extruded length
138 G1 F200 E10 ;extrude 10mm of feed stock
139 G92 E0 ;zero the extruded length again
141 ;Put printing message on LCD screen
143 end2.gcode = ;End GCode
144 M104 T0 S0 ;extruder heater off
145 M104 T1 S0 ;extruder heater off
146 M140 S0 ;heated bed heater off (if you have it)
147 G91 ;relative positioning
148 G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
149 G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
150 G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
152 G90 ;absolute positioning
154 start3.gcode = ;Sliced at: {day} {date} {time}
155 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
156 ;Print time: {print_time}
157 ;Filament used: {filament_amount}m {filament_weight}g
158 ;Filament cost: {filament_cost}
159 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
160 ;M104 S{print_temperature} ;Uncomment to add your own temperature line
161 ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
162 ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
164 G90 ;absolute positioning
165 M107 ;start with the fan off
166 G28 X0 Y0 ;move X/Y to min endstops
167 G28 Z0 ;move Z to min endstops
168 G1 Z15.0 F{travel_speed} ;move the platform down 15mm
169 T2 ;Switch to the 2nd extruder
170 G92 E0 ;zero the extruded length
171 G1 F200 E10 ;extrude 10mm of feed stock
172 G92 E0 ;zero the extruded length again
173 G1 F200 E-{retraction_dual_amount}
174 T1 ;Switch to the 2nd extruder
175 G92 E0 ;zero the extruded length
176 G1 F200 E10 ;extrude 10mm of feed stock
177 G92 E0 ;zero the extruded length again
178 G1 F200 E-{retraction_dual_amount}
179 T0 ;Switch to the first extruder
180 G92 E0 ;zero the extruded length
181 G1 F200 E10 ;extrude 10mm of feed stock
182 G92 E0 ;zero the extruded length again
184 ;Put printing message on LCD screen
186 end3.gcode = ;End GCode
187 M104 T0 S0 ;extruder heater off
188 M104 T1 S0 ;extruder heater off
189 M104 T2 S0 ;extruder heater off
190 M140 S0 ;heated bed heater off (if you have it)
191 G91 ;relative positioning
192 G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
193 G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
194 G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
196 G90 ;absolute positioning
198 start4.gcode = ;Sliced at: {day} {date} {time}
199 ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
200 ;Print time: {print_time}
201 ;Filament used: {filament_amount}m {filament_weight}g
202 ;Filament cost: {filament_cost}
203 ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
204 ;M104 S{print_temperature} ;Uncomment to add your own temperature line
205 ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
206 ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
207 ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
209 G90 ;absolute positioning
210 M107 ;start with the fan off
211 G28 X0 Y0 ;move X/Y to min endstops
212 G28 Z0 ;move Z to min endstops
213 G1 Z15.0 F{travel_speed} ;move the platform down 15mm
214 T3 ;Switch to the 4th extruder
215 G92 E0 ;zero the extruded length
216 G1 F200 E10 ;extrude 10mm of feed stock
217 G92 E0 ;zero the extruded length again
218 G1 F200 E-{retraction_dual_amount}
219 T2 ;Switch to the 3th extruder
220 G92 E0 ;zero the extruded length
221 G1 F200 E10 ;extrude 10mm of feed stock
222 G92 E0 ;zero the extruded length again
223 G1 F200 E-{retraction_dual_amount}
224 T1 ;Switch to the 2nd extruder
225 G92 E0 ;zero the extruded length
226 G1 F200 E10 ;extrude 10mm of feed stock
227 G92 E0 ;zero the extruded length again
228 G1 F200 E-{retraction_dual_amount}
229 T0 ;Switch to the first extruder
230 G92 E0 ;zero the extruded length
231 G1 F200 E10 ;extrude 10mm of feed stock
232 G92 E0 ;zero the extruded length again
234 ;Put printing message on LCD screen
236 end4.gcode = ;End GCode
237 M104 T0 S0 ;extruder heater off
238 M104 T1 S0 ;extruder heater off
239 M104 T2 S0 ;extruder heater off
240 M104 T3 S0 ;extruder heater off
241 M140 S0 ;heated bed heater off (if you have it)
242 G91 ;relative positioning
243 G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
244 G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
245 G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
247 G90 ;absolute positioning
249 support_start.gcode =
254 preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
255 ;This code is added before the T(n)
256 postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
257 ;This code is added after the T(n)